• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.3
• /
• pp.309-316
• /
• 2000

A coordination method for a macro/micro robot with separate controllers is proposed and evaluated. The macro/micro robot system generally has independent controllers for the macro and the micro robot respectively. A controller for the coordination of the macro and the micro robot has been designed based on the stable independent controller of each system. The method and trajectory generation method is also proposed to track the moving desired position rapidly. The control method and trajectory generation method is also proposed to track the moving desired position rapidly. The control strategy has been implemented to the macro/micron robot system to evaluate the performance. The experimental results show that the proposed method for maintaining the micro robot within its workspace has uniform performance over the various range of the bandwidth and the proposed trajectory generator is shown to be efficient.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.5
• /
• pp.487-495
• /
• 2012

In this paper, a Smart Home Service Robot, McBot II, which performs mess-cleanup function etc. in house, is designed much more optimally than other service robots. It is newly developed in much more practical system than McBot I which we had developed two years ago. One characteristic attribute of mobile platforms equipped with a set of dependent wheels is their omni- directionality and the ability to realize complex translational and rotational trajectories for agile navigation in door. An accurate coordination of steering angle and spinning rate of each wheel is necessary for a consistent motion. This paper develops trajectory controller of 3-wheels omni-directional mobile robot using fuzzy azimuth estimator. A specialized anthropomorphic robot manipulator which can be attached to the housemaid robot McBot II, is developed in this paper. This built-in type manipulator consists of both arms with 4 DOF (Degree of Freedom) each and both hands with 3 DOF each. The robotic arm is optimally designed to satisfy both the minimum mechanical size and the maximum workspace. Minimum mass and length are required for the built-in cooperated-arms system. But that makes the workspace so small. This paper proposes optimal design method to overcome the problem by using neck joint to move the arms horizontally forward/backward and waist joint to move them vertically up/down. The robotic hand, which has two fingers and a thumb, is also optimally designed in task-based concept. Finally, the good performance of the developed McBot II is confirmed through live tests of the mess-cleanup task.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.22 no.5
• /
• pp.617-623
• /
• 2012

In this paper, we propose a gait generation method for a quadruped robot to walk efficiently on the slope, which uses the waist joint of a quadruped robot. We derive the kinematic model of a quadruped robot with waist joint using the Denavit-Hartenberg representation method and the algebraic method. In addition, the gaits are generated based on the wave gait. In the proposed gait generation method, first in order to alleviate the mechanical restriction and the reduction of the stride, we determine the appropriate waist joint angle according to the slope degree, and then decide the location of the tiptoe of a quadruped robot by exploring the workspace. Finally, through computer simulations, we verify the effectiveness and applicability of the proposed method.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1832-1835
• /
• 1997

Off-line programming systems are widely spread in assembly lines of minute electronic products to huge offshore structures. Any OLP system has to be calibrated before the on-line robot tasks are performed because there are inherent differences between the CAD model on OLP and the real robot workspace. This paper uses simple geometric expressions to propose a calibration method applicable to an OLP for SCARA robots. A positioning task on the two-dimensional horizontal surface was used in the error analysis of a SCARA robot and the anaysis shows that the inaccuracy results from the two error sources non-zero offset angles of two rotational joints at the zero return and differences in link lengths. Pen marks on a sheet of plotting paper are used to determine the accurate data on the joint centers and link dimensions. The calculated offset angles and link lengths are fed back to the OLP for the calibration of the CAD model of the robot and task environments.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10a
• /
• pp.915-920
• /
• 1987

When a task requires two robot arms to move in a cooperative manner sharing a common workspace, potential collision exists between the two robot arm . In this paper, a novel approach for collision-free trajectory planning along paths of two SCARA-type robot arms is presented. Specifically, in order to describe potential collision between the links of two moving robot arms along the designated paths, an explicit form of "Virtual Obstacle" is adopted, according to which links of one robot arm are made to grow while the other robot arm is forced to shrink as a point on the path. Then, a notion of "Coordination Chart" is introduced to visualize the collision-free relationship of two trajectories.of two trajectories.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.686-691
• /
• 2001

In this paper, the pneumatic service robot with a hybrid type is developed. A pneumatic has the advantage of good compliance, high payload-to-weight and payload-to-volume ratios, high speed and force capabilities. Using pneumatic actuators which have low stiffness, the service robot can guarantee safety. By suggesting a new serial-parallel hybrid type for the service robot which separates into positioning motion and orienting motion, we can achieve large workspace and high strength-to-moving-weight ratio at the same time. A sliding mode controller can be designed for tracking the desired output using the Lyapunov stability theory and structural properties of pneumatic servo systems. Through many experiments of circular trajectory, the pneumatic service robot is evaluated and verified.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.10
• /
• pp.930-939
• /
• 2004

In this paper, both dynamic constraints and kinematic constraints are considered for the analysis of manipulability of robotic systems comprised of multiple cooperating arms. Given bounds on the torques of each Joint actuator for every robot, the purpose of this study is to drive the bounds of task-space acceleration of object carried by the system. Bounds on each joint torque, described as a polytope, is transformed to the task-space acceleration through matrices related with robot dynamics, robot kinematics, object dynamics, grasp conditions, and contact conditions. A series of mathematical manipulations including the procedure calculating minimum infinite-norm solution of linear equation is applied to get the reachable acceleration bounds from given actuator dynamic constrains. Several examples including two robot systems as well as three robot system are shown with the assumptions of complete-constraint contact model(or' very soft contact') and insufficient or proper degree of freedom robot.

• Journal of Power System Engineering
• /
• v.19 no.3
• /
• pp.75-80
• /
• 2015

Typically, robot system configured by articulated robot manipulator with 1 DOF transfer unit is being applied in automotive manufacturing automation process. Especially, 1 DOF transfer unit is necessary to extend workspace of robot manipulator. In this configuration, because transfer unit works only one direction, robot manipulator only works in one side in case of car body painting or sealing automation process. it is necessary three robot manipulator system at least. In this paper, in order to robot manipulator works effectively in car body sealing automation application, we are suggested omni-directional manipulator system and conducted studying on redundancy resolution method to solve manipulability-optimal problem.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2003.09b
• /
• pp.110-113
• /
• 2003

In this paper, we propose that the chaotic behavior analysis in the mobile robot of embedding Arnold equation with obstacle. In order to analysis of chaotic behavior in the mobile robot, we apply not only qualitative analysis such as time-series, embedding phase plane, but also quantitative analysis such as Lyapunov exponent in the mobile robot with obstacle. In the obstacle, we only assume that all obstacles in the chaos trajectory surface in which robot workspace has an unstable limit cycle with Van der Pol equation.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2003.09b
• /
• pp.5-8
• /
• 2003

In this paper, we propose that the chaotic behavior analysis in the mobile robot of embedding Chua's equation with obstacle. In order to analysis of chaotic behavior in the mobile robot, we apply not only qualitative analysis such as time-series, embedding phase plane, but also quantitative analysis such as Lyapunov exponent in the mobile robot with obstacle. In the obstacle, we only assume that all obstacles in the chaos trajectory surface in which robot workspace has an unstable limit cycle with Van der Pol equation