• International Journal of Highway Engineering
• /
• v.9 no.3
• /
• pp.83-89
• /
• 2007

When allocating traffic signal at the signalized intersection, minimum green time and clearance time for bicyclists should be significantly considered in order to enhance safety aspects to bicyclists when crossing intersections, especially where intersections with exclusive bicycle paths that are physically separated from pedestrians. In this study, field measurements related to bicycle crossing time, including minimum peen time and clearance time, were collected and analyzed according to bicycles crossing types at the signalized intersections where high rate of bicyclists exists. Three types of bicycle crossing are defined as follows 1) stopping: completely stop before crossing (at least one foot on found) 2) riding: crossing with riding bicycle 3) pulling: crossing without riding bicycles. Minimum green time based on pedestrian speeds should be used as crossing time in this case. For bicyclists, speed of bicycle that is applicable to estimate the minimum green time is in the 1.36m/sec($15^{th}$ percentile) to 1.60m/sec($25^{th}$ percentile) range in case of its stopping. Also it is in the 0.75($15^{th}$ percentile) to 0.87($25^{th}$ percentile) range for pulling at crosswalk. In addition, speed of bicycle to consider for calculating the clearance time is in the 2.51m/sec($15^{th}$ percentile) to 2.79m/sec($25^{th}$ percentile). These values also resulted from $15^{th}$ percentile or $25^{th}$ percentile speeds of riding. The results of this study are expected to be supported in traffic signal allocation process, reflecting bicyclists' characteristics.

• International Journal of Highway Engineering
• /
• v.9 no.3
• /
• pp.111-121
• /
• 2007

During the whole month of December in 2005, Korea experienced both heavy snowfall and freezing temperature in southeast regions, which had caused frost related damages to many pavements laid on top of box culverts. In-situ observation revealed that the formation of ice lenses in subgrade and subsequent unbound layers led to upward heaving and transverse cracks in concrete and asphalt pavements. This has affected the long-term performance of pavements, as well as has threatened drivers' safety for a while. Recently, Korea Expressway Corporation has proposed a design guide to better protect newly constructed unbound pavement layers over culverts from frost heave. A trench drainage system has been selected to effectively draw off water and to alleviate pore-water pressure in soils during the coldest season. This paper presents experimental and analytical backgrounds behind this new design guide. Soil specimens retrieved from the sites are tested to quantify clay content and to estimate the permeability of subgrade. A 2-D ground seepage analysis has been conducted to better understand the changes in pore water pressures as a function of grain size. Finally, an optimum size of trench drainage is determined based on numerical analysis and workability in the field.

• International Journal of Highway Engineering
• /
• v.9 no.4
• /
• pp.93-104
• /
• 2007

This study evaluates the mechanical properties of steel fiber reinforced porous concrete for pavement according to content of slag aggregate and fly ash to elicit the presentation of data and the way to enhance its function for the practical field application of porous concrete as a material of pavement. As a result, void ratio and permeability coefficient of porous concrete for pavement increased a little as mixing rate of slag aggregates increased. Void ratio and permeability coefficient increased a lot as mixing rate of fly ash decreased. As fly ash was mixed, national regulation of permeable concrete for pavement(8% and 0.1 cm/sec) was met. Compressive strength and flexural strength decreased as mixing rate of slag aggregates increased, but they increased a lot as mixing rate of fly ash increased. Even when slag aggregates were mixed 50% with 5% fly ash mixed, national regulation of pavement concrete(18MPa and 4.5MPa) was met. In addition, compared to non-mixture, flexural strength increased about 22.8% when 0.75vol.% of steel fiber was added. Regarding sliding resistance, BPN increased as mixing rate of slag aggregates increased. But BPN decreased as fly ash was mixed. Compared to crushed stone aggregates, abrasion resistance and fleers-thaw resistance decreased as mixing rate of slag aggregates increased. When fly ash was mixed, abrasion resistance and freeze-thaw resistance improved remarkably. Compared to non-mixture, 10% mixture of fly ash improved abrasion resistance and freeze-thaw resistance about 5.6% and 14.3 respectively.

• Journal of Korean Society of Transportation
• /
• v.35 no.3
• /
• pp.220-233
• /
• 2017

Traffic volumes are fundamental data widely used in various traffic analysis, such as origin-and-destination establishment, total traveled kilometer distance calculation, congestion evaluation, and so on. The low number of links collecting the traffic-volume data in a large urban highway network has weakened the quality of the analyses in practice. This study proposes a method to estimate the traffic volume data on a highway link where no collection device is available by introducing a spatial statistic technique with (1) the traffic-volume data from TOPIS, and National Transport Information Center in the Ministry of Land, Infrastructure, and (2) the navigation data from private navigation. Two different component models were prepared for the interrupted and the uninterrupted flows respectively, due to their different traffic-flow characteristics: the piecewise constant function and the regression kriging. The comparison of the traffic volumes estimated by the proposed method against the ones counted in the field showed that the level of error includes 6.26% in MAPE and 5,410 in RMSE, and thus the prediction error is 20.3% in MAPE.

• Journal of Korean Society of Rural Planning
• /
• v.24 no.4
• /
• pp.147-155
• /
• 2018

The purpose of this study was to identify vulnerable area of emergency medical care. In the existing method, the emergency medical vulnerable area is set as an area that can not reach the emergency room within 30 minutes. In this study, we set up an area that can not reach within 30 minutes including the accessibility of 119 emergency center. To accomplish this, we obtained information on emergency room and 119 emergency center through Open API and constructed road network using digital map to perform accessibility analysis. As a result, 509 emergency room are located nationwide, 78.0% of them are concentrated in the region, 1,820 emergency center are located, and 61.0% of them are located in rural areas. The average access time from the center of the village to the emergency room was analyzed as 15.3 minutes, and the average access time considering the 119 emergency center was 21.8 minutes, 6.5 minutes more. As a result of considering the accessibility of 119 emergency center, vulnerable areas increased by 2.5 times, vulnerable population increased by 2.0 times, and calculating emergency medical care vulnerable areas, which account for more than 30% of the urban unit population, it was analyzed that it increased from 17 to 34 cities As a further study, it will be necessary to continuously monitor and research the real-time traffic information, medical personnel, medical field, and ambulance information to reflect the reality and to diagnose emergency medical care in the future.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.5
• /
• pp.621-640
• /
• 2019

Quantitative stability assessment of underground cavities can be presented as a factor of safety based on the Shear Strength Reduction Method (SSRM). Also, SSRM is one of the stability evaluation methods commonly used in slope stability analysis. However, there is a lack of research that considers the relationship between the probability of occurrence of cavities in the ground and the potential failure surface of the slope at the same time. In this study, the effect of small underground cavities on the failure behavior of the slope was analyzed by using SSRM. Considering some of the glaciology studies, there is a case that suggests that there is a cavity effect inside the glacier in the condition that the glacier slides. In this study, the stability evaluation of underground cavities and slope stability analysis, where SSRM is used in geotechnical engineering field, was carried out considering simultaneous conditions. The slope stability analysis according to the shape and position change of underground cavities which are likely to occur in the lower part of a mountain road was analyzed by using SSRM in FLAC3D software and the influence of underground cavities on the slope factor of safety was confirmed. If there are underground cavities near slope potential failure surface, it will affect the calculation of a factor of safety. The results of this study are expected to be basic data on slope stability analysis with small underground cavities.

• Korean Journal of Heritage: History & Science
• /
• v.48 no.3
• /
• pp.204-219
• /
• 2015

International society, including the United Nations, has recently been making efforts to further promote a rapprochement of cultures in relation to alleviating military and political conflicts and other social clashes. In line with these efforts at the international level, there has been a growing interest on Central Asia and, in particular, on the Silk Road, which functioned as a trade route among ancient civilizations in the region and is also seen as a route that promoted cultural dialogue and exchanges. Given the amount of cross cultural dialogue and exchange, it is no surprise that intangible cultural heritage has historically been abundant and easily found in the region. However, this heritage was placed in considerable risk because heritage transmission critically weakened for seventy years under Soviet rule. Fortunately, since independence, there has been increasing interest in restoring community identity and reviving intangible heritage. Nevertheless, in spite of this interest, a lack of policies and cultural support in each country has made heritage safeguarding difficult. In this paper, I analyze the various phenomena that took place after the concept and international trends on ICH were introduced and speak about the experiences and outcomes obtained from collaborative network projects by ICHCAP and the Central Asian countries over the last six year. In addition, I would like take this opportunity to discuss how we can understand and develop collaboration in the intangible heritage field in Central Asia in a long-term perspective.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.5
• /
• pp.27-35
• /
• 2019

The purpose of this study is to analyze the displacement characteristics in slow-moving landslide area using digital elevation model and airborne LiDAR when unpredictable disaster such as slow-moving landslide occurred. We also aimed to provide basic data for establishing a rapid, reasonable and effective restoration plan. In this study, slow-moving landslide occurrence cracks were selected through the airborne LiDAR data, and the topographic changes and the scale of occurrence were quantitatively analyzed. As a result of the analysis, the study area showed horseshoe shape similar to the general form of slow-moving landslide occurrence in Korea, and the direction of movement was in the north direction. The total area of slow-moving landslide damage was estimated to about 2.5ha, length of landsldie scrap 327.3m, average width 19.3m, and average depth 8.6m. The slow-moving landslides did not occur on a large scale but occurred on the adjacent slope where roads were located, caused damage to retaining walls and roads. The field survey of slow-moving landslides was limited by accessibility and safety issues, but there was an advantage that accurate analysis was possible through the airborne LiDAR. However, because airborne LiDAR has costly disadvantages, it has proposed a technique to mount LiDAR on UAV for rapidity, long-term monitoring. In a slow-moving landslide damage area, information such as direction of movement of cracks and change of scale should be acquired continuously to be used in restoration planning and prevention of damage.

• Journal of the Korean GEO-environmental Society
• /
• v.20 no.3
• /
• pp.21-30
• /
• 2019

Composite pile, which is composed of the steel pipe pile in which the large horizontal force acts and the PHC pile in which the small horizontal force acts by a special connecting devices, is being commercialized as a base material for civil engineering structures. The core of such a composite pile can be said to be a design criterion for estimating the joint position and stability of the connection device between steel pipe pile and PHC pile. In Korea, there is no precise specification for the location of composite pile joints. In the LH Design Department (Korea Land & Housing Corporation, 2009), "Application of composite pile design and review of design book marking" was made with reference to Road Design Practice Volume 3 (Korea Expressway Corporation, 2001). this is used as a basis of the design of the composite pile. It can not be regarded as a section change of the composite pile, so it has a limitation in application. Therefore, In this study, we propose a design criterion for the location of the section of the composite pile (joint of steel pipe pile and PHC pile) and evaluate the stability and economical efficiency of it by using experimental method and analytical method. Analysis of composite pile design data installed in 79 domestic bridges abutment showed that the stresses, bending moments, and displacements acting on the pile body and connection of the pile were analyzed. Through the redesign process, it was confirmed that the stresses generated in the connecting device occur within the allowable stress values of the connecting device and the PHC pile. In conclusion, the design proposal of composite pile joint location through empirical case study in this study is an improved design method considering both stability and economical efficiency in designing composite pile.

• Journal of Practical Engineering Education
• /
• v.10 no.1
• /
• pp.73-79
• /
• 2018

The purpose of this study is to explore the supporting scenario to promote vocational training in North Korea in terms of cooperation level. To this end, we have embarked on a regional and industry based vocational training program by predicting the political and social situation of North Korea and staging three scenarios systematically. These scenarios were designed originally based on the Futures Group methodology. The first scenario is to establish a technical training center in one area, focusing on the electrical, electronics, and clothing sectors. The second scenario is to set up a pilot campus of vocational training college in one region by selecting the electric, electronic, and automobile industries as its main industries. The third scenario is to establish five vocational training college campuses in North Korea, focusing on electricity and electronics, IT manufacturing, telecommunications, heavy industry, and women-specialized industries. We suggested the followings: First, establishing goals and strategies for North Korean vocational training and establishing road maps. Second, the North Korean vocational training governance system needs to be established. Third, R & D infrastructure for vocational training needs to be established. Fourth, HRD and HRM system in North Korea vocational training field needs to be established. In addition, the role of public and private employment services centers to provide them should be strengthening.