• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2002년도 전력전자학술대회 논문집
• /
• pp.378-381
• /
• 2002

This paper describes a novel multilevel ad/dc power converter suitable for the protection of frequent output short-circuit. The output dc power of the proposed converter can be disconnected from the load within several hundred microseconds at the instant of short-circuit fault. The rising time of the dc load voltage is as small as several hundred microseconds, and there is no overshoot of the do voltage because the dc output capacitors keep undischarged state. Analysis and simulations are carried out to investigate the operation and usefulness of the proposed scheme.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 전력전자학술대회 논문집
• /
• pp.413-417
• /
• 1998

In order to obtain better performance for a SRM(switched reluctance motor) drive, the commutation from one phase to another must be as fast as possible. In this paper a novel converter for SRM drive is proposed, which can accelerate the turn-off and turn-on time by using two capacitors to form a resonant circuit with the motor inductance. Two capacitors recover rapidly stored energy in the off going phase and establish rapidly the current rising in the on going phase. As a result, the current tail can be shortened and the dwell angle in the positive torque region can be extended. And comparing with the asymmetric converter, this converter has higher energy availability in energy conversion process and less number of switches.

• Journal of Power Electronics
• /
• 제11권4호
• /
• pp.612-619
• /
• 2011

This paper presents a water treatment system for leachate from sewage-filled ground that uses a pulsed-power modulator developed based on semiconductor switches in order to realize a long life, a high repetition rate, and a fast rising time. The specifications of the developed pulsed-power modulator are the pulsed output voltage, the output current, the pulse repetition rate (PRR), the pulse width, and an average output power of $60\;kV_{max}$, $300\;A_{max}$, 3000, $50\;{\mu}s$, and 15 kW, respectively. The pulsed-power water treatment system was introduced and analyzed using an equivalent electrical circuit model to optimize the output voltage waveform. The experimental results verify that the proposed water treatment system can be effectively used for industrial applications.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권7호
• /
• pp.329-333
• /
• 2001

The pulsed poser system has been widely used to many applications, such as E/P(Electrostatic Precipitator), DeNox/DeSOx power system, ozon generator, etc. A pulse energy efficiency for load depends on the rising time, peak value, pulse duration and impedance matching, etc. The pulse generator generally required for short pusle duration and high peak value was forced to consider its volume and economy. In this study, developing a compact pulse generator that applied for cascading method to be made of two pulse transformers, we compared cascading voltage with non cascading one by applying the pulse energy to load. Adopting cascading technique to pulse transformer, we found that average cascading voltage was about 60[%] of theoretical value. Maximum cascading ratio was calculated at 60 times compared with non cascading voltage.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 A
• /
• pp.384-388
• /
• 1999

This paper presents auto-tuning to compensate the integrator windup of the current and the speed PID controller of DC motor, which suppress the overshoot of transient response without delay of rising time. The simulation results using Matlab show the validity of auto-tuning methods.

• 한국자동차공학회논문집
• /
• 제1권3호
• /
• pp.63-73
• /
• 1993

In this paper, fuzzy control algorithm for the speed ratio control of the electro-hydraulic rig type continuously variable transmission(CVT) was proposed and the CVT performance tests were carried out for the optimal operation of the engine simulator. The experimental results for the constant throttle and the acceleration modes showed that the engine can be run on the optimum operating line, representing the power and economy mode, by the fuzzy control of the CVT speed ratio. Comparing the PID control with the fuzzy control, it was found that the fuzzy control showed better performance with the faster rising time and smaller steady state error. The result of this study can be used as basic design materials for developing the transmission control unit of the CVT.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.360-360
• /
• 2000

In this paper, a new criterion f9r determining the sampling rate of digital conroller is proposed. This paper will introduce a method fur determining the appropriate sampling rate of digital controller which can be substituted with the given analog controller, using phase margin and gain cross over frequency, not rising time or bandwidth of the closed-loop system. This method also guarantees performance of the system. Without exact modeling functions of the plant, abstracting those functions, this paper can achieve stability and aimed performance of the system, and this paper proved it with proper modeling functions.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.369-369
• /
• 2000

Control system by means of fuzzy theory has demonstrated its robustness in applying to the high-order and nonlinear dynamic system in that it can utilizes the human expert knowledges in system design. In this paper, first, the design methodology of HFC combined PID controller with fuzzy controller by membership function of weighting coefficient is proposed. Second, Second, an auto-tuning algorithms utilizing the simplified reasoning method and genetic algorithms is presented to improve the performance of hybrid fuzzy controller. Especially, in order to obtain the optimal scaling factors and PID parameters of HFC using GA based on advanced initial individual, three kinds of estimation modes such as basic, contraction, and expansion mode are effectively utilized. The proposed HFC is evaluated and discussed in ITAE, overshoot and rising time to show applicability and superiority with simulation results.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 금형가공 심포지엄
• /
• pp.95-102
• /
• 2002

With recent trends leaning towards product miniaturization, the advent of new material and speedy delivery times, old style conventional trial-and-error methods have been only serving to weaken corporate competitiveness. Reliant on tiny increments of time-consuming experience, this antiquated approach begets a delayed delivery of product development, cost loss and quality depreciation. To solve such problems, the Dedicated Injection Molding CAPA (Computer Aided Plastics Application) performs a preliminary examination on problems rising from every stage of creation - from appropriate material selection and mold design to mass production - through a computer system. Thus, it determines the optimum design variables and process conditions while diagnosing and solving defective molds.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 추계학술대회 논문집
• /
• pp.413-416
• /
• 1996

The ceramic dielectrics were fabricated by mixing of Mn $O_2$ and ZnO at (B $a_{0.85}$ $Ca_{0.15}$)Ti $O_3$ and studied for dielectric relaxation characteristics. The dielectric relaxation time was increased by space charge polarization of palaelectric layer at the low temperature and frequency but it was decreased by Interface polarization at the high temperature and frequency. The remnant polarization and coercive field of ceramic dielectrics was decreased by rising temperature.ure.