• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.59-60
• /
• 2015

본 논문에서는 3-Level NPC(Neutral Point Clamped) 인버터에서 ZDPWM(Zero Dead Time Pulse Width Modulation) 기법에 대해서 제안한다. 3-Level NPC 인버터에서 기존 PWM 기법은 각 스위치는 서로 상보적인 동작을 수행하고, 반도체 스위칭 소자 특성상 Rise Time과 Fall Time의 시간차이로 인하여 단락사고를 방지하기 위해 스위칭 신호의 Rising Edge에 데드타임을 인가하여 단락을 방지한다. 그러나 이러한 데드타임은 지령 스위칭 신호와 실제 스위칭 신호의 오차로 인하여 출력 전압 및 전류에 왜곡이 발생하고, 이러한 왜곡으로 인하여 시스템의 오작동 및 직류링크단 전압의 불평형의 원인이 된다. 제안하는 PWM기법은 지령전압과 출력전류의 위상에 따라 영역을 나눈 후 전류의 방향에 따라 옵셋 전압을 생성하여 새로운 지령전압을 만들어 각 스위치에 스위칭 신호를 인가한다. 제안한 기법에 타당성을 증명하기 위해 시뮬레이션을 통해 검증하였다.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.30 no.4
• /
• pp.707-714
• /
• 2003

Plasma Arc Curing(PAC) units operate at relatively high intensity and claimed to result in optimum properties of composite resin in a short curing time, so the interest of pediatric dentists about PAC units have been increased recently. But PAC units used for polymerizing restorative resins produce heat during operation. The purpose of this study was to evaluate temperature transmission through dentin of various depths using two types of PAC units(Flipo, Q-Lux plasma 100). The results from the present study can be summarized as follows : 1. When PAC be used continuously, temperature on tip was increased as curing times, and Q-Lux showed greater temperature rising(p<0.001). 2. Compared temperature transmission as dentin depth, temperature rising rate was decreased as dentin thickened(0.5, 1.0, 1.5, 2.0mm)(p<0.05). 3. Compared temperature transmission as resin depth, temperature rising rate was also decreased as resin thickened(1.0, 2.0mm)(p<0.05).

• Journal of the Korean Society of Costume
• /
• v.67 no.2
• /
• pp.131-146
• /
• 2017

The aim of this study is to investigate the operating characteristics of fashion start-up companies and the characteristics of their founders. For this purpose, this study surveyed fashion start-up companies via online survey in May 2015, and analyzed the data from one hundred companies. The results are as follows. First, for the characteristics of the founders, female founders constituted 65.0% and male founders 35.0%. At the time of establishment, founders aged 26-35 constituted 77.0%. Founders with less than five years of work experience made up about 80%. 82.1% of the founders participated in domestic and foreign exhibitions/fairs. 41.0% of the founders were awarded fashion contest and competition awards, and 33.3% of the founders were supported by rising designer support projects. Second, for the operating characteristics of the start-up companies, clothing at 78.0% was the most popular entrepreneurial item, and the majority targeted the age 20-30 group. 78.0% of the companies had less than 40 production styles per season, and all the enterprises had less than 5 employees. 59.0% of the companies had export experience. Exports to China, Hong Kong, and Japan accounted for 67.4% of all exports. Major distribution channels were mainly select shops(offline select shops 79.8%, online select shops 62.8%). The main methods of promotion were fashion media articles/interviews, product sponsorship, and SNS. The most preferred distribution channel was becoming a part of online/offline select shops(92.6%). Viral marketing(84.4%), star marketing and costume sponsorship(66.7%) were the most preferred method of promotion. The most preferred way to enter foreign markets was to participate in domestic and foreign exhibitions/fairs/trade shows. This study provides basic data necessary for future founders preparing to launch fashion start-up companies. It also aids fashion start-up companies in developing more advanced business operation strategies.

• Journal of the Korean GEO-environmental Society
• /
• v.2 no.1
• /
• pp.57-65
• /
• 2001

In this study, the seepage behavior and the stability of the extension embankment were estimated for three cases the permeability coefficient of an extension part and the rising velocity due to the rainfall of flood period. In parallel flow condition, the unstability of the slope due to embankment erosion was examined by analyzing the variation of seepage line by the seepage modeling tests and FEM analysis, and the stability of the embankment slope accompanied by the sudden rise of the water level after the flood. The seepage behavior of extension embankment indicates that the larger permeability of the extension part the longer initial seepage distance, and the exit point from embankment slope is gradually increased, and then shows unstable seepage behavior that occurs a partial collapse as safety factor decreases with time. It is because of the increment of exit points due to variation of seepage line and rising velocities of water level. Also, the collapse aspect of embankment slope shows that the increment rising velocities of water level causes the increment collapse height and depth.

• Journal of Korean Foot and Ankle Society
• /
• v.27 no.1
• /
• pp.12-16
• /
• 2023

Purpose: Postoperative exercise for acute Achilles tendon rupture is important for a patient's return to daily life and sports. On the other hand, the protocol requires considerable effort to educate patients and continuous checking. This study evaluated the outcome of a new simple and delayed rehabilitation protocol after Achilles tendon rupture repair. Materials and Methods: From July 2014 to November 2020, one hundred eighty-three patients were operated on by one surgeon. The exercise protocol was classified into two methods. One group (immediate protocol, control group) started immediate full weight bearing with a 20° plantar flexion range of motion from two days postoperatively. Ankle dorsiflexion was restricted to 0°. The other group (delayed protocol, case group) started full weight bearing with a controlled ankle motion boot from two weeks postoperatively. No range of motion exercise was allowed until six weeks postoperatively. Age, sex, body mass index, ankle range of motion, muscle power, time to return to previous physical activity, functional score, and complication rate were evaluated. The results of the two groups were compared using a Mann-Whitney test. Statistical significance was set as p<0.05. Results: The range of motion, double heel rising, and one-leg standing were achieved faster in the control group (p<0.05). However, single-heel rising, repeated single-heel rising, return to previous activity (work, run, and sport), and functional scores showed no statistical difference (p>0.05). Conclusion: Simple and delayed postoperative rehabilitation of acute Achilles tendon rupture without active range of motion exercises showed satisfactory functional results and a low complication rate.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.6
• /
• pp.109-118
• /
• 2008

Carbon fiber reinforced polymer(CFRP) can be bonded to the soffit of a concrete beam as a means of repairing and strengthening the beam. In such beams, materials, concrete and carbon fiber sheets, are different in coefficient of thermal expansion. Consequently, interfacial shear stresses can be increased and debonding failure may occur at the plate ends due to temperature rising. This paper presents a method of approximate closed-form solutions for the interfacial shear stresses and conducts a beam test to compare the numerical results. In case of temperature rising over $30^{\circ}C$, interfacial stress of 0.91MPa is occurred at the end of sheet. Therefore, using carbon fiber sheet for strengthening the concrete beam, it is necessary to consider the thermal effects and to evaluate the long time behavior of the concrete beam by temperature change.

• Journal of Korean Society for Atmospheric Environment
• /
• v.23 no.4
• /
• pp.449-456
• /
• 2007

Dispersion coefficient preprocessing schemes have been examined to improve plume dispersion model performance in complex coastal areas. The performances of various schemes for constructing the sigma correction order were evaluated through estimations of statistical measures, such as bias, gross error, R, FB, NMSE, within FAC2, MG, VG, IOA, UAPC and MRE. This was undertaken for the results of dispersion modeling, which applied each scheme. Environmental factors such as sampling time, surface roughness, plume rising, plume height and terrain rolling were considered in this study. Gaussian plume dispersion model was used to calculate 1 hr $SO_2$ concentration 4 km downwind from a power plant in Boryeung coastal area. Here, measured data for January to December of 2002 were obtained so that modelling results could be compared. To compare the performances between various schemes, integrated scores of statistical measures were obtained by giving weights for each measure and then summing each score. This was done because each statistical measure has its own function and criteria; as a result, no measure can be taken as a sole index indicative of the performance level for each modeling scheme. The best preprocessing scheme was discerned using the step-wise method. The most significant factor influencing the magnitude of real dispersion coefficients appeared to be sampling time. A second significant factor appeared to be surface roughness, with the rolling terrain being the least significant for elevated sources in a gently rolling terrain. The best sequence of correcting the sigma from P-G scheme was found to be the combination of (1) sampling time, (2) surface roughness, (3) plume rising, (4) plume height, and (5) terrain rolling.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.187-187
• /
• 2009

The PVA(patterned vertical alignment) mode has a excellent dark state at normal direction. but they has a disclination area at divided domain region at voltage on state. so this disclination make a slow response time and decrease transmittance. To overcome this problem, we research about polymer stabilized vertical alignment (PS-VA) method which was using the UV curable reactive mesogen. According to our research, UV exposure condition which was UV dosage condition effected to rising time and decay time and also threshold voltage.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.6
• /
• pp.873-879
• /
• 2016

A charge pump circuit with very short turn-on time is presented for minimizing reference spurs in CMOS PLL frequency synthesizers. In the source switching charge pump circuit, applying proper voltages to the source nodes of the current source FETs can significantly reduce the unwanted glitch at the output current while not degrading the rising time, thus resulting in low spur at the synthesizer output spectrum. A 1.1-1.6 GHz PLL synthesizer employing the proposed charge pump circuit is fabricated in 65 nm CMOS. The current consumption of the charge pump is $490{\mu}A$ from 1 V supply. Compared to the conventional charge pump, it is shown that the reference spur is improved by dB through minimizing the turn-on time. Theoretical analysis is described to show that the measured results agree well with the theory.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.277-280
• /
• 2008

Recently, a demand of nano/micro patterned polymer for display or biochip has been rising. Then many studies have been carried out. Nano/micro-embossing is a deformation process where the workpiece materials is heated to permit easier material flow and then forced over a planar patterned tool. In this work, the hot-emboss process is performed with different forming conditions; forming temperature, load, press hold time, to get the proper condition for linear pattern fabrication on plated-type polymers (PC). Replicated pattern depth increases in proportion to the forming temperature, load and time. Reduction of the workpiece thickness increases according to press hold time. In process of time, reduction ratio of workpiece thickness decreases because of surface area increment of the workpiece and pressure decline on it.