• 오토저널
• /
• 제4권3호
• /
• pp.48-55
• /
• 1982

In the present the strain gauge type torque transducers consist of solid shaft as sensor, slip ring, brush and bridge circuit as detecting circuit. So in the case of measuring the low-capacity torque, the error caused by technical mistake in mounting stain gauge on the small sensor and especially by contact resistance between slip ring and brush takes place more than the large sensor. Therefore in this study constant voltage in order to have no effect of contact resistance is supplied to the hollow shaft and Schrobron Bridge Circuit. Through the experiment good results were obtained as follows; linearity, hysterisis and zero drift as static characteristics is within 1% F.S respectively. Also when loading, zero drift is about 2% F.S.

• 제어로봇시스템학회논문지
• /
• 제7권8호
• /
• pp.697-702
• /
• 2001

The ring laser gyro(RLG) has been used extensively in strapdown inertial navigation system(SDINS) because of the apparent of having wide dynamic range, digital output and high accuracy. The dithered RLG system has dynamic motion at sensor level, caused by the dithering motion to overcome the lock-in threshold. In this case, an attitude error is produced by not only the true coning of the vehicle motion but also the pseudo coning of the sensor motion. This paper describes the definition of the multi-frequency coning motion and its noncommutativity error to reject the pseudo coning error produced by the sensor motion such as the dithered RLG. The simulation results are presented to minimize the multi-frequency coning error.

• 전기전자학회논문지
• /
• 제11권4호
• /
• pp.293-296
• /
• 2007

루프 공진기 구조를 가지는 비침습식 혈당 센서 구조를 제작하여 혈당 측정을 위한 민감도 측정을 하였다. 0%와 20%의 글루코스 용액의 전기적 특성을 확인하고, 25mm${\sim}$170mm의 지름을 가지는 링 구조를 이용하여 식염수 중 글루코스 농도에 따른 반사 손실의 차이를 측정하였다. 링 형태 프로브가 혈액과 같은 인체 내부의 물질을 측정하는데 종단 개방 프로브에 비해 유리한 특성을 가지며, 측정 주파수 중 가장 낮은 285MHz에서 S11이 0.94의 차이를 보여, 저주파일수록 민감도가 향상됨을 알 수 있었다.

• 대한기계학회논문집A
• /
• 제32권1호
• /
• pp.77-82
• /
• 2008

Strain-gauges have been dominantly used to measure strain at various points on a rotor, however, either a slip ring or telemetry has to be used to send sensor signals to data acquisition instruments at stationary side. Both slip ring and telemetry have numerous inherent problems which force severe limitations in real applications. This paper introduces a new rotor condition monitoring system using FBG(Fiber Bragg Grating) sensors and a rotary optical coupler. A single optical fiber with many FBG sensors is installed on the rotor and an optical dynamic interrogator is installed at stationary side. The sensor signal connection between rotating part and stationary part is made by the rotary optical coupling method which makes use of light's unique characteristic-light travels through space. Broad band light source from the interrogator travels to the optical fiber on the rotor and reflected FBG sensor signals travel back to the optical fiber on stationary side and are connected to the interrogator. Rotary optical coupler's insertion loss change due to rotation is compensated by using a reference sensor installed at the center of the rotor. The proposed system's performance has been successfully demonstrated by accurately measuring strains at 5 points on a blade rotating at high speed.

• ETRI Journal
• /
• 제33권5호
• /
• pp.791-801
• /
• 2011

Security in wireless sensor networks (WSNs) is an upcoming research field which is quite different from traditional network security mechanisms. Many applications are dependent on the secure operation of a WSN, and have serious effects if the network is disrupted. Therefore, it is necessary to protect communication between sensor nodes. Key management plays an essential role in achieving security in WSNs. To achieve security, various key predistribution schemes have been proposed in the literature. A secure key management technique in WSN is a real challenging task. In this paper, a novel approach to the above problem by making use of elliptic curve cryptography (ECC) is presented. In the proposed scheme, a seed key, which is a distinct point in an elliptic curve, is assigned to each sensor node prior to its deployment. The private key ring for each sensor node is generated using the point doubling mathematical operation over the seed key. When two nodes share a common private key, then a link is established between these two nodes. By suitably choosing the value of the prime field and key ring size, the probability of two nodes sharing the same private key could be increased. The performance is evaluated in terms of connectivity and resilience against node capture. The results show that the performance is better for the proposed scheme with ECC compared to the other basic schemes.

• 센서학회지
• /
• 제14권1호
• /
• pp.42-46
• /
• 2005

It has been known that 1/f noise of MOSFET is generated by superposition of random telelgraph signals (RTS). In this study, jitters and phase noise caused by 1/f noise of MOSFET are analysed with RTS supplied to all of the nodes of the CMOS ring oscillator under investigation. Through the analysis of jitters and jitter ratios with varying values of the amplitude of RTS, it is found that the jitters and the jitter ratios are proportional to the amplitude of RTS. And the analysis of FFT of the output of the ring oscillator reveals that the jitters are closely related to the phase noise of the high order harmonics of the ring oscillator outputs.

• 한국소음진동공학회논문집
• /
• 제16권11호
• /
• pp.1172-1178
• /
• 2006

Measurement of blade strain with sensors directly installed on the blade has one critical issue, how to send the sensor signal to the ground. Strain-gauges have been dominantly used to directly measure stress of a blade and either a slip ring or a telemetry system has to be used to send measured signal to the ground. However, both systems have many inherent problems and sometimes very severe limitations to be practically used. In this paper, new on-line strain monitoring method using. FBG(Fiber Bragg Grating) sensors and a beam coupler is introduced. Measurement of rotor stress using FBG sensors is nothing new, but unlike other system which installs all necessary instruments on the rotor and use telemetry system to send data to the ground, this system makes use of light's unique characteristic - light travels through space. In this new approach, single optical fiber with many FBG sensors is installed on the blade and all other necessary instruments can be installed at ground thereby giving tremendous advantages over slip ring or telemetry system. A reference sensor is also introduced to compensate the beam coupler's transmission loss change due to rotation. The suggested system's good performance is demonstrated with experiments.

• 한국전자파학회논문지
• /
• 제27권2호
• /
• pp.123-130
• /
• 2016

본 논문에서는 원격 화학 센서로 활용 가능한 플렉서블 미세유체 메타물질 흡수체를 제안한다. 제안된 흡수체는 잉크젯 프린팅 기법으로 종위 기판 위에 인쇄한 분할고리공진기(SRCR: Split Ring Cross Resonator)와 Polydimethylsiloxane(PDMS) 기판에 레이저 식각된 미세유체 채널로 구성되어 있어 매우 유연한 특징을 보인다. 본 연구에서 제안한 메타물질 흡수체는 미세유체 채널에 주입된 화학물질에 따른 실효 유전율의 변화를 공진주파수의 이동으로 감지할 수 있다. 제안된 흡수체는 시뮬레이션과 측정을 통하여 성능을 검증하였다. 측정 결과, 공기의 경우에는 10.49 GHz에서 흡수가 되었고, 에탄올과 탈이온수의 경우에는 각각 10.04 GHz와 8.9 GHz에서 흡수체로 동작함을 확인할 수 있었다.

• 한국군사과학기술학회지
• /
• 제22권2호
• /
• pp.189-196
• /
• 2019

The inertial sensor errors in SDINS(Strapdown Inertial Navigation System) can be compensated by rotating the inertial measurement unit and it is called RINS(Rotational Inertial Navigation System). It is assumed that the error of the inertial sensor in RINS is a static bias. However, the error of the inertial sensor actually developed and produced is not a static bias due to the change of the temperature applied to the sensor and the influence of the earth's gravity acceleration. In this paper, we propose a six-position gyro bias calibration method to evaluate the gyro bias required for RINS and present the test results of applying it to a ring laser gyro inertial navigation system under development.

• 한국항행학회논문지
• /
• 제23권1호
• /
• pp.69-76
• /
• 2019

본 논문에서는 평면 유전체 기판의 유전율 측정을 위해 마이크로스트립 결함 접지구조를 기반으로 한 고감도 마이크로파 센서의 설계 방법에 대하여 연구하였다. 제안된 센서는 H-모양 개구의 리지 구조를 커패시터 기호 모양으로 변형하여 설계하였다. 제안된 센서의 감도를 기존의 이중 링 상보형 분할 링 공진기를 기반으로 한 센서의 감도와 비교하였다. 두 센서는 피 시험 기판이 없는 상태에서 전송 계수가 1.5 GHz에서 공진하도록 0.76 mm 두께의 RF-35 기판 상에 설계하고 제작하였다. 피 시험 기판으로 비유 전율이 2.17에서 10.2 범위에 있는 타코닉 기판 5종을 선택하였다. 실험 결과, 전송계수 공진주파수의 이동으로 측정된 제안된 센서의 감도는 기존 이중 링 상보형 분할 링 공진기를 기반으로 한 센서와 비교할 때 1.31배에서 1.62배 증가하는 것을 확인하였다.