• International Journal of Naval Architecture and Ocean Engineering
• /
• v.8 no.5
• /
• pp.456-465
• /
• 2016

In order to optimize the performance of a Wells turbine with fixed guide vanes, the designs of an end plate and a ring on the tip of the turbine rotor are proposed as penetrating blade tip treatments. In this study, numerical investigations are made using computational fluid dynamics (CFD)-based ANSYS Fluent software, and validated by corresponding experimental data. The flow fields are analyzed and non-dimensional coefficients $C_A$, $C_T$ and ${\eta}$ are calculated under steady-state conditions. Numerical results show that the stalling phenomenon on a ring-type Wells turbine occurs at a flow coefficient of ${\phi}=0.36$, and its peak efficiency can reach 0.54, which is 16% higher than that of an unmodified turbine and 9% higher than in the case of an endplate-type turbine. In addition, quasi-steady analysis is used to calculate the mean efficiency and output work of a wave cycle under sinusoidal flow conditions. As a result, it has been found that the ring-type turbine is superior to other types of Wells turbines.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1996.03a
• /
• pp.188-193
• /
• 1996

This study was performed the blankholding force and vee-ring effects on Blanking characteristics, such as maximum blanking force, burnish, dish-shape, hardness. etc, in fine-blanking die by the experimental method. Two types of aluminum (Al. 1050-0, Al 5052-H) Such as annealed and unannealed materials were used for the experiment. In order to get a hydrostatic pressure effect, the clearance was set to 0.5% of the thickness of strip, and the counter punch and stripper plate with Vee-ring was set-up. While this experiment was carrying out, the average blanking Velocity was constant (37.5mm/sec) As a result of this study, we got a good surface roughness and a glassy shear plane(burnish) of the sheet over 90% thickness, and such as the excellent accuracy of dimensions, the good squareness and the reduction of dish-shape could be obtained, and also the additional results obtained were such that the hardness of shear plane was increased and the maximum blanking force was reduced in the condition of Vee-ring height of 1.0~1.5mm, and blankholding force of 1200kg.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.4
• /
• pp.99-104
• /
• 2020

In this study, the temperature distribution and heat transfer characteristics of each component in a solenoid motor system were numerically investigated when heat is generated by the steel pad attached to the solenoid ring of the motor. It was found that the internal airflow was complicated by the inflow velocity of air and the rotation of guide rollers and solenoid rings. Based on the numerical results, the tendency for temperature changes in the steel panel was lower due to the contact of the cooling air in the front in the rotational direction, and the peak temperature was at the front of the center. In particular, it was confirmed that as the air inflow rate was increased, the temperature was reduced due to strong convection. The temperature of the iron plate pad was decreased as the convective heat transfer coefficient was linearly increased with increasing airflow around the solenoid ring. In addition, the temperature of the iron plate panel was rapidly increased with increasing heat generation.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.5
• /
• pp.157-163
• /
• 1996

This paper is concered on the development of low-cost fine blanking die with two fluid chambers of which the pressure can be controlled by a hydraulic unit and its application to producting circular blanks in a conventional hydraulic press, not in a special triple-action press usually adopte in fine blanking operation. Four important working parameters affecting on the precision accuracy of products such as existence and position of Vee-ring, stripping force and counter punching force are primarily considered for experiments. Finite element analysis by suing ABAQUA software is approxi- mately made for blanking of circular specimen with a flat stripper plate and then compared with experimental measurements. The the theoretical prediction of camber height which represents deflection of a dish-shaped specimen after blanking seems to give a qualitatively good agreement. It is shown through experiments the the camber height decreases with decreasing stripping force and also with increasing counter punching force, but particularly depending on the latter much more than the former.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.706-710
• /
• 2008

The experiment of dome port cover under shock impact is performed with shock tube. The dome port cover blocked intake air duct up from the solid propellant during air breathing vehicle speed reach Mach 2.0. When the air breathing vehicle reach Mach 2.0, the inlet cover is removed and the dome port cover is broken to pieces by detonator or pressure of inlet air. Thus the dome port cover not only must stand the pressure of combustion chamber but also easy to break from the RAM pressure. In this study, a fracture evaluation on the $Al_2O_3$ ceramic spherical dome and circular plate port under impact has been presented. Ceramic were supported by the rigid body and a couple of O-ring. The Mooney-Rivlin model have been used to describe behaviors of both O-ring. And spherical dome and circular plate fracture results of the LS-DYNA code using Johnson-Holmquist(JH-2) constitutive equation was compared.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.7
• /
• pp.840-843
• /
• 2012

In this paper, the authors present a new design for a dual-band metamaterial(MTM) absorber that utilizes resonant-magnetic inclusion of a split-ring resonator(SRR). The proposed MTM unit cell is constructed by two open complementary split-ring resonators(OCSRRs) and an SRR arrangement. To avoid the need for metallic back plate a planar array of SRRs for resonant-magnetic inclusion is placed facing toward the incident wave propagation direction. Each unit cell is printed on the two sides of a FR-4 substrate. A prototype absorber was fabricated with a planar array of $39{\times}39$ unit cells, and measured. The proposed backplane-less absorber can be used for microwave applications.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.191-192
• /
• 2005

The reverse breakdown voltages of 4H-SiC SBD(schottky barrier diode)s with FP(Field Plate) and/or FLR(Field Limiting Ring) as a edge termination, were investigated. The breakdown voltages of SBDs with FP ware investigated varying the overlap width from $1{\mu}m$ to $30{\mu}m$. The maximum average breakdown voltages was 475V. There is no significant changes for the devices with overlap width of between $5{\mu}m\sim30{\mu}m$. It was confirmed that the dielectric breakdown of the thin thermal oxide is main cause of device failure. However, the breakdown voltage of SBD with FLR was 1400V even though the FLR edge termination structure was not optimized.

• Conservation Science in Museum
• /
• v.7
• /
• pp.11-24
• /
• 2006

Plate armour is an important cultural property that reflects the ancient weaponry and the manufacturing technology of ironware as they are. Among the kinds of iron armour, horizontal plate armour has been very rarely excavated, and there are a few artifacts in their unimpaired shape like the plate armour excavated from Mangisanseong. This report reviews the manufacturing technology of ancient plate armour through its radiograph using appliable nondestructive irradiation and scientific conservation treatment. The seven-tiered plate armour excavated from Mangisanseong has ring hinge to open and shut the right side neck guard. The readout result of radiograph proved iron safety guard of Godaepan (a plate that links neck plate and horizontal plate) and leather safety guard of the right armpit with plate overlap and perforation interval; perforations that seem to have linked shoulder strap on wearing the armour are also observed. In particular, it is identified that the perforation and riveting technique avoided the connection of more than three plates with a rivet. This is an important material to illustrate the best use of function of plate armour overcoming its limit.

• Journal of Plant Biology
• /
• v.36 no.4
• /
• pp.345-355
• /
• 1993

Anatomical study of the secondary xylem in Araliaceous plants, induding 7 genera and 11 species grown in Korea, was carried out to elucidate the relationship among genera in the family. Wood of Hedera has difbse porous and shows ulmiform pattern of angular vessels, simple perforation plate, and alternate pitting. In addition, its ray is homogeneous type II with only procumbent ray cell. Ring porous wood of Dendropanax shows ulmiform of angular vessels, simple perforation plate, alternate pitting, and heterogeneous type II ray, which has sometimes horizontal secretory cavity. Fatsia has diffuse porous wood, which shows ulmiform of angular vessels, scalariform perforation plate (3-9 bars), scalariform pitting, spiral thickening in the lateral wall of vessel, and heterogeneous type II ray with sheath cells. Kalopanax has ring porous wood, which shows ulmiform of circular vessels, simple perforation plate and alternate pitting, and heterogeneous type II ray. While K pictum appears tylose with septum, K pictum var. maximowczii appears tylose without septum. Echinopanax shows ring porous wood, ulmiform of angular vessels, simple perforation plate, scalariform pitting, and tylose with septum. And the ray of Echinopanax is paedomorphic type I composed of only upright cells. Acanthopanax genus is composed of diffuse porous wood, ulmiform of angular vessels, simple perforation plate and alternate pitting. In this genus, A. sessiliflorus has heterogeneous type II ray, apotracheal axial parenchyma and tylose with septum. A. senticosus appears paedomorphic type I with only upright cells, and tylose with septum. A. koreanum and A. sieboldianum have heterogeneous type II ray but have not tylose. Aralia is composed of ring porous wood, ulmiform of circular vessels, simple perforation plate, alternate pitting, heterogeneous type II ray, and tylose contained both septum and reticulate. On the basis of arrangement, shape, length and diameter of vessel element, the angle of end wall to vessel axis, and ray type, the line of specialization in these genera is as follow: from Fatsia, the most primitive, to the most highly specialized Aralia, throughout Hedera, Acanthopanax, Echinopanax, Dendropanax, and Kalopanax by turns. turns.

• Tribology and Lubricants
• /
• v.24 no.6
• /
• pp.343-348
• /
• 2008

In this paper, a CFD (Computational fluid dynamics) code, FLUENT is adopted to investigate accurate flow characteristics for a slipper bearing which is used swash plate type hydraulic axial piston pump. Static pressure and velocity distributions, and velocity vectors are plotted for different film thickness and slipper rotational velocity. In recess region, there exists a doughnut shaped vortex ring. The static pressure distributions are non-uniform and the flow fields are highly asymmetrical under bearing rotation. Therefore the numerical method adopted in this paper can be use in design of hydrostatic components and further studies are required.