• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.12
• /
• pp.4721-4726
• /
• 2010

The performance characteristics of water-chilling heat pump using CO2 for the control of inverter frequency was investigated experimentally. An experimental apparatus is consisted of a compressor, a gas cooler, an expansion valve, an evaporator and a liquid receiver. All heat exchangers used in the test rig are counter flow type heat exchangers with concentric dual tubes, which are made of copper. The gas cooler and the evaporator consist of 6 and 4 straight sections respectively arranged in parallel, each has 2.4m length. The experimental results summarize as the following: for constant inlet temperature of evaporator and gas cooler, as mass flow rate, compression ratio and discharge pressure increases with the inverter frequency. And heating capacity and compressor work increases, but coefficient of performance(COP) decreases with the inverter frequency of compressor. As inlet temperature of secondary fluid in the evaporator increases from $15^{\circ}C$ to $25^{\circ}C$, compression ratio and compressor work decreases, but mass flow rate, heating capacity and COP increases with the inverter frequency of compressor. The above tendency is similar with performance variation with respect to the variation of inverter frequency in the conventional vapor compression refrigeration cycle.

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.11
• /
• pp.636-641
• /
• 2015

Waste energy conversion to SRF (Solid Refuse Fuel) has the effects not alternative fossil fuel usage but also the reduction of greenhouse gas. But the direct burning of the SRF including a plastic waste generates air pollution problem like soot, dioxin, etc. so that an application of pyrolysis and gasification treatment should be needed. The purpose of this study is to supply a basic thermal data of the pyrolysis gasification characteristics in the plastic-rich SRF which are needed for developing the novel pyrolyser or gasifier. To do so, a bench-scale test rig was newly engineered, and then experiments were achieved for the production characteristics of gas, tar, and char. While SRF sample, gasification air ratio, holding time changed as 2 g, 0.691, 32 min respectively, the $H_2$ 1.36%, $CH_4$ 2.18%, CO 1.88%, $Cl_2$ 15.9 ppm, HCl 6.4 ppm were composed. Also light tar benzene $4.03g/m^3$, naphthalene $0.39g/m^3$, anthracene $0.11g/m^3$, pyrene $0.06g/m^3$, gravimetric tar $18g/m^3$, and char 0.29 g was formed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.6
• /
• pp.1969-1977
• /
• 2010

James Cameron's "Avatar" has broken the national record of movie ticket sales, and it caused the boom of 3D and 3D related fields. This research is focused on the appropriate ways to embrace the stereoscopic 3D cinema and the assumable result in Korea. The new stereoscopic 3D is different from the old fashioned analogue 3D, and it has many possibilities that may influence Korean film industry. Since 1990s, the number of Korean film school has increased drastically, and many of those who graduated from the schools would experience fierce job market. 3D converting projects that require a lot of film majored personnels would solve the overly supplied film majored professionals. Through Korea's hundreds of film schools, when they include 3D filmmaking in their curriculum, they can train and educate 3D related staff such as stereographer, convergence puller, and depth continuity artists, and Korea can be an important 3D staff train center in the world. Educating 3D filmmaking can produce a noticeable result in terms of accepting 3D cinema. Stereoscopic 3D cinema has many possibilities in many fields not only in cinema but also almost every fields that related to the imagery. With government's supports, the investments from the 3D related corporations, and 3D education in colleges would be fast and efficient way to embrace and accept stereoscopic 3D cinema in Korea in terms of the size and the profit.

• Journal of the Korean Society for Railway
• /
• v.15 no.1
• /
• pp.9-16
• /
• 2012

The dynamic stability of railway vehicle has been one of the important issues in railway safety. The dynamic simulator has been used in the study about the dynamic stability of railway vehicle and wheel/rail interface optimization. Especially, a small scale simulator has been widely used in the fundamental study in the laboratory instead of full scale roller rig which is not cost effective and inconvenient to achieve diverse design parameters. But the technique for the design of the small scale simulator about the dynamic characteristics of the wheel-rail system and the bogie system has not been well developed in Korea. Therefore, the research using the small-scaled derailment simulator and the 1/5 scaled bogie has been conducted. In this paper, we did running stability test of 1/5 scaled bogie using small-scaled derailment simulator. Also, for the operation of the small scaled simulator, it is required to investigate the performance and characteristics of the simulator system. This could be achieved by a comparative study between an analysis and an experiment. This paper presented the analytical model which could be used for verifying the test results and understanding of the physical behavior of the dynamic system comprising the small- scaled derailment simulator and the 1/5 scaled bogie.

• Korean Journal of Applied Biomechanics
• /
• v.18 no.4
• /
• pp.171-177
• /
• 2008

This work intends to investigate the effects of pedaling directions on the muscle actions during the bicycle's uphill propulsion. A test rig was developed that consists of a bicyle with a special planetary geartrain, a height-adjustable treadmill, a rear-wheel support and a magnetic brake. A three-dimensional motion analysis was performed for measuring kinematic characteristics of the forward backward pedaling and the electromygraphy(EMG) measurements were simultaneously performed for estimating the muscle actions of the leg. In this work, four muscles are considered including Gastrocnemius muscle(GM), Vastus lateralis(VL), Tibialis anterior(TA) and Soleus(SOL) while the uphill slope is varied from $0^{\circ}$ to $6^{\circ}$. Raw EMG signals were first processed through the root-mean-square(RMS) averaging and then ensemble curves were derived by averaging the EMG RMS envelopes over 50 consecutive cycles. Results show that both the kinemactic characteristics and the muscle actions are significantly affected by the pedaling direction. The crank speed of the forward pedaling is higher but the difference in speed is reduced as the slope is increased. The ensemble curves of the :ac signals clearly exhibit some differences in their patterns, peak values and the corresponding locations with respect to the crank angle. The peak values of most EMG signals are higher for the forward pedaling regardless of the slope magnitude. However, the averages of the EMG signals are not observed to have a similar relationship with the pedaling direction, which seems to be affected by several factors such as less experience of the participants' backward pedaling. inappropriate bicycle design for the backward pedaling. These limitations will be further considered in future work.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.6
• /
• pp.476-484
• /
• 2017

The purpose of this paper is to verify the structural integrity of a region with numerous penetration-holes in offshore structures such as semi-submersible rig and FPSO. In order to effectively check the yielding and buckling strength of plate members with penetration-holes, a screening analysis program was developed with the FE analysis tool to generate fine meshed model using the theoretical and analysis methods. When a hole is appeared in the plate structure members, the flow of stress is altered such that concentrations of stress form near the hole. Stress concentrations are of concern during both preliminary and detail design and need to be addressed from the perspectives of strength. To configure the geometrical shape, very fine meshed FE analysis is needed as the most accurate method. However, this method is practically impossible to apply for the strength verifications for all perforated plates. In this paper, screening analysis method was introduced to reduce analysis tasks prior to detailed FE analysis. This method is applied to not only the peak stress calculation combined stress concentration factor with nominal stress but also nominal equivalent stress calculation considering cutout effects. The areas investigated by very fine meshed analysis were to be chosen through screening analysis without any reinforcements for penetration-holes. If screening analysis results did not satisfy the acceptance criteria, direct FE analysis method as the 2nd step approach were applied with one of the coarse meshed model considering hole or with the very fine meshed model considering the hole shape and size. In order to effectively perform the local fine meshed analysis, automatic model generating program was developed based on the MSC/PATRAN which is pre-post FE analysis program. Buckling strength was also evaluated by Common Structure Rule (CSR) adopted by IACS as the stress obtained from very fine meshed FE analysis. Due to development of the screening analysis program and automatic FE modeling program, it was able to reduce the design periods and structural analysis costs.

• Journal of Broadcast Engineering
• /
• v.14 no.6
• /
• pp.661-675
• /
• 2009

The carelessly and illegally copied contents are raising serious social problem as internet and multimedia technologies are advancing. Therefore, development of video copy detection system must be settled without delay. In this paper, we propose the hierarchical video copy detection method that estimates similarity using statistical characteristics between original video and manipulated(transformed) copy video. We rank according to luminance value of video to be robust to spacial transformation, and choose similar videos categorized as candidate segments in huge amount of database to reduce processing time and complexity. The copy videos generally insert black area in the edge of the image, so we remove rig black area and decide copy or not by using statistical characteristics of original video and copied video with center part of frame that contains important information of video. Experiment results show that the proposed method has similar keyframe accuracy to reference method, but we use less memory to save feature information than reference's, because the number of keyframes is less 61% than that of reference's. Also, the proposed method detects if the video is copied or not efficiently despite expansive spatial transformations such as blurring, contrast change, zoom in, zoom out, aspect ratio change, and caption insertion.

• Journal of Broadcast Engineering
• /
• v.17 no.6
• /
• pp.964-975
• /
• 2012

Recently the attention on digital hologram that is regarded as to be the final goal of the 3-dimensional video technology has been increased. A digital hologram can be generated with a depth and a RGB image. We proposed a new system to capture RGB and depth images and to convert them to digital holograms. First a new cold mirror was designed and produced. It has the different transmittance ratio against various wave length and can provide the same view and focal point to the cameras. After correcting various distortions with the camera system, the different resolution between depth and RGB images was adjusted. The interested object was extracted by using the depth information. Finally a digital hologram was generated with the computer generated hologram (CGH) algorithm. All algorithms were implemented with C/C++/CUDA and integrated in LabView environment. A hologram was calculated in the general-purpose computing on graphics processing unit (GPGPU) for high-speed operation. We identified that the visual quality of the hologram produced by the proposed system is better than the previous one.

• Journal of KSNVE
• /
• v.6 no.1
• /
• pp.107-114
• /
• 1996

The damping characteristics of a cylindrical structure containing oil and bearing balls is investigated for external bending forces. The experimental data obtained through the use of bearing balls with viscous oil in a column is given and analyzed. The viscous action of the oil and inertia effects of the balls on the inside of column create a drag force. The drag force dampens the vibration of the column. This study aims to search for an optimum combination of oil and balls which would produce maximum damping. Machining oils of various viscosities along with ball bearings of various sizes place inside cantilevered aluminium tubes of various diameters to create a rig on which the damping properties of the oil and balls can be studied. The contileved tubes are studied in both horizontal and vertical positions in order to gauge the effect of gravity on the system. The actions of the ball in the column and damping characteristics are investigated according to the dimensionless terms. The Buckingham theorem is used to reduce the variables and to predict the damping of an oil ball column. Though the damping ratio remains fairly constant in the horizontal position of column, the damping ratio begins to increase as the ratio of the number of balls and column length rise above 0.28 in the vertical position of oil ball column. The ratio of the ball diameter to column diameter influences the damping ratio with an optimum diameter ratio. Slenderness ratio and gravity effects on the damping ratio ane investigated.

• Proceedings of the Korean Society for Food Science of Animal Resources Conference
• /
• 2005.05a
• /
• pp.247-252
• /
• 2005

본 연구는 파슬리 등의 야채를 첨가하여 제조되는 화이트소시지의 물성 및 저장성에 미치는 자두 분말의 효과를 조사하기 위해 실시되었다. 물성의 변화로서 pH는 자두의 첨가율이 증가함에 따라 상대적으로 감소 하였는데 3% 첨 가시 전 저장 기간 중 가장 낮게 ($pH\;5.11\;{\sim}\;4.44$) 나타났다. 육색(meat color)은 자두의 첨가량에 비례하여 적색도(redness)를 나타내는 a-value에서 높게 나타났으며 명도 (light ness)를 나타내는 L-value에서는 상대적으로 낮은 수치를 보여주었다. 전단력(Shear stre ngth) 측정에서는 저장 기간 중 자두 분말의 첨가량에 비례 하여 근소한 차이를 나타냈는데 저장 7일째에서 가장 높았다. 자두 분말 첨가구 에서의 다소 높은 전단력의 결과는 보수력 (WHC) 측정 에서도 같은 경향을 나타내었는데 자두 분말의 증가량에 따라 3% 첨가구가 대조구 (0%)보다 낮게 나타나 약한 보수성을 보여 주었다. 저장성에 미치는 결과로서 총세균수의 측정결과 저장 3일이 경과한 구간에서 Sorbic acid (0.07%)의 첨가구와 자두 분말(3%) 첨가구 에서 비슷한 항균 효과를 나타내었다. 이 같은 동일한 수준의 항균 효과는 저장 9일째에도 같은 경향으로 나타났다. VBN 측정에는 저장 기간에 따라 증가된 수치를 나타냈는데 저장 7일 및 8일, 9일째 측정 결과는 3% 자두분말 첨가구와 0.07% Sorbic acid 첨가구 와 비슷한 수준을 나타내어 동일한 저장효과를 보여 주었다. 관능검사 실시 결과 총체적인 풍미에 있어서는 자두 분말 첨가구 1.5%가 가장 우수 했으며 다음으로는 3%, Sorbic acid 첨가구 및 공시료 순으로 나타났다.간에 유의차는 나타나지 않았다.pm을 spiking한 후 SPE상에서 SCX(Strong cation exchange column)을 통한 clean-up과정을 거친 후의 STP의 limit of quantification(LOQ)는 약 0.44ppm이었으며, 이에 대한 회수율은 89.7${\pm}$2.3%(n=6)를 나타냈다. 실제 CODEX에서 권장한 우유의 MRL이 0.6ppm인 점을 감안하면 CODEX권고치에 도달할 수 있는 것으로 판단되었다. 따라서 본 연구에서 개발 된 시험법은 지금까지 국내적으로 STP에 대한 시험법이 확립되어 있지 않은 것으로 이와 아울러 간편한 parallux와 병용해 STP에 대한 정량 및 정성 분석을 유도체화 장치 및 형광검출기를 이용해 잔류항생물질 STP에 대한 분석시험법을 개발하였다.화와 네트워크 조직망 구축을 위한 지역중심의 복합 생활문화 공간이 필요할 것이며, 이를 촉진키 위한 mentor academy시스템 접근을 통해 점점 고령화되어 가고 있는 재래시장에 대해 차별적 특성이 반영된 종합적이고 체계적 접근 방법연구가 필요하다./TEX> 자체기술개발, 선진기술 도입, 산업간 및 산업내 기술확산, 국제기술협력 ${\rightarrow}$ 기술혁신의 촉진 ${\rightarrow}$ 총요소생산성과 기업경쟁력(자원 및 역량, 프로세스 경쟁력, 품질경쟁력, 시장경쟁력, 고객성과, 시장성과, 재무성과)의 제고 ${\rightarrow}$ 가격경쟁력(임금, 금리, 물류비용, 환율 등)과 비(非)가격경쟁력(디자인, 에프터서비스, 품질, 운송 등)의 제고 ${\rightarrow}$ 국가경쟁력의 제고 ${\rig