• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1994.10a
• /
• pp.103-112
• /
• 1994

Various kinds of fatigue failures of ocean structures were reported and the importance of fatigue life estimation at the design state is significantly recognized and various kinds of analysis approaches have been discussed. In this paper characteristics of the simplified method proposed here and the spectral method are studied and the elements of the approach are discussed. The merits and demerits of the forementioned analysis schemes are studied and the relating parameters such as SCF and S-N curves are also investigated. The simplified fatigue analysis approach and tile spectral fatigue analysis technique is applied for the analysis of bracing members of typical semi-submersible drilling rig structure for the verification of the usage of two methods and the sensitivity study has been performed using the simplified method. The result from the spectral analysis give a more realistic picture of the fatigue life of the offshore structure considered here.

• Journal of Industrial Technology
• /
• v.21 no.B
• /
• pp.117-123
• /
• 2001

In a modern control field, a control engineer who has theoretical backgrounds with some practical knowledge is demanded. That is to say, an engineer who can understand and operate the various parts such as modeling, simulation, system analysis, signal processing, statistics, and hardware is required. In order to prove the theoretical backgrounds and operate various hardwares, a lot of experimental devices for students are designed in universities. Since the conventional experimental devices are manufactured abroad and the prices of the devices are too high, it is difficult to have. If a low cost experimental device can be developed, it will be very useful for a control engineering education. In Ibis paper, an experimental rig which has two control inputs and three sensor outputs to control the end point of a flexible beam is designed and manufactured. This rig can be used for a control field education.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.5
• /
• pp.675-683
• /
• 2018

In this paper, we have proposed a design and verification methods of electrical system and power loads for unmaned aeriel vehicles(UAVs) through electrical load analysis. In order to meet a UAV system requirement and electrical system specifications, we have designed an electrical power system for efficient power supply and distribution and have theoretically analyzed the power loads according to the power consumption and power bus design of UAV. Using electrical system rig, the designed electrical power system has been experimentally verified. Also, we have performed several flight tests to verify the UAV electrical system and power loads. It is concluded that the proposed design and verification method of electrical system for UAV system.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.341-348
• /
• 2001

The purpose of present study is to investigate for reducing pressure fluctuations in the case of installing the air-shafts on the side wall of the tunnel with small cross-sectional area on conventional line. Experiments were performed with a 1/61-scale moving model rig for the tunnel of 0.764 km length in the condition of tunnel cross-section area of $28 m^2$. According to the results, the maximum pressure fluctuation is reduced by 45 % for 19 air-shafts. This results have the speed-up effects of about 33.4 km/h for the train running in tunnel.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.9
• /
• pp.2181-2190
• /
• 1993

An electro-hydraulic controlled rig type CVT(Continuously Variable Transmission) system was developed and its performance tests were carried out for the optimal operation. A CVT map was suggested based on the speed ration-axial force-torque relationship which was derived from the metal belt CVT mechanics. Also, a real time control and operation software was developed for the electro-hydraulic CVT system. By using the software and the CVT map, the control system was designed for the CVT speed ratio control with various drive modes. The electro-hydraulic CVT system developed in this study showed that the optimal operation algorithm could be obtained for the best fuel economy or the maximum power mode.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.6
• /
• pp.229-235
• /
• 1996

The tapered leaf spring is regarded as the adequate tool to improve ride quality and to reduce vehicle weight of commercial vehicles. These effects are due to minimizing the contact area of each leaf by reducing the number of leaves and by optimizing the thickness profile of each leaf. But in adapting the tapered leaf spring to improve ride quality, we often have some problems of bad pitching and bouncing motion. This paper shows the basic properties of tapered leaf spring by rig tests and how to improve ride quality of a vehicle with tapered leaf springs, compared with multi-leaf spring. From the results of vehicle tests and rig tests it is concluded that the ride quality was effected by the dynamic spring rate and the friction of the tapered leaf spring.

• The KSFM Journal of Fluid Machinery
• /
• v.1 no.1 s.1
• /
• pp.58-63
• /
• 1998

To investigate turbine flow fields under realistic conditions, a rotating turbine test facility has been developed at the Inha University Propulsion Laboratory. The experimental facility consists of an air inlet, settling chamber, single turbine stage test section, and diffuser. This turbine has a design flow coefficient of 0.55 and work coefficient of 1.88. The turbine test rig has four features. First, a large scale test section improves space resolution. Second, low speed rpm enhances safety and reduces required power, Third, DC motor/generator is able to regenerate blower power. Fourth, various types of experiment can be carried out.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.178-183
• /
• 2004

For developing fatigue design curve of cast stainless steels that would be used in piping material of domestic nuclear power plants, a low-cycle fatigue test rig was built. It is capable of performing tests in pressurized high temperature water environment of PWR. Cylindrical specimens of CF8M were used for the strain-controlled environmental fatigue tests. Fatigue life was measured in terms of the number of cycles with the variation of strain amplitude at 0.04%/s strain rates. The disparity between target length and measured length of specimens was corrected by using finite element method. The corrected test results showed similar fatigue life trend with another previous results.

• Tribology and Lubricants
• /
• v.26 no.4
• /
• pp.224-229
• /
• 2010

A new test rig is presented to measure friction losses at journal bearings in a reciprocating compressor. This rig consists of a test bearing, torque sensor, driving motor and loading parts especially for vertical shaft. Friction losses are obtained by measuring torque between motor and test bearing. The experiments are carried out at several rotational speeds and temperatures. The test results are presented and discussed.

• Transactions of Materials Processing
• /
• v.7 no.1
• /
• pp.49-58
• /
• 1998

In this paper the bending collapse characteristics of 6XXX series aluminum rectangular tubes were studied with a pure bending collapse test rig which could apply the pure bending moment without imposing additional shear and tensile forces. Under the pure bending moment, there occured three kinds of bending collapse modes-local buckling delayed buckling and tensile failure-depending on the a, b, t (depth width thickness) and material properties. Experimental results are compared with the results of finite element method and other methods.