• 한국HCI학회:학술대회논문집
• /
• 2007.02a
• /
• pp.739-743
• /
• 2007

In this paper, a stereoscopic display system using a rotary disk type beam shutter and two beam projectors is proposed. It is a kind of active stereoscopic display and can be easily converted from passive stereoscopic system using polarizing filters. If it is possible to synchronize the revolution speed of the beam shutter with the integer multiple of the scanning frequency of the beam projectors, we can obtain a comparable performance with our system to an active stereoscopic system using one expensive high performance beam projector. Further, if we rotate the beam shutter at sufficiently high revolution speed, our active stereoscopic system works regardless of synchronization and thus the system is much easier to implement.

• Journal of Biosystems Engineering
• /
• v.27 no.4
• /
• pp.301-310
• /
• 2002

With a purpose to manufacture an onion peeler, the root cutting equipment of the onion could be attached to a prototype onion peeler was developed. Before the experiment, the distribution of the dimensions of the Korean native onion were measured. And some types of the blades to cut and remove the root of the onion were designed and such characteristics as feasible revolution, conveying speed, and power requirement were investigated. From the result of the test, the selected one among the various cutters was the wing type blade with the round blade to cut out the root and with the vertical blade to cut a circular line. The optimum operating conditions of the wing type blade were revealed the revolution with no load was at 630 rpm, and the conveying speed was 0.08 m/s. Under these conditions, the maximum torque was 5.25 kg·m and the power requirement was 33 W, respectively.

• Wind and Structures
• /
• v.7 no.5
• /
• pp.305-316
• /
• 2004

In this study, a wind tunnel, that has been developed for experiments of wind turbine rotor blades, has been considered. The deviations of the measurements have been examined after this wind tunnel had been introduced and the measurements on it had been explained. Two different wind turbine rotor blades miniatures have been used for getting better results from the experiments. The accuracy of measurements have been experimented three times repetitively and examined statistically. As a result, wind speed values which this type of wind tunnel and wind turbine rotors need for starting, wind speed in the tunnel, temperature and moisture values, the number of rotor's revolution, and the voltage that is produced in 102 ${\Omega}$ resistance and current values have been determined to be fixed by measurements used. This type of wind tunnel and wind turbine rotor' performance difference and the difference of revolution figures have been determined to be fixed by measurements used.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.19 no.1
• /
• pp.1-16
• /
• 2020

With the advent of the fourth industrial revolution era, there has been a growing interest in deep learning using big data, and studies using deep learning have been actively conducted in various fields. In the transportation sector, there are many advantages to using deep learning in research as much as using deep traffic big data. In this study, a short -term travel speed prediction model using LSTM, a deep learning technique, was constructed to predict the travel speed. The LSTM model suitable for time series prediction was selected considering that the travel speed data, which is used for prediction, is time series data. In order to predict the travel speed more precisely, we constructed a model that reflects both temporal and spatial effects. The model is a short-term prediction model that predicts after one hour. For the analysis data, the 5minute travel speed collected from the Seoul Transportation Information Center was used, and the analysis section was selected as a part of Gangnam where traffic was congested.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.895-898
• /
• 2001

This paper presents an optimization cutting speed(OCS) program developed to improve the machining precision and tool life in high speed machining using ball end milling. This program optimized the cutting speed that is changing at any time in free surface machining of an automobile part like a connecting load die. The technique of optimization cutting speed makes the CAD/CAM-generated NC code go through a reverse post process, conducts cutting simulation, and obtain the effective tool diameter of the ball end milling. Then it changes the spindle revolution to within the range of critical cutting speed fit for the material of the workpieces depending upon the effective tool diameter. In this study, the machining precision and tool life were compared for the two connecting load dies processed using the general cutting method and the proposed optimization cutting speed technique, respectively.

• Journal of Biosystems Engineering
• /
• v.23 no.5
• /
• pp.445-456
• /
• 1998

This study was carried out to evaluate the performance of a medium scale rice polisher of 2.5 t/h and to improve its performance for producing the clean rice with high quality. The maximum internal pressure, broken rice ratio. whiteness in the rice polisher were investigated, and the effects of outlet resistance, water spraying rate, shaft revolution speed and rice moisture content on the polishing performance were analyzed to find out proper operating conditions. The conclusions of this study were as follows: 1. In the performance evaluation of the polisher, the broken rice ratio increment of 0.1%, the max. internal pressure of about 11 N/${cm}^2$, and whiteness increment of 2.2~3.7 resulted at the conditions of 20 PS driving power, 950 rpm, 150 cc/min water spraying rate, 44.1 Nㆍcm outlet resistance and about 15% rice moisture content. 2. Though max. internal pressure and whiteness at the 17% rice moisture content were higher than those at the 15% moisture content under the same operating conditions of the polisher, but the broken rice rate at the 17% moisture content was absolutely low compared with that at 15% moisture content. The water spraying effect to reduce broken rice and to increase whiteness was much significant at the 15% moisture content not significant at 17% moisture content. 3. The main parameter of the performance was outlet resistance, and low resistance of about 44.1 Nㆍcm was recommended at the polisher. 4. The proper water spraying rate in the polisher was about 150 cc/min. 5. As the shaft revolution speed decreased from 950 rpm and 800 rpm to 650 rpm, the broken rice ratio increased and whiteness decreased. 6. As the driving power of the polisher increased from 20 PS to 30 PS, the max. internal pressure decreased by about 1~2.5 N/${cm}^2$ and whiteness increased by about 1~2, but the broken rice rate was not changed. 7. The proper operating conditions of the polisher seemed to be the revolution speed of 800-950 rpm, the water spraying rate of about 150 cc/min, the oulet resistance of about 44.1 N.cm and 30 PS driving power.

• Journal of Biosystems Engineering
• /
• v.29 no.2
• /
• pp.121-130
• /
• 2004

This study was carried out to develop a miller to produce white embryo rice with functional nutrients by improving the conventional vertical miller. The effects of rice moisture content and the shaft revolution speed of the miller on germ(embryo) adherence rate, whiteness, broken rice rate, and cracked rice rate were investigated. Also, the effect of the mesh size of emery stones on the germ adherence rate was investigated. The vertical prototype miller was improved with the increasement of about 42% in producing white embryo rice at proper conditions(shaft revolution speed of 900 rpm, emery stones of mesh ＃50, processing capacity of 2.3t/h, zero outlet resistance, rice moisture content of 16.2%). The results were as follows: 1. The germ adherence rate of white rice was significantly influenced by the moisture content of brown rice. The germ adherence rate of white rice decreased rapidly with the increase of the moisture content of brown rice. When brown rice with moisture content of 13.2%, 14.5%, 15.2%, 15.4% was milled by the prototype with emery stones of mesh ＃35 and shaft speed of 900(1,100) rpm, rpm adherence rate of milled rice was 76.2%(70%), 69.2%(66%), 45.9(38%), 13.0(9%), respectively. 2. The whiteness of white rice milled by the prototype with emery stones of mesh ＃35 and shaft speed of 1,100(900)rpm increased from 27(23) to about 40, respectively, as the moisture content of brown rice increased from 13.2% to 17.2%. 3. The rate of broken rice of white rice milled at 900rpm decreased by 0.6∼1.0% compared with that at 1,100rpm when the moisture content of brown rice was less than 15.2%. 4. The germ adherence rate was increased by 10.3% and 11.0%, respectively when brown rice with moisture content of 16.2% and 15.5% was milled by the prototype miller with shaft speed of 900rpm and emery stones of mesh ＃50 instead of mesh ＃35. 5. Considering the germ adherence rate, broken rice rate, and whiteness of milled rice, the proper milling conditions of the prototype miller for producing embryo rice were the moisture content of about 15%, the processing capacity of 2.3t/h and minimum outlet resistance of 0Nㆍm with shaft speed of 900rpm and emery stones of mesh ＃50.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.476-478
• /
• 1997

A new speed detection method using low resolution incremental encoders, especially excellent in the low speed region and in the transient state, is proposed. The half period error of an incremental encoder is greater than the period error. So it's not recommended to quadruple the number of pulses per revolution, because it increase the ripple of speed. To overcome this restriction a speed detection, method has been proposed. But it requires so many latch circuits. Therefore we propose a new speed detection method that has different concept and has fewer latch circuits.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.742-747
• /
• 1998

In the High-Speed range for salient type synchronous reluctance motors, the effect of iron loss can not be negligible. In this paper, the SynRM without cage is analyzed mathematically to model and the speed control system is examined by simulation. In order to control the revolution speed, a closed-loop control with vector control and decoupling control are applied to the high-speed SynRM drives. The speed control system is analyzed to investigate the desired speed characteristics of high SynRM by simulation.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.266-272
• /
• 2002

High-speed machining is one of the most effective technology to improve productivity. Because of the high speed and hugh fried rate, high-speed machining can alive great advantages for the machining of dies and molds. This paper describes on the improvement of machining accuracy in high-speed machining. Depth of cut, feed rate and spindle revolution are control factors. The effect of the control factors on machining accuracy is discussed fur the results of surface roughness and machining error in Z-direction of the high speed machining.