• 신재생에너지
• /
• 제10권4호
• /
• pp.9-15
• /
• 2014

In this study pressure and shaft torque pulsation were measured with variation of head and flow during the model test for a 15 MW Francis Turbine. Pressure pulsations were measured at the inlet of the spiral casing and 4 points in the cone of the diffuser and shaft torque pulsation at the upper position of the turbine. The maximum amplitude of pressure pulsation appeared 2.03% of the maximum rated head with the frequency of 25% of the rated revolution and at the guide vane opening of $10^{\circ}$. Shaft torque pulsation appeared 0.01% of the rated shaft torque, fairly low value. Air was admitted through the cone and pressure pulsation gradually decreased with increase of air flow and kept nearly constant after 5% of the rated flow. A new Francis turbine of which specific speed is 115 m-kW had been designed to rehabilitate the old one and the model test was performed at EPFL. The commercial code, STAR-$CCM^+$ was used for numerical simulation of flow.

• 한국정밀공학회지
• /
• 제19권3호
• /
• pp.144-151
• /
• 2002

This work focuses on finding out the noise source and the method of reducing the noise level of LPG(liquefied petroleum gas) fuel injector. The noise of LPG injector in operating condition is due to the impact between valve and valve seat. This study shows that if the revolution of engine is increased, the noise of LPG injector will be more serious but it is not nearly affected by the increment of fuel pressure. The source and transmission paths of noise are identified through the analysis of noise generation mechanism and noise spectrum. The sound absorbing material is tested to verify its efficiency of sound absorption thor the LPG injector. The effect of noise reduction of absorbing material is remarkable when the engine speed is high. Consequently two methods of reducing the noise level are suggested from the identified results. The one is to equip the absorbing material on the outer side of injector and the other is to coat with a soft material or equip a soft ring on the surface of impact.

• 소성∙가공
• /
• 제27권3호
• /
• pp.145-153
• /
• 2018

Magnesium material could be widely used in the automotive industry because of its high strength to weight ratio, but the electric resistance spot welding process of magnesium sheets is difficult because of its low electric resistance and high thermal conduction and thermal expansion. For this reason, an electric resistance surface friction spot welding process using rotating dies is suggested for the spot welding of magnesium metal sheets. This welding method can be characterized by three heating methods: (1) electric resistance heating on contacted surface, (2) surface friction heating by rotating dies, and (3) thermal conduction heating from heated steel electrodes, for the fusion of metal at the interfacial zone between the two magnesium sheets. This welding process also has variables to explore, such as welding currents, diameters of the steel electrode, and rotating dies. It was found that the welding strength could reach industrial requirements by applying a welding current of 11.0kA, with steel electrodes of 12mm diameter, with rotating dies of 4.4 mm diameter, under the condition of a revolution speed of 1200rpm of rotating dies, for the surface friction spot welding process of AZ31 magnesium alloy sheets of 1.4mm thickness.

• 산업기술연구
• /
• 제26권A호
• /
• pp.39-46
• /
• 2006

As an automobile fuel, LPG has many environmental advantages compared to gasoline or diesel. However, current LPG engine which is provided with LPG fuel as gas form has lower power and worse fuel efficiency than gasoline engine. These problems of low power and bad fuel efficiency come from lower volumetric efficiency. Also there is a new rising problem of high failure ratio in an engine emission test. Although there are many factors which affect engine performance of exhaust gas emission, one believes that the fact that ECM of gasoline engine is used for LPG engine when retrofitting gasoline engine to LPG engine is one of the main problems, which lower engine power and emit more noxious gas due to wrong ignition timing. To solve these problems, one studied the effects of ignition timing on the exhaust gas to find out the optimum condition of ignition timing. The experimental results show that noxious exhaust gas is reduced and engine power is increased if the optimum control of ignition timing is applied in accordance to the revolution speed of engine.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 추계학술대회 논문집 학회본부
• /
• pp.282-284
• /
• 1997

Ultrasonic motors using piezoelectric ceramics and brass metal endcaps were fabricated, which is operated by single - phase high frequency. The structure of the ultrasonic motors has the wind-mill type. The stator part consists of a piezoelectric disk and two metal endcaps slotted wind-mill type. According to the piezoceramic disk vibrates as a radial mode, two metal endcaps provide both longitudinal and torsional displacements simultaneously. Because the metal endcaps have a nonsymmetric structure. the principle of the ultrasonic motor is not well understood. The dimension of the ultrasonic motor is diameter in 12.7 mm and thickness in 2.0 mm, and especially the PMN-PT-PZ piezoelectric disk was used. The maximum revolution speed 700 rpm and the maximum torque 0.22 mN.m were obtained. The ultrasonic motor for rotation was Supplied only single phase AC.

• Journal of Mechanical Science and Technology
• /
• 제19권spc1호
• /
• pp.336-342
• /
• 2005

The DC motor of a vehicle may cause noise and vibration due to high-speed revolution, which can make a driver feel uncomfortable. There have been various studies attempting to solve these problems, mostly focusing on the causes of noise and vibration and a means of preventing them. The CAE methodology is more efficient than a real test for the purpose of looking for various design parameters to reduce the noise and vibration of the DC motor. In this study, a design process for reducing brush noise is presented with the use of a computer model, which is made by using a multi-body dynamics program (DADS). The design parameters to reduce the brush noise and vibration were proposed using a computer model. They were used to reduce the noise and vibration of the DC motor and verified by the test results of the fan DC motor in the vehicle. This method may be applicable to various DC motors.

• 한국기계가공학회지
• /
• 제16권1호
• /
• pp.90-95
• /
• 2017

Recently, smaller and lighter products have become of interest in industry applications that increasingly demand thin plate joints of thickness 1.0 mm or less using friction stir welding. In this study, high frequency spindles that run at 3,500-6,500 rpm are introduced for thin friction stir-welded plates. Weldability tests are performed for the butt-joint method of Al5052-H32 alloy of 1.0 mm thickness under 3,500-6,500 rpm spindle revolution with 250-400 mm/min feed speed. An optical microscope was used to analyze the bid structure of the welded zone and stir zone. The tensile-strength and hardness of the welded zone were then measured.

• 한국생산제조학회지
• /
• 제24권1호
• /
• pp.69-74
• /
• 2015

This study examined the fluid flow characteristics of a hydraulic retarder adapted as an auxiliary brake for heavy vehicles. The commercial computational fluid dynamics (CFD) software STAR-CCM+ was used to investigate the torque performance and flow characteristics of the hydraulic retarder. The numerical results showed that the pressure distribution was higher near the inner wall surface of the rotor and stator. The pressure of the working fluid increased in the radial direction of the rotor and stator. The variation in the fluid velocity intensity showed a similar trend to that of the fluid pressure, but the maximum velocity appeared near the outer wall surface of the rotor and stator interface. The numerical results showed that increasing the revolution speed of the retarder greatly increased the rate of torque generation.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.414-417
• /
• 2001

Recently, developments of device using characteristics of ceramics as a new technical material is in progress. While doing so, Ultrasonic motor which is a part of research & development of piezo-actuator by piezo-effects is being used in the various applications. So, we fabricated a flat-type $L_{1}-B_{8}$ mode Ultrasonic motor and measured the operation characteristics of its. The size of USM is 80*20*1.5[$mm^{3}$](length*width*thickness) and is constructed with stator by piezo-ceramics and stainless elastic body and rotator by bearings. As results of experiments, the fastest speed of revolution(v), the maximum torque(T) and the efficiency( $\eta$ ) were 37.5[cm/sec], 5.0[ $mN{\cdot}m$ ] and 1.17[%] respectively when 27.9[kHz], 150[gf], 50[V] were applied. So, we think this $flat-type_{1}-B_{8}$ mode Ultrasonic motor is able to be used for applications in forwarding device of a paper or electric card and so on.

• 한국자동차공학회논문집
• /
• 제16권3호
• /
• pp.52-59
• /
• 2008

Most accident reconstruction or analysis depend on the coefficient of friction to estimate the vehicle speeds. Skid mark and coefficient of friction are usually utilized to calculate the velocity and behavior of vehicles. For a critical case such as traffic accident reconstruction, however, the initial velocity of the car should be calculated precisely. In this paper, emergency brake tests on ABS and Non-ABS brake system are conducted on the dry pavement asphalt road on speed 40, 60, 80 and 100 km/h respectively. The SWIFT sensor was established in the front wheel and rear wheel at driver side to measure the forces, moments and speeds of revolution of the tires. These tests results can be available to brake tests and accident reconstruction.