• 한국공작기계학회논문집
• /
• 제17권1호
• /
• pp.7-15
• /
• 2008

Currently existing high-accuracy and high-speed die sets used in reciprocal press create scratches at the surface of guide posts, steel balls, and bushes due to vertical movement of balls with point-contacts between inner surface of bushes and guide posts. Consequently, accuracy of the die set and the life span of the metal mold are reduced. However, those scratches could reduce the pre-load of the steel ball. This research designed and developed a groove-type die set which improves life span of the die set by eliminating point-contacts of steel balls with guide posts. The guide post consisted of a steel-ball retainer, a steel-ball retainer stopper, a guide bush, a guide pin, a snap ring, and a spring. The steel-ball retainer has 72 holes with 8 columns of 9 holes in each column. The inner surface of the guide bush was grinded(surface roughness: $Ra\;\\;0.2{\mu}m$, accuracy: $0\;{\sim}\;-0.002mm$) after NC turning and heat treatment. Also, a line of small intermediate pocket was processed inside of the guide bush for lubrication and elimination of foreign materials. Guide grooves of steel balls were processed using a wire EDM(Electrical Discharge Machining) after heat treatment. With such a design of the guide post stated above, loads against steel balls could be dispersed greatly by the line contacts through the guide groove between the guide post and the guide bush, and the life span of the guide post could be expanded semi-permanently.

• 대한치과교정학회지
• /
• 제39권6호
• /
• pp.402-419
• /
• 2009

성장이 종료된 치성 또는 골격성 개방교합 환자를 치료하는 것은 매우 어려운 일이다. 전치부 개방교합 환자는 증가된 전안면고경, 상악 구치부의 과도한 수직성장, 큰 하악각 등의 특징을 지닌다. 이러한 증례에서 구치의 압하를 통한 개방교합의 해소는 좋은 치료전략이다. 본 연구는 교정용 미니임플란트를 이용하여 개방교합을 치료하고 성공적인 유지를 얻은 두 명의 환자에 대한 보고이다. 적절한 진단이 시행되고 교정용 미니임플란트 등의 장치를 이용한 치료기법을 적용하면 수술치료 없이 교정치료만으로 개방교합의 치료가 가능하며, 하악구치부에 posterior bite block을 추가한 가철식 유지장치 및 SFR이 개교환자를 위한 유지장치 또는 보조유지장치로 유용하게 사용될 수 있다는 결론을 얻었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.482-483
• /
• 2009

In chemical mechanical planarization (CMP) process, the uniformity of stress acting on wafer surface is a key factor for uniform material removal of thin film especially in the oxide CMP. In this paper, we analyze the stress on the contact region between wafer and pad with finite-element analysis (FEA). The setting pressure acting on wafer back side was $500g/cm^2$ and the retainer pressure was changed from 300 to $700g/cm^2$. The polishing test is also done with the same conditions. The material removal rate profiles well-matched with stress distribution.

• 대한치과교정학회지
• /
• 제35권4호
• /
• pp.295-301
• /
• 2005

• 대한치과교정학회지
• /
• 제41권1호
• /
• pp.51-58
• /
• 2011

Objective: To evaluate the shear bond strength (SBS), fracture mode, wire pull out (WPO) resistance and microleakage between low-shrinking and conventional composites used as a lingual retainer adhesive. Methods: A total of 120 human mandibular incisor teeth, extracted for periodontal reasons, were collected. Sixty of them were separated into two groups. To determine the SBS, either Transbond-LR (3M-Unitek) or Silorane (3M-Espe) was applied to the lingual surface of the teeth by packing the material into standard cylindrical plastic matrices (Ultradent) to simulate the lingual retainer bonding area. To test WPO resistance, 20 samples were prepared for each composite where the wire was embedded in the composite materialand cured. Then tensile stress was applied until failure of the composite occurred. The remaining 60 teeth were divided into two groups and multi-stranded 0.0215-inch diameter wire was bonded with the same composites. Microleakage was evaluated by the dye penetration method. Statistical analyses were performed by Wilcoxon, Pearson chi-square, and Mann-Whitney-U tests at p < 0.05 level. Results: The SBS and WPO results were not statistically significant between the two groups. Significant differences were found between the groups in terms of fracture mode (p < 0.001). Greater percentages of the fractures showed mix type failure (85%) for Silorane and adhesive (60%) for Transbond-LR. Microleakage values were lower in low-shrinking composite than the control and this difference was found to be statistically significant (p < 0.001). Conclusions: Low-shrinking composite produced sufficient SBS, WPO and microleakage values on the etched enamel surfaces, when used as a lingual retainer composite.

• Imaging Science in Dentistry
• /
• 제51권1호
• /
• pp.63-71
• /
• 2021

Purpose: The aim of this study was to assess the artefacts of 12 fixed orthodontic appliances in magnetic resonance images obtained using 1.5-T and 3-T scanners, and to evaluate different imaging sequences designed to suppress metal artefacts. Materials and Methods: In vitro, study casts of 1 adult with normal occlusion were used. Twelve orthodontic appliances were attached to the study casts and scanned. Turbo spin echo (TSE), TSE with high readout bandwidth, and TSE with view angle tilting and slice encoding for metal artefact correction were used to suppress metal artefacts. Artefacts were measured. In vivo, 6 appliances were scanned: 1) conventional stainless-steel brackets; 2) nickelfree brackets; 3) titanium brackets; 4) a Herbst appliance; 5) a fixed retainer; and 6) a rapid maxillary expander. The maxilla, mandible, nasopharynx, tongue, temporomandibular joints, and cranial base/eye globes were assessed. Scores of 0, 1, 2, and 3 indicated no artefacts and minor, moderate, and major artefacts, respectively. Results: In vitro, titanium brackets and the fixed retainer created minor artefacts. In vivo, titanium brackets caused minor artefacts. Conventional stainless-steel and nickel free brackets, the fixed retainer, and the rapid maxillary expander caused major artefacts in the maxilla and mandible. Conventional stainless-steel and nickel-free brackets caused major artefacts in the eye globe (3-T). TSE with high readout bandwidth reduced image artefacts in both scanners. Conclusion: Titanium brackets, the Herbst appliance, and the fixed retainer caused minor artefacts in images of neurocranial structures(1.5-T and 3-T) when using TSE with high readout bandwidth.

• 대한치과보철학회지
• /
• 제14권1호
• /
• pp.66-71
• /
• 1976

The purpose of this investigation was to evaluate the mouth preparation and design of removable partial dentures. A total of 187cases for the prefabricated partial denture frameworks in both maxillary and mandibular semi-dentulous situations (66 cases and 203 cases) was selected from this study. The evaluations of mouth preparation and design observed here involved the classification of edentulous spaces, status of abutment splinting with location, design of direct retainer and structure of maxillary major connector according to the incidence of both dental arches, ages, sexes and segment of semidentulousness. The analyzed results were as follows: 1) The order of frequency rate in removable partial denture construction was Class II (50.27%), Class I (36. 90%), Class III (10.69%), and Class IV (2.14 %). 2) The distribution on design of maxillary removable partial denture prosthesis was 33.22% and 64.11% in mandibular removable partial denture prosthesis. 3) The age distribution of removable partial denture prosthesis was prominent after40 years (41.71%). 4) The design pattern of maxillary major connectors was in order of anteroposterior bar, single palatal bar, palatal strap, U-shape connector. 5) The design pattern of direct retainer was in order of Aker's clasp, I-bar clasp, backaction clasp, cuspid universal clasp. 6) The abutment for partial denture clasp splinted between premolar and premolar and its frequency rate revealed 53.44%. 7) It seemed that the location and design of the indirect retainer showed accepatble limit.

• 대한치과보철학회지
• /
• 제38권1호
• /
• pp.59-72
• /
• 2000

This study was performed to investigate the effects of tooth mobility and design of the direct retainer on the stress of supporting tissues in distal extension removable partial denture. Tooth mobility was simulated and four different types of direct retainer such as Alters clasp, I-bar clasp, wrought wire clasp, and Dalbo attachment were designed and stress on the support-ing tissues were measured and analyzed with straingauge method. The following conclusions were drawn from this study. 1. The stress revealed at the lingual side of alveolar bone of the abutment tooth in edentulous area was the largest. 2. The stress at the lingual side of alveolar bone of the abutment tooth in edentulous area was increased according to the increase of tooth mobility in I-bar clasp and Dalbo attachment. 3. The stress at the residual ridge crest was the great in Dalbo attachment on mobility 0, in I-bar clasp on mobility 1, and in wrought wire clasp on mobility 2. 4. There was little changes of stress according to the increase of tooth mobility at buccal and lingual side of the residual ridge crest and around the abutment teeth in dentulous area.

• 대한치과교정학회지
• /
• 제32권2호통권91호
• /
• pp.143-153
• /
• 2002

콤포지트와 여러가닥 강선을 사용하여 제작된 접착식 보정장치는 심미적이며, 효과적인 보정장치라 할 수 있다. 이 연구는 접착식 보정장치의 전단접착강도를 측정하고, 접착식 보정장치의 제작 시 사용하는 여러가닥 강선 및 접착방법의 이상적인 조합을 제시하기 위해 디자인되었다. 교정치료를 위해 발거한 건전한 상하악 소구치 160개를 사용하여 80개의 시편을 제작하였다. 접착면적 및 강선의 길이, 콤포지트의 두께를 동일화하고, 직접접착 및 간접접착의 방법으로 여러가닥 강선을 접착하여 접착식 보정장치를 제작하였다. 만능시험기를 사용하여 각 시편에서의 전단접착강도 및 강선의 탈락시까지의 신장량을 측정하여, 다음과 같은 결론을 얻었다. 1. 6가닥, 0.0155인치의 강선에서 가장 큰 최대 접착강도를 보이고, 3가닥, 0.0195인치의 강선에서 가장 작은 최대 접착강도를 보였는데, 그 차이는 유의할 만큼 크지 않았다(p<0.05). 즉 강선의 직경 및 가닥수는 접착강도와 큰 연관성이 없다. 2. 3가닥, 0.015인치의 강선에서 가장 큰 신장량을 보여 주었고, 3가닥, 0.0195인치 강선에서 가장 작은 신장량을 보여주었다(p<0.05). 강선의 직경이 작을수록 신장량은 크게 나타났으나, 강선의 가닥수는 신장량과 큰 연관성이 없다. 3. 두 가지 접착방법의 비교에서 간접 접착술식을 사용했을 때 더 큰 접착강도 및 신장량을 보여 주었고, 통계적으로 유의한 차이를 나타냈다(p<0.05).

• 대한치과의사협회지
• /
• 제18권8호통권137호
• /
• pp.633-636
• /
• 1980