• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.8
• /
• pp.872-878
• /
• 2014

This paper proposes a measurement method of the complex relative permittivity of semi-solid materials using a new cavity structure. Semi-solid materials are positioned in the proposed cavity where an aperture exists on each corner of the upper part and a ground plane is separated. In order to show the validation of the proposed method, we measured the complex relative permittivity of distilled water and 0.9 % saline by sensing a shift of resonant frequency and using Critical-Points Method, and compared the results with those derived from the Cole-Cole equation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.9 s.351
• /
• pp.64-68
• /
• 2006

Novel system-on-package (SOP) - D technology to improve the mechanical and thermal properties of a MCM-D substrate was suggested. Based on this investigation, the two types of band pass filters for the V-band application with unique structure were designed and implemented using 2-metals, 3-BCB layers. The first type using distributed resonator had the insertion loss below 2.6 dB at 55 GHz and group delay was below 0.06 ns. For the second type with edge coupled structure, the insertion loss and group delay were 3 dB and 0.1 ns, respectively. Suggested MCM-D substrate with band pass filter can be used to evaluate mm-Wave system including flip-chip bonded MMIC.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.10
• /
• pp.964-970
• /
• 2013

This paper presents a bandpass wireless 3-D chip to chip interface technique. The proposed technique uses direct amplitude modulation of the free running oscillator which especially utilizes the coupling capacitance between two stacked chips as a part of the resonator. Therefore, the oscillator is three dimensionally configured and a simple envelope detector can be used as a receiver without any additional matching circuitry. The proposed link was designed and fabricated using 110 nm CMOS technology and experimental results successfully showed the data transmission at a data rate of 2 Gb/s for the stacked chips with a thickness of 50 ${\mu}m$ consuming 4.32 mW. The sizes of the Tx and Rx chips are 0.045 $mm^2$ and 0.029 $mm^2$, respectively.

• Journal of electromagnetic engineering and science
• /
• v.17 no.3
• /
• pp.126-132
• /
• 2017

In this study, we designed, measured, and analyzed a rearranged L-shape magnetic resonance coupling wireless power transfer (MR-WPT) system for practical applications with laptops. The typical four resonator MR-WPT (Tx part: source loop and Tx coil; Rx part: Rx coil and load loop) is difficult to apply to small-sized stationary and mobile applications, such as laptop computers, tablet-PCs, and smartphones, owing to the large volume of the Rx part and the spatial restrictions of the Tx and Rx coils. Therefore, an L-shape structure, which is the orthogonal arrangement of the Tx and Rx parts, is proposed for indoor environment applications, such as at an L-shaped wall or desk. The relatively large Tx part and Rx coil can be installed in the wall and the desk, respectively, while the load loop is embedded in the small stationary or mobile devices. The transfer efficiency (TE) of the proposed system was measured according to the transfer distance (TD) and the misaligned locations of the load loop. In addition, we measured the TE in the active/non-active state and monitor-open/closed state of the laptop computer. The overall highest TE of the L-shape MR-WPT was 61.43% at 45 cm TD, and the TE decreased to 27.9% in the active and monitor-open state of the laptop computer. The conductive ground plane has a much higher impact on the performance when compared to the impact of the active/non-active states. We verified the characteristics and practical benefits of the proposed L-shape MR-WPT compared to the typical MR-WPT for applications to L-shaped corners.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.19 no.5
• /
• pp.20-25
• /
• 1982

A realization method of the microwave oscillator is proposed by the inherently stable transistor with a cavily resonator feedback loop. The real Part of the output impedance of the inherently stable bipolar transistor can be made to be negative at the resonance frequency by the high-Q cavity feedback loop, and the oscillation condition can be obtained with the matching section of the load. In this work the microwave transistor oscillator is realized with a silicon bipolar transistor HXTR 2101 and a reentrani cavity, and characteristic of the output power 10m Watts at 2.33 GHz osc. frequency can be verified experimentally.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.43-46
• /
• 2004

This work is experimental study about a nozzle part in the aerodynamic igniter using only compressible gas. In study, constructions of the aerodynamic igniter using a supersonic nozzle and an aerospike nozzle have been introduced, and experimental results(mainly max. heating temperature characteristics) have been presented. Using of the supersonic nozzle leads to faster and higher temperature in same mass flow, and the aerospike nozzle works in wide variable range of pressure.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.5
• /
• pp.508-517
• /
• 2004

We described a near-field scanning microwave microscope which uses a high-quality dielectric resonator with a tunable screw. The operating frequency is f=4.5 5GHz. The probe tip is mounted in a cylindrical resonant cavity coupled to a dielectric resonator We developed a hybrid tip combining a reduced length of the tapered part with a small apex. In order to understand the function of the probe, we fabricated three different tips using a conventional chemical etching technique and observed three different NSMM images for patterened Cr films on glass substrates. We measured the reflection coefficient of different metal thin film samples with the same thickness of 300m and compared with theoretical impedance respectly. By tuning the tunable screw coming through the top cover, we could improve sensitivity, signal-to-noise ratio, and spatial resolution to better than $1{\mu}m$. To demonstrate the ability of local microwave characterization, the surface resistance of metallic thin films has been mapped.

• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.1
• /
• pp.61-64
• /
• 2001

VCO(Voltage Contolled Oscillator) is one of the main components governing the size, performance and power consumption of telecommunication devices. As the devices become much smaller, YCO need to hove much smaller size with better characteristics. Buried type passive components of L, C, R were developed previously and the structure of these components are good for minimizing the size of VCO. Our own library of passive components is used in simulation and measurement circuit designed by ourselve. In structure of multi-layered VCO, some components governing the characteristics of VCO are selected and placed on the top of oscilltor for the good tuning process. In resonator part, the stripline structure and low loss glass/ceramic material are used to get higher Q value. In our research, a VCO oscillates in the 2.3~2.36 GHz band is developed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.135-138
• /
• 2002

VCO(Voltage Controlled Oscillator) is one of the main components governing the size, performance and power consumption of telecommunication devices. As the devices become much smaller, VCO need to have much smaller size with better characteristics. Buried type passive components of L,C,R were developed previously and the structure of these components are good for minimizing the size of VCO. Our own library of passive components is used in simulation and fabrication of VCO circuit, and surface mounted components like varactor diode are analysed using the measurement circuit designed by ourselves. Two-Dimensional simulation of VCO circuit and local three-Dimensional structure simulation are performed and their relation is obtained. In structure of multi-layered VCO, some components governing the characteristics of VCO are selected and placed on the top of oscillator for the good tuning process. In resonator part, the stripline structure and low loss glass/ceramic material are used to get higher Q value. In our research, a VCO oscillates in the 2.3∼2.36 GHz band is developed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.10
• /
• pp.1648-1655
• /
• 1997

The intake noise, a major source of vehicle noises, has rapidly become a noticeable, and has been studied to reduce the level. Traditionally, the intake system has been developed through a experiment, namely, the trial and error process. This approach requires very high cost and long time consuming to develop the system. Recently, FEM and BEM are becoming useful in analysis of the intake system, and te results of analysis are very valid. But because these techniques also require high cost and long analysis time, these are generally not practical tool at the early stage of the development of an intake system. In this study, the software was developed to predict and analyze the acoustic characteristics of an intake system. It was based on the Transfer Matrix Method and operated to analyze a simplified intake system in a personal computer. It can be used early in the design stage of development of the intake system. This study presented an improvement to reduce the level of an intake noise. It was to select the optimum position of a resonator and verified by NIT/SYSNOISE, FE analysis commercial software, and testing a prototype.