• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.3
• /
• pp.39-43
• /
• 2011

Effects of cavity material on the Q-factor measurement of microwave dielectric materials were studied by HFSS simulation and the measurements using metal cavity. $TE_{01\delta}$ mode resonant frequency was determined from the electric and magnetic field patterns and the loaded Q-factor was calculated from 3dB bandwidth of $S_{21}$ spectrum. When the cavity metal materials were Cu, SUS and Au cavity, the level of Q-factor was similar. However, Q-factor was significantly decreased when the cavity metal material was CuO. The Q-factor measurements of dielectric resonator by network analyzer using various metal cavity exhibits consistent behavior.

• Journal of computational fluids engineering
• /
• v.9 no.1
• /
• pp.1-9
• /
• 2004

Large eddy simulation is used to investigate the compressible flow over a cavity with high aspect ratio. The sub-grid scale stresses are modeled using the dynamic model. The compressible Navier-Stokes equations are solved with the sixth order accurate compact finite difference scheme in the space and the 4th order Runge-Kutta scheme in the time. The buffer Bone techniques are used for non-reflecting boundary conditions. The results show the shear layer oscillation over the cavity. The votical disturbances, the roll-up of vorticity, and impingement and scattering of vorticity at the downstream cavity edge can be seen in the shear layer. Several peaks for the resonant frequencies are found in the spectra of the vertical velocity at the center-line. The most energetic Peak near the downstream edge is different from that at the center part of the cavity The pressure has its minimum value in the vortex core inside the cavity, and becomes very high at the downstream face of the cavity. The variation of the model coefficient predicted by the dynamic model is quite large between 0 and 0.3. The model coefficient increases in the stream-wise evolution of the shear layer and sharply decreases near the wall due to the wall effect.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.406-412
• /
• 2018

In this paper, we propose a narrow resonant waveguide probe that can improve the measurement sensitivity in near-field scanning microwave microscopy. The probe consists of a metal waveguide incorporating the following two sections: a straight section at the tip of the probe whose cross-section is a double-ridged rectangle, and whose height is much smaller than the waveguide width; and a standard waveguide section. The advantage of the narrow waveguide is the same as that of the quarter-wave transformer section i.e., it achieves impedance-matching between the sample under test (SUT) and the standard waveguide. The design procedure used for the probe is presented in detail and the performance of the designed resonant probe is evaluated theoretically by using an equivalent circuit. The calculated results are compared with those obtained using the finite element method (Ansoft HFSS), and consistency between the results is demonstrated. Furthermore, the performance of the fabricated resonant probe is evaluated experimentally. At X-band frequencies, we have measured the one-dimensional scanning reflection coefficient of the SUT using the probe. The sensitivity of the proposed resonant probe is improved by more than two times as compared to a conventional waveguide cavity type probe.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.343-344
• /
• 2008

A measurement method of the dielectric constant of materials whose standard sample is not prepared easily is proposed. The unprepared sample of the material is placed in a cavity, and the resonant frequency is measured. A commercial software simulates the same sample and the cavity leading to find the correct dielectric constant. The measured samples include a ceramic, a forced glass, and a powdered enamel.

• Proceedings of the Optical Society of Korea Conference
• /
• 2001.02a
• /
• pp.252-253
• /
• 2001

The purpose of this work is to investigate the dynamics of an atomic wave packet whose center-of-mass motion is quantized in a resonant standing wave cavity field. The mechanical aspect of the matter-field interaction has been extensively studied In the theme of atomic beam deflection, diffraction, or reflection by a standing-wave field. The effect caused in the behavior of spontaneous emission by the atomic center-of-mass motion, classical and quantized, in a standing wave cavity mode has been studied, and recently the one-atom laser with quantized atomic center-of-mass motion has been investigated. (omitted)

• Journal of the Korean Society of Propulsion Engineers
• /
• v.7 no.1
• /
• pp.40-48
• /
• 2003

Large eddy simulation is used to investigate the compressible flow over a open cavity, The sub-grid scale stresses are modeled using the dynamic model. The compressible Navier-Stokes equations are solved with the sixth order accurate compact finite difference scheme in the space and the 4th order Runge-Kutta scheme in the time. The results show a typical flow pattern of the shear layer mode of oscillation over the cavity. The votical disturbances, the roll-up of vorticity, and impingement and scattering of vorticity at the downstream cavity edge can be seen in the shear layer. Predicted acoustic resonant frequency is in good agreement with that of the empirical formula. The mean flow streamlines are nearly horizontal along the mouth of the cavity. The pressure has its minimum value in the vortex core inside the cavity.

• Journal of the Microelectronics and Packaging Society
• /
• v.16 no.4
• /
• pp.5-8
• /
• 2009

In this paper, a high-quality low-temperature co-fired ceramic (LTCC) solenoid inductor using a solder ball and an air cavity on a silicon wafer for three-dimensional (3-D) system-in-package (SiP) is proposed. The LTCC multi-layer solenoid inductor is attached using Ag paste and solder ball on a silicon wafer with the air cavity structure. The air cavity is formed on a silicon wafer through an anisotropic wet-etching technology and is able to isolate the LTCC dielectric loss which is equivalent to a low k material effect. The electrical coupling between the metal layer and the LTCC dielectric layer is decreased by adopting the air cavity. The LTCC solenoid inductor using the solder ball and the air cavity on silicon wafer has an improved Q factor and self-resonant frequency (SRF) by reducing the LTCC dielectric resistance and parasitic capacitance. Also, 3-D device stacking technologies provide an effective path to the miniaturization of electronic systems.

• Journal of electromagnetic engineering and science
• /
• v.5 no.3
• /
• pp.105-111
• /
• 2005

This paper presents the basic characteristics of a cutoff cavity-backed aperture antenna with a feed post and a parasitic post inserted parallel to the aperture. It is shown that this type of antenna forcibly resonates the cutoff cavity by adding a single external reactance to the parasitic post. The Galerkin's method of moments is used to analyze integral equations for the unknown electric current on each post and the aperture electric field on the aperture. The value of an external reactance for forced resonance is analytically obtained by deriving a determining equation. Also the current distribution on each post, aperture electric field distributions, and the radiation patterns are discussed. The theoretical analysis is verified by the measured return loss and radiation patterns.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.101-104
• /
• 2000

In this paper. the electric field intensity has been theoretically evaluated by the method of moments in a cavity by a external source. The numerical results show a good agreement with the results of other papers. It is found that the electromagnetic penetration through aperture in the cavity shows peak values at some frequencies dependent largely on the structure of the cavity and aperture.

• Journal of electromagnetic engineering and science
• /
• v.1 no.1
• /
• pp.37-42
• /
• 2001

This paper presents the basic characteristics of a cutoff cavity-hacked slot antenna, for the application of spacetenna, with a feed post and a parasitic post inserted parallel to the slot. This type of antenna might effectively excite the slot and forcibly resonate the cavity by adding external reactance to the parasitic post. The Galerkin\`s method of moments is used to analyze integral equations for the unknown electric current on each post and electric field in the slot. The value of external reactance for forced resonance is discussed by deriving a determining equation, the current distribution on each post and the radiation patterns are considered. The analysis is in excellent agreement with the experiment for the radiation patterns.