• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 Techno-Fair 및 추계학술대회 논문집 전기물성,응용부문
• /
• pp.154-155
• /
• 2007

This paper describes frequency response of two-mass system for gyroscope applications. The two-mass system of the proposed device is adapted to the sensing part of the gyroscope in this research. Two-mass system has two resonant peaks and wide flat region between two resonant peaks. The resonant frequency of driving part is in this flat region. Therefore, frequency tuning is not necessary for mode matching. In the proposed device, resonant frequency is designed as 7183 Hz in driving part. Mass ratio of two masses in sensing part is 0.1 and device size is 6 mm $\times$ 6 mm. The device is fabricated by SiOG process. The fabricated spring width is increased from $4{\mu}m$ to $4.5{\sim}4.7{\mu}m$, and the measured resonant frequency is 8392 Hz in driving mode. We operated the sensing part using parallel plate of proof mass to verify the sensing part. It is confirmed the device has a wide fiat region in frequency response curve and the resonant frequency of the driving part is in the wide flat region of sensing mode.

• 한국전기전자재료학회논문지
• /
• 제15권4호
• /
• pp.338-343
• /
• 2002

In this study, $Pb_{0.88}(La_{\alpha}Nd_{1-\alpha})_{0.08}(Mn_{1/3}Sb_{2/3})_{0.02}Ti_{0.98}O_3$ system ceramics with La molar ratio $\alpha$ variation were manufactured for 24 MHz class resonator application. Electromechanical coupling factor, mechanical quality factor and dynamic range of $3^{rd}$ overtone thickness vibration mode were measured as the variations of La and Nd molar ratio. Mechanical quality factor and dynamic range at $\alpha$ = 0.6 composition ceramics showed the highest value of 2691 and 52.37 dB, respectively. The temperature coefficient of resonant frequency measured from $-20^{\circ} to 80^{\circ}$ showed an excellent value of $5ppm/^{\circ}C$ at $\alpha$=1 composition ceramics.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1998년도 가을 학술발표회 논문집
• /
• pp.461-468
• /
• 1998

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2018년도 춘계학술대회
• /
• pp.55-56
• /
• 2018

본 논문에서는 H-모양 공진 개구를 이용한 평면 기판의 유전율 특성 분석 방법을 제안하였다. 이를 위해 마이크로스트립 전송선로의 접지면에 H-모양 공진 개구를 추가하여 대역 저지 필터를 생성하였다. 마이크로스트립 전송선로의 접지면 뒤에 2 mm 두께의 평면 기판을 놓고 기판의 유전율 변화에 따른 공진주파수의 변화를 조사하였다. 기존의 상보 분할 링 공진기 구조를 사용하였을 때와 비교하여 기준 공진주파수에 대한 주파수의 변화 비가 커짐을 알 수 있었다.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제4C권5호
• /
• pp.193-200
• /
• 2004

In this study, we propose a small high voltage power supply, which uses a half-bridge ZCS resonant and Cockroft-Walton circuit as its ESP (Electrostatic Precipitator). This power supply transfers energy from the ZCS resonant inverter to the step-up transformer. The transformer secondary is then applied to the Cockroft-Walton circuit for generating high voltage as a discharging source of electrodes. It is highly efficient because its amount of switching losses are reduced by virtue of the current resonant half-bridge inverter, and also due to the small size, low parasitic capacitance in the transformer stage owing to the low number of winding turns of the step up transformer secondary combined with the Cockroft-Walton circuit. Using this power supply, experiments have been carried out as a function of the switching frequency and duty ratio in order to investigate the smoke removal characteristics. From these results, the best operational condition is obtained at the switching frequency of 9 kHz and the duty ratio of 50% in this ESP.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2008년도 하계학술대회 논문집
• /
• pp.508-510
• /
• 2008

In designing a LLC resonant converter, the ratio of magnetizing inductance ($L_M$) to resonant inductance ($L_R$), the inductor ratio (K) is usually considered. In high power density adapter, both adapter size and efficiency are important factors. Considering the size of adapter, high K design can be more attractive. But, wide frequency variation of high K design results in design difficulty of magnetic elements and decrease in efficiency. To solve these drawbacks, an adaptive link voltage variation (ALVV) control is proposed. With the proposed control method, the LLC resonant converter can be operated at the resonant frequency despite the output voltage variation. The control strategy and schematics are presented, and verified experimentally.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.877-880
• /
• 2000

The length extensional vibration mode of a piezoelectric ceramic substrate is used in fabricating the ultra-small size resonators and filters. In general, the three side ratios of the substrate effect the resonant characteristics of the resonator using its length extensional vibration. In this paper, their relationships are studied. We know that changing the ratio of its length to its width makes possible to change the resonant frequency of the width vibration without degrading the length extensional vibration.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권2호
• /
• pp.132-139
• /
• 2000

This paper reports a novel micromachining process based on UV-LIGA process and (110) silicon anisotropic etching for fabrication of a high-aspect-ratio comb actuator. The comb electrodes are fabricated by (110) SILICON comb structure considering the etch-rate-ratio between (110) and (111) planes and lateral etch rate of a beam-type structure. The fabricated structure was$ 400\mum \; thick\; and\; 18\mum$ wide comb electrodes separated by $7\mim$ so that the height-gap ratio was about 57. Also considering resonant frequency of the comb actuator and the frequency-matching between sensing and driving mode for gyroscope application, we designed the number, width, height and length of the spring structures. Electroplated gold springs on both sides of the seismic mass were $15\mum\; wide,\; 14\mum\; thick\; and \; 500\mum$ long. The fabricated comb actuator had resonant frequency ay 1430Hz, which was calculated to be 1441Hz. The proposed fabrication process can be applicable to the fabrication of a high-aspect-ratio comb actuator for a large displacement actuator and precision sensors. Moreover, this combined process enables to fabricate a more complex structure which cannot be fabricate only by surface or bulk micromachining.

• 소음진동
• /
• 제4권2호
• /
• pp.209-219
• /
• 1994

Classical method calculates the resonance frequency of Helmholtz resonator by postulating that there is a moving mass in neck and a stiffness which expresses the compressibility of cavity. This has been widely accepted as reasonable to determine the resonant frequency, provided that the wave length of interest is longer that any length scale of resonater. Nevertheless, it has been often recognized that this classical method sometimes does not well predict the resonant frequency. This paper decribes the way in which the dynamics of resonator very often does care about the detail geometries of resonator; location of the neck, diameter ratio of the neck to that of cavitty, length of resonator compared with that of neck, etc. This rather unexpected observations have been proved theoretically; 3 dimensional analysis of acoustic wave equation, as well as experimentally by comparing the resonant frequencies, transmission loss, and insertion loss of resonator.

• 한국광학회:학술대회논문집
• /
• 한국광학회 1989년도 제4회 파동 및 레이저 학술발표회 4th Conference on Waves and lasers 논문집 - 한국광학회
• /
• pp.152-156
• /
• 1989

Parameters of a microstrip patch antenna such as the resonant frequency, radiation conductance, and the bandwidth are calculated. The rectangular microstrip patch antenna fed by a microstrip transmission line is fabricated and its resonant frequency, radiation pattern, and input voltage standing wave ratio are measured. The measured resonant frequency for 13.0mm$\times$9.7mm copper clad woven PTFE/glass laminate plate is 9.06Ghz, where the calculative is 9.00Ghz. And the measured vswr shows that the bandwidth of the antenna is 225MHz for vswr less then 2.0 which the calculated quality factor of the patch gives the bandwidth OF 280ghZ. The measured radiation pattern for 5 element as well as 4 element patch array shows less then 4dB deviation in the first side lobes from the designed values for both E and H plane pattern. This diviation is believed to be the power division errors of the power divider.