• 한국군사과학기술학회지
• /
• 제21권4호
• /
• pp.413-421
• /
• 2018

The pyroshocks can cause failure of electronics devices and structures. Metal-metal impact methods are utilized to simulate mechanical pyroshock, and to adjust the knee frquency of the SRS(Shock Response Spectrum) through resonant structures. In this paper, the major parameters of pyroshock simulation device which affect the SRS were examined. Through the Hertzian contact law and the modal characteristics of the resonant bar, it was found that the SRS is affected by the length and mass of a bar and various impact conditions such as velocity and mass of impactor. The characteristics due to the geometric parameters of a resonant bar was analyzed by performing FEA and also the resonant bar was designed and fabricated. Through the pyroshock simulation test, the characteristics of SRS due to the variation of impact parameters were examined.

• 비파괴검사학회지
• /
• 제32권1호
• /
• pp.1-6
• /
• 2012

본 연구에서는 광대역(100 kHz - 1 MHz) 탐촉자를 사용하여 자동차용 CNG연료탱크의 파열시험시 발생하는 음향방출신호의 분석을 통해 압력용기의 손상정도를 평가하였다. 압력이 420 bar까지 올라가기 전의 각 단계에서는 Kaiser 효과가 나타나고 creep 효과가 거의 나타나지 않으나, 420 bar 이상 상승시 creep 효과가 현저히 나타남으로써 용기가 손상을 입었다는 것을 알 수 있었으며, 480 bar 압력 상승 단계에서는 Kaiser 효과가 없어졌다. 540 bar의 압력 단계에서 공진형 탐촉자의 경우에서는 480 bar의 압력단계에 비하여 energy나 count 같은 activity가 감소하였으나 광대역 탐촉자의 경우 계속적으로 증가하였다. 또한 rise time이나 주파수 분석을 통해서 복합재료 압력용기의 손상 메카니즘을 관찰하기 위해서는 일반적으로 금속압력용기에서 많이 사용되는 공진형 탐촉자(150 kHz)보다 광대역 탐촉자가 효과적임을 알 수 있었다.

• 천문학회지
• /
• 제29권spc1호
• /
• pp.273-276
• /
• 1996

The world wide efforts for detecting gravitational waves, the detectors in vogue and the expected astrophysical sources of gravitational waves will be discussed. Ground based detectors especially, the resonant bar detectors and laser interferometers will be described with a brief mention of the space based detector (the LISA project). Astrophysical sources of gravitational waves such as coalescing binaries, supernovae, pulsars/ rotating neutron stars, stochastic background will be discussed in the context of detection.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.347-351
• /
• 1997

A micromachined piezoelectic cantilever transducer,which works both as a microphone and as a microspeaker,has been fabricated and tested. The 2000*2000*3.mu.m .sap2. cantilever has oxide(ZnO)piezoelectric thin film on a supporting layer of low-pressure chemical-vapor-deposited(LPCVD)low-stress siliconnitride. A highlight of the fabrication process which may also be relevant for other micromachined stuctures is the technique for producing a flat,multilayer cantilever. The measured microphone sensitivity is fairly constant at 2 mV/.mu.bar in the low frequency range and rise to 20 mV/.mu.bar at the lowest resonant frequency of 890 Hz. The 2 mV/.mu.bar sensitivity is the highest report to data for a microphone with a micromachined diaphragm. When measured into a 2 cm/sap3 coupler with 4V (zero-park)drive,the microspeaker output sound pressure level(SPL) is 75 dB at 890 Hz. It increases to approximately 100dB SPL at 4.8kHz with 6V(zero-park)drive. The measured microphone frequency response agrees well with the results of an ABAQUS simulation.

• 한국정밀공학회지
• /
• 제25권11호
• /
• pp.90-94
• /
• 2008

Recently, a great deal of research is focused on the printed electronics. One of their mainly concerned products is printed RFID tag. RFID technology has attracted researchers and enterprises as a promising method for automatic identification, and they are expected to replace conventional bar codes in inventory tracking and management. The key to successful RFID technology lies in developing low-cost RFID tags and the first step in applying printing technology to RFID systems is to replace antennas that are conventionally produced by etching copper or aluminum. However, due to the printing quality variations, errors, and lower conductivity, the performance of the printed RFID antennas is lower than that of antennas manufactured by conventional etching methods. In this paper, the effect of variations in the printing conditions on the antenna performance is investigated. Three levels for each condition parameter is assumed and effect on the resonant frequency are examined experimentally based on orthogonal array. The most serious factor that affects the resonant frequency of the antenna is the non-uniformity of the edge and the resonant frequency is found to be lower as the non-uniformity increases.

• 수산해양기술연구
• /
• 제35권3호
• /
• pp.312-322
• /
• 1999

A ultrasonic transduce with a single acoustic matching layer has been designed as an attempt to increase the bandwidth of underwater transducer. The wideband resonance condition was accomplished by attaching a single matching layer on the front face of a ceramic resonator composed of a piezoelectric bar, a taper part and a head part. A modified Mason's model was used for the performance analysis and the design of transducers, and the constructed transducers were tested experimentally and numerically by changing the impedance and thickness of the matching layer in the water tank.The obtained results are summarized as follows:1. Measured resonant and antiresonant frequencies of the piezoelectric transducer with no matching layer in air were 24.7 kHz and 25.6 kHz, respectively. 2. Two resonant frequencies of the piezoelectric transducer with a single matching layer were 21.7 kHx and 26.9 kHz, respectively, in air and 21.4 kHz and 22.7 kHz, respectively, with a water load.3. Two distinct resonance peaks in the transmitting voltage response(TVR) of the developed transducer were observed at 22.0 kHz and 25.8 kHz, respectively, with center frequency of 24.0 kHz. The values of TVR at these frequencies were 130.1 dB re $1 \muPa$/V at 22.0 kHz and 128.5 dB re $1 \muPa$/V at 25.8 kHz, respectively.Reasonable agreement between the experimental results and the numerical values was achieved.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.168-171
• /
• 2005

In this paper, disk-type ultrasonic motor using a combination of radial and bending vibration modes is newly designed and fabricated. The characteristics of the test motor are also measured. By means of traveling elastic wave induced at the surface of circumference of the elastic disk, a steel bar in contact with the surface of circumferenceof elastic disk bonded onto the piezoelectric ceramic disks is driven in both directions by changing the sine and cosine voltage inputs. The stator of the motor is composed of two sheets of piezoelectric ceramic disk to bond onto both surfaces of a elastic disk, respectively. As the results, the diameter of elastic body is increased, the resonant frequency is decreased. The resonant frequency of the stator is about 92 kHz, which is composed with piezoelectric ceramic disks of 28 mm in diameter and 2 mm in thickness, and an elastic body of 32 mm in diameter and 2 mm in thickness. A driving voltage of 20 Vpp produces 200 rpm with a torque of 1Nm and an efficiency of about 10 %.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.232-233
• /
• 2005

In this paper, disk-type ultrasonic motor using a combination of radial and bending vibration modes is newly designed and fabricated. The characteristics of the test motor are also measured. By means of travelingelastic wave induced at the surface of circumference of the elastic disk, a steel bar in contact with the surface of circumference of elastic disk bonded onto the piezoelectric ceramic disks is driven inboth directions by changing the sine and cosine voltage inputs. The stator of the motor is composed of two sheets of piezoelectric ceramic disk to bond onto both surfaces of a elastic disk, respectively. As the results, the diameter of elastic body is increased, the resonant frequency is decreased. The resonant frequency of the stator is about 92 kHz, which is composed with piezoelectric ceramic disks of 28 mm in diameter and 2 mm in thickness, and an elastic body of 32 mm in diameter and 2 mm in thickness. A driving voltage of 20 Vpp produces 200 rpm with a torque of 1Nm and an efficiency of about 10 %.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 C
• /
• pp.1718-1720
• /
• 2004

This paper is focused on the improvement of reflection angle of an optical scanner by changing a shape of a torsion bar attached with an optical scanner reflector(mirror). In order to improve the light efficiency of the optical scanner by virtue of the magnetic effect, which tiny magnets are attached under both ends of the optical scanner reflector. and hence the optical scanner reflector was operated in relatively lower driving voltage. By changing the torsion bar's shape I type into S type, we've got the lower resonant frequency(32.5Hz) of an optical scanner than that of conventional one(50Hz). According to these results. The reflection angle of an optical scanner with magnets was much larger in the range of about 14.8$^{circ}$ without a magnet. By making use of a magnetic actuator instead of a conventional electrostatic actuator, the optical scanner was less influenced from outdoor dust or moisture.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제30회 춘계학술대회논문집
• /
• pp.121-124
• /
• 2008

본 논문에서 연료 과농 가스발생기의 동적 연소 특성을 수록하였다. 연소실과 추진제 매니폴드 내에서 발생하는 압력 섭동을 계측하여 데이터 분석을 실시하였다. 단독 연소 시험에서는 연소압에 관계없이 연소가 안정적으로 이루어졌으나 터빈 매니폴드 장착의 경우, 산소 임계 압력에 해당하는 50 bar이하의 저압 조건에서 저주파 연소 불안정이 발생하는 것을 확인하였다. 이는 연소실 특성 길이 증가에 의한 축방향 연소 불안정으로 여겨지며, 연소압 증가에 따라 압력 섭동이 증가함을 확인하였다.