• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.4
• /
• pp.413-421
• /
• 2018

The pyroshocks can cause failure of electronics devices and structures. Metal-metal impact methods are utilized to simulate mechanical pyroshock, and to adjust the knee frquency of the SRS(Shock Response Spectrum) through resonant structures. In this paper, the major parameters of pyroshock simulation device which affect the SRS were examined. Through the Hertzian contact law and the modal characteristics of the resonant bar, it was found that the SRS is affected by the length and mass of a bar and various impact conditions such as velocity and mass of impactor. The characteristics due to the geometric parameters of a resonant bar was analyzed by performing FEA and also the resonant bar was designed and fabricated. Through the pyroshock simulation test, the characteristics of SRS due to the variation of impact parameters were examined.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.1
• /
• pp.1-6
• /
• 2012

This study is damage evaluation for CNG fuel tank during the burst test through the analysis of acoustic emission signals. Kaiser effect until the pressure 420 bar appears, but More than 420 bar by the creep effect appears significantly damaged vessels, and 480 bar pressure, the Kaiser effect of the rising phase was missing. Resonant transducer at 540 bar than 480 bar decreased activity such as energy and count Continually, but increased wideband transducer. In addition, through the rise time or frequency analysis of composite pressure vessels in order to observe the damage mechanisms wideband transducer is more effective than resonant transducer.

• Journal of The Korean Astronomical Society
• /
• v.29 no.spc1
• /
• pp.273-276
• /
• 1996

The world wide efforts for detecting gravitational waves, the detectors in vogue and the expected astrophysical sources of gravitational waves will be discussed. Ground based detectors especially, the resonant bar detectors and laser interferometers will be described with a brief mention of the space based detector (the LISA project). Astrophysical sources of gravitational waves such as coalescing binaries, supernovae, pulsars/ rotating neutron stars, stochastic background will be discussed in the context of detection.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.347-351
• /
• 1997

A micromachined piezoelectic cantilever transducer,which works both as a microphone and as a microspeaker,has been fabricated and tested. The 2000*2000*3.mu.m .sap2. cantilever has oxide(ZnO)piezoelectric thin film on a supporting layer of low-pressure chemical-vapor-deposited(LPCVD)low-stress siliconnitride. A highlight of the fabrication process which may also be relevant for other micromachined stuctures is the technique for producing a flat,multilayer cantilever. The measured microphone sensitivity is fairly constant at 2 mV/.mu.bar in the low frequency range and rise to 20 mV/.mu.bar at the lowest resonant frequency of 890 Hz. The 2 mV/.mu.bar sensitivity is the highest report to data for a microphone with a micromachined diaphragm. When measured into a 2 cm/sap3 coupler with 4V (zero-park)drive,the microspeaker output sound pressure level(SPL) is 75 dB at 890 Hz. It increases to approximately 100dB SPL at 4.8kHz with 6V(zero-park)drive. The measured microphone frequency response agrees well with the results of an ABAQUS simulation.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.11
• /
• pp.90-94
• /
• 2008

Recently, a great deal of research is focused on the printed electronics. One of their mainly concerned products is printed RFID tag. RFID technology has attracted researchers and enterprises as a promising method for automatic identification, and they are expected to replace conventional bar codes in inventory tracking and management. The key to successful RFID technology lies in developing low-cost RFID tags and the first step in applying printing technology to RFID systems is to replace antennas that are conventionally produced by etching copper or aluminum. However, due to the printing quality variations, errors, and lower conductivity, the performance of the printed RFID antennas is lower than that of antennas manufactured by conventional etching methods. In this paper, the effect of variations in the printing conditions on the antenna performance is investigated. Three levels for each condition parameter is assumed and effect on the resonant frequency are examined experimentally based on orthogonal array. The most serious factor that affects the resonant frequency of the antenna is the non-uniformity of the edge and the resonant frequency is found to be lower as the non-uniformity increases.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.35 no.3
• /
• pp.312-322
• /
• 1999

A ultrasonic transduce with a single acoustic matching layer has been designed as an attempt to increase the bandwidth of underwater transducer. The wideband resonance condition was accomplished by attaching a single matching layer on the front face of a ceramic resonator composed of a piezoelectric bar, a taper part and a head part. A modified Mason's model was used for the performance analysis and the design of transducers, and the constructed transducers were tested experimentally and numerically by changing the impedance and thickness of the matching layer in the water tank.The obtained results are summarized as follows:1. Measured resonant and antiresonant frequencies of the piezoelectric transducer with no matching layer in air were 24.7 kHz and 25.6 kHz, respectively. 2. Two resonant frequencies of the piezoelectric transducer with a single matching layer were 21.7 kHx and 26.9 kHz, respectively, in air and 21.4 kHz and 22.7 kHz, respectively, with a water load.3. Two distinct resonance peaks in the transmitting voltage response(TVR) of the developed transducer were observed at 22.0 kHz and 25.8 kHz, respectively, with center frequency of 24.0 kHz. The values of TVR at these frequencies were 130.1 dB re $1 \muPa$/V at 22.0 kHz and 128.5 dB re $1 \muPa$/V at 25.8 kHz, respectively.Reasonable agreement between the experimental results and the numerical values was achieved.

• Proceedings of the KIEE Conference
• /
• 2005.11a
• /
• pp.168-171
• /
• 2005

In this paper, disk-type ultrasonic motor using a combination of radial and bending vibration modes is newly designed and fabricated. The characteristics of the test motor are also measured. By means of traveling elastic wave induced at the surface of circumference of the elastic disk, a steel bar in contact with the surface of circumferenceof elastic disk bonded onto the piezoelectric ceramic disks is driven in both directions by changing the sine and cosine voltage inputs. The stator of the motor is composed of two sheets of piezoelectric ceramic disk to bond onto both surfaces of a elastic disk, respectively. As the results, the diameter of elastic body is increased, the resonant frequency is decreased. The resonant frequency of the stator is about 92 kHz, which is composed with piezoelectric ceramic disks of 28 mm in diameter and 2 mm in thickness, and an elastic body of 32 mm in diameter and 2 mm in thickness. A driving voltage of 20 Vpp produces 200 rpm with a torque of 1Nm and an efficiency of about 10 %.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.232-233
• /
• 2005

In this paper, disk-type ultrasonic motor using a combination of radial and bending vibration modes is newly designed and fabricated. The characteristics of the test motor are also measured. By means of travelingelastic wave induced at the surface of circumference of the elastic disk, a steel bar in contact with the surface of circumference of elastic disk bonded onto the piezoelectric ceramic disks is driven inboth directions by changing the sine and cosine voltage inputs. The stator of the motor is composed of two sheets of piezoelectric ceramic disk to bond onto both surfaces of a elastic disk, respectively. As the results, the diameter of elastic body is increased, the resonant frequency is decreased. The resonant frequency of the stator is about 92 kHz, which is composed with piezoelectric ceramic disks of 28 mm in diameter and 2 mm in thickness, and an elastic body of 32 mm in diameter and 2 mm in thickness. A driving voltage of 20 Vpp produces 200 rpm with a torque of 1Nm and an efficiency of about 10 %.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1718-1720
• /
• 2004

This paper is focused on the improvement of reflection angle of an optical scanner by changing a shape of a torsion bar attached with an optical scanner reflector(mirror). In order to improve the light efficiency of the optical scanner by virtue of the magnetic effect, which tiny magnets are attached under both ends of the optical scanner reflector. and hence the optical scanner reflector was operated in relatively lower driving voltage. By changing the torsion bar's shape I type into S type, we've got the lower resonant frequency(32.5Hz) of an optical scanner than that of conventional one(50Hz). According to these results. The reflection angle of an optical scanner with magnets was much larger in the range of about 14.8$^{circ}$ without a magnet. By making use of a magnetic actuator instead of a conventional electrostatic actuator, the optical scanner was less influenced from outdoor dust or moisture.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.121-124
• /
• 2008

This paper presents experimental results of dynamic characteristics of fuel-rich gas generators. Pressure fluctuation measurements in the chamber and manifolds have been analyzed. Gas-generator-alone tests revealed stable combustion regardless of a chamber pressure but low-frequency combustion instabilities occurred for cases of turbine-manifold tests at chamber pressure conditions below 50 bar. The instabilities are considered as an axial resonant mode and acoustic intensity increases along with a chamber pressure.