• Steel and Composite Structures
• /
• v.38 no.5
• /
• pp.563-582
• /
• 2021

The present study experimentally and analytically investigated the push-out behaviour of H-shaped steel section embedded in ultrahigh-performance fibre-reinforced concrete (UHPFRC). The effect of significant parameters such as the concrete types, fibre content, embedded steel length, transverse reinforcement ratio and concrete cover on the bond stress, development of bond stress along the embedded length and failure mechanism has been reported. The test results show that the bond slip behaviour of steel-UHPFRC is different from the bond slip behaviour of steel-normal concrete and steel-high strength concrete. The bond-slip curves of steel-normal concrete and steel-high strength concrete exhibit brittle behaviour, and the bond strength decreases rapidly after reaching the peak load, with a residual bond strength of approximately one-half of the peak bond strength. The bond-slip curves of steel-UHPFRC show an obvious ductility, which exhibits a unique displacement pseudoplastic effect. The residual bond strength can still reach from 80% to 90% of the peak bond strength. Compared to steel-normal concrete, the transverse confinement of stirrups has a limited effect on the bond strength in the steel-UHPFRC substrate, but a higher stirrup ratio can improve cracking resistance. The experimental campaign quantifies the local bond stress development and finds that the strain distribution in steel follows an exponential rule along the steel embedded length. Based on the theory of mean bond and local bond stress, the present study proposes empirical approaches to predict the ultimate and residual bond resistance with satisfactory precision. The research findings serve to explain the interface bond mechanism between UHPFRC and steel, which is significant for the design of steel-UHPFRC composite structures and verify the feasibility of eliminating longitudinal rebars and stirrups by using UHPFRC in composite columns.

• The Korea Journal of Herbology
• /
• v.35 no.3
• /
• pp.47-54
• /
• 2020

Objective : Infectious diseases are a growing problem worldwide by Methicillin-resistant Staphylococcus aureus (MRSA). Daehwangmokdan-tang is one of the oriental medicine prescriptions contained in Principles and Practice of Eastern Medicine. This study investigated the antibacterial activity of EtOH 70% extracts of Daehwangmokdan-tang (DMT) which prescription is composed of oriental medicine against MRSA. Methods : The antimicrobial activity and active concentration of MRSA were verified by measuring the minimum inhibitory concentration (MIC) of DMT. In addition, the effects of the disease were checked by treating the existing antibiotics and large ethanol extract in parallel, and the extent of growth suppression was checked over time. In addition, cell membrane permeability experiment confirmed the effect of large DMT on the immunity mechanism of MRSA. Results : TThe minimum inhibitory concentration of DMT against MRSA is 500 ~ 2000 ㎍/㎖ by broth dilution method. In the checkerboard method, the combinations of DMT with antibiotics has partial synergistic effect or synergy effect and DMT markedly reduced the MICs of the antibiotics oxacillin (OX), gentamicin (GEN) against MRSA. In the inhibition of resistance mechanism of DMT against MRSA, the expression of resistance gene and protein about β-lactam antibiotic was reduced. Also, we observed the effect of DMT about cell membrane permeability against MRSA, and confirmed that DMT suppressed growth of strains by increasing cell membrane permeability and energy metabolism. Conclusion : Basis on the result, we speculate that DMT may be useful for the treatment of MRSA infections when used in combination with β-lactam antibiotic.

• Journal of Microbiology and Biotechnology
• /
• v.19 no.10
• /
• pp.1250-1258
• /
• 2009

Bacillus spp., as a type of plant growth-promoting rhizobacteria (PGPR), were studied with regards promoting plant growth and inducing plant systemic resistance. The results of greenhouse experiments with tobacco plants demonstrated that treatment with the Bacillus spp. significantly enhanced the plant height and fresh weight, while clearly lowering the disease severity rating of the tobacco mosaic virus (TMV) at 28 days post-inoculation (dpi). The TMV accumulation in the young non-inoculated leaves was remarkably lower for all the plants treated with the Bacillus spp. An RT-PCR analysis of the signaling regulatory genes Coil and NPR1, and defense genes PR-1a and PR-1b, in the tobacco treated with the Bacillus spp. revealed an association with enhancing the systemic resistance of tobacco to TMV. A further analysis of two expansin genes that regulate plant cell growth, NtEXP2 and NtEXP6, also verified a concomitant growth promotion in the roots and leaves of the tobacco responding to the Bacillus spp.

• Journal of Soil and Groundwater Environment
• /
• v.6 no.1
• /
• pp.53-62
• /
• 2001

Effects of surface defect on thermal stability and stress crack resistance of high density polyethylene geomembranes in environmental conditions were examined by comparing the mechanical properties, chemical resistance and failure times of geomembranes between defective cases under different temperatures. Artificial surface defects were added to the surface of geomembranes by scratch apparatus designed specially. The number of surface defects was increased with the smaller size of scratch induced particles, and the more scratch addition numbers at the shear rate of scratch induced mechanism, 100mm/min. The tensile strength were decreased but the tensile strain was increased with the above conditions. In chemical resistance of defective geomembranes, the tensile strength were decreased but the tensile strain was increased with the longer immersion period and the higher temperature under the same scratch induced conditions. Finally, failure times of defective geomembranes by ESCR test were shifted to the shorter time ranges by increasing temperatures.

• Mycobiology
• /
• v.33 no.3
• /
• pp.131-136
• /
• 2005

Infection structures were observed at the penetration sites on the leaves of cucumber plants inoculated with Colletotrichum orbiculare using a fluorescence microscope. The cucumber plants were previously drenched with suspension of bacterial strains Pseudomonas putida or Micrococcus luteus. The plants pre-inoculated with both bacterial strains were resistant against anthracnose after inoculation with C. orbiculare. To investigate the resistance mechanism by both bacterial strains, the surface of infected leaves was observed at the different time after challenge inoculation. At 3 days after inoculation there were no differences in the germination and appressorium formation of conidia of C. orbiculare as well as in the callose formation of the plants between both bacteria pre-inoculated and non-treated. At 5 days, the germination and appressorium formation of the fungal conidia were, however, significantly decreased on the leaves of plants pre-inoculated with M. luteus at the concentration with $1.0{\times}10^7\;cfu/ml$. Furthermore, callose formation of plants cells at the penetration sites was apparently increased. In contrast, there were no defense reactions of the plants at the concentration with $1.0{\times}10^6\;cfu/ml$ of M. luteus. Similarly, inoculation P. putida caused no plant resistance at the low concentration, whereas increase of callose formation was observed at the higher concentration. The results of this study suggest that the resistant mechanisms might be differently expressed by the concentration of pre-treatment with bacterial suspension.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.9
• /
• pp.2374-2385
• /
• 1994

SiCw/Al composite material is especially attractive because of their superior specific strength, specific stiffness, corrosion fatigue resistance, creep resistance, and wear resistance compared with the corresponding wrought Al alloy. In this study, Fatigue crack growth behavior and fatigue crack path morphology(FCPM) of SiC whisker reinforced Al 6061 alloy with 25% SiC volume fraction and Al 6061 allay were performed. Result of the fatigue crack growth test sgiwed that fatigue crack growth rate of SiCw/Al 6061 composite was slower than that of Al 6061 matrix therefore it was confirmed that Sic whisker have a excellent fatigue resistance. And Al 6061 matrix had only FCPM perpendicular to loading direction. On the other hand SiCw/Al 6061 composite had three types in fatigue crack path morphology. First type is that both sides FCPM of artificial notch are perpendicular to loading direction. Second type is that a FCPM in artifical notch has slant angle to loading direction and the other side FCPM is perpendicular to loading direction. Third type is that both sides FCPM of notch have slant angle to loading direction. It was considered that this kinds of phenomena were due to non-uniform distribution of SiC whisker and confirmed by SEM observation for fracture mechanism study.

• Asian Pacific Journal of Cancer Prevention
• /
• v.14 no.11
• /
• pp.6321-6326
• /
• 2013

Introduction: Lung cancer is extremely harmful to human health and has one of the highest worldwide incidences of all malignant tumors. Approximately 80% of lung cancers are classified as non-small cell lung cancers (NSCLCs). Cisplatin-based multidrug chemotherapy regimen is standard for such lesions, but drug resistance is an increasing problem. F-box/WD repeat-containing protein 7 (FBW7) is a member of the F-box protein family that regulates cell cycle progression, and cell growth and differentiation. FBW7 also functions as a tumor suppressor. Methods: We used cell viability assays, Western blotting, and immunofluorescence combined with siRNA interference or plasmid transfection to investigate the underlying mechanism of cisplatin resistance in NSCLC cells. Results: We found that FBW7 upregulation significantly increased cisplatin chemosensitivity and that cells expressing low levels of FBW7, such as NCI-H1299 cells, have a mesenchymal phenotype. Furthermore, siRNA-mediated silencing or plasmid-mediated upregulation of FBW7 resulted in altered epithelial-mesenchymal transition (EMT) patterns in NSCLC cells. These data support a role for FBW7 in regulating the EMT in NSCLC cells. Conclusion: FBW7 is a potential drug target for combating drug resistance and regulating the EMT in NSCLC cells.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.30 no.1
• /
• pp.54-60
• /
• 2016

Amomum cadamomum Linne (ACL) has long been utilized against the inhibited qi movement related diseases such as dyspepsia, acute gastroenteritis, vomiting and diarrhea in Korean medicine. We speculated that ACL could improve the metabolic disorders such as obesity and type 2 diabetes through removing the phlegm-dampness and promoting the qi movement or stagnation. This study was designed to investigate effects and molecular mechanisms of ACL extract on the improvement of adipocyte dysfunction induced by TNF-α in 3T3-L1 adipocytes. Potential roles of ACL extract in the lipogenesis, inhibition of inflammatory cytokines and insulin resistance, were investigated in this study. Also, we examined the adipose genes and signaling molecules related to insulin resistance and glucose uptake to elucidate its mechanism. Our data demonstrated that TNF-α significantly incresed the release of lipid droplets and the production of MCP-1 and IL-6 from adipocytes. In gene expression, TNF-α reduced the expression of aP2, PPARγ, C/EBPα, GLUT4, and IRS-1 related to lipogenesis and insulin sesitivity, while TNF-α increased the expression of MCP-1 related to inflammation. In addition, TNF-α down-regulated the PPARγ and IRS-1 protein and up-regulated the IRS-1 Ser307 phosphorylation. These alterations induced by TNF-α were prevented by the treatment of ACL extract. Thus, our results indicate that ACL extract can be used to prevent from the TNF-α-induced adipocyte dysfunction through insulin and PPARγ pathways.

• Biomedical Science Letters
• /
• v.20 no.2
• /
• pp.85-95
• /
• 2014

Activation of the epidermal growth factor receptor (EGFR) and downstream signaling pathways have been implicated in causing resistance to EGFR-targeted therapy in solid tumors, including the head and neck tumors. To investigate the mechanism of antiproliferation to EGFR inhibition in oral cancer, we compared EGFR tyrosine kinase inhibitor (Gefitinib, Iressa, ZD1839) with respect to its inhibitory effects on three kinases situated downstream of EGFR: MAPK, Akt, and glycogen synthase kinase-$3{\beta}$ (GSK-$3{\beta}$). We have demonstrated that ZD1839 induces growth arrest and apotosis in oral cancer cell lines by independent of EGFR-mediated signaling. An exposure of oral cancer cells to ZD1839 resulted in a dose dependent up-regulation of the cyclin-dependent kinase inhibitor p21 and p27, down regulation of cyclin D1, inactivation of GSK-$3{\beta}$ and of active MAPK. In resistant cells, GSK-$3{\beta}$ is constitutively active and its activity is negatively regulated primarily through Ser 9 phosphorylation and further enhanced by Tyr216 phosphorylation. These results showed that the resistance to the antiproliferative effects of ZD1839, in vitro was associated with uncoupling between EGFR and MAPK inhibition, and that GSK-$3{\beta}$ activation and degradation of its target cyclin D1 were indicators of high cell sensitivity to ZD1839. In conclusion, our data show that the uncoupling of EGFR with mitogenic pathways can cause resistance to EGFR inhibition in oral cancer.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.1
• /
• pp.12-23
• /
• 1998

The Thermal Barrier Coating(TBC) has been used to improve the heat barrier and tribological properties of the aircraft engine and the automobile engine in high temperature. Especially, the high temperature tribological propertied of the cylinder haed and the piston crown of diesel engine was emphasized. Therefore, the purpose of this work was to evaluate the microstructure, tribological propeer in high tempearmal shock resistance and bonding strength of five layer functionally gradient TBC for the applications. The five layerwere composed with 100% ceramic insulating later, 75(ceramic):25 (metal) layer, 50:50 layer, 25:75 layer and 100% metal bonding layer to redude the thermal stress. the YSL and MSL poweders were the insulation ceramics powers. The NiCrAly, Inconel625 and SUS powders were the bonding and mixingg powders for plasma spray process. According to the result of high temperature wear test, the wera resistance of YSZ/NiCrAlY siytem was most out standing at 600 and $800^{\circ}C$. At $400^{\circ}C$, the wear resistance of YSZ/Inconel system was better than others. Wear volume at other temperature because of the low temperature degration of zirconia. The thermal shock mechanism of 5 later is the vertical crack gegration in insulating layer. this means that the initial cracks were generated in the top layer, and then developed into the composite layers during thermal shock test. Finally, these cracks werereached to the interface of coating and substrate and also, these vertioal cracks join with the horizontal cracks of the each layers. The bonding strength of YSZ/NiCrAlY and YSZ/Inconel 5 layer system is better than other 5layer systems. The theramal shock resistance of thermal barrier coating s with 5 layer system is better than that of 3 layers and 2 layers.