• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.325-330
• /
• 1999

The objectives of this study were to compare the development of compressive strength of epoxy resin mortars used as repairing materials with respect to maturity, and to propose a predictive model for strength development of epoxy resin mortar. A series of tests were carried out for the hardener contents of 30, 40 and 50 percentage of resin and compressive strength were measured at the of 6, 12, 24, 72, 120 and 168 hours respectively under temperature of 0, 10, 20 and 3$0^{\circ}C$. The datum temperature was estimated by measured strength, and the maturity is calculated with the estimated datum temperature. The compressive strength of epoxy resin mortar could be predicted by regression analysis from the maturity-compressive strength relationship.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.761-764
• /
• 2005

Epoxy resin, as no-hardening, applied for repair and finish materials is used to mix together with hardener. It is advantages that epoxy resin has reaction shrinkage less than other materials and has excellent in water proofing, thermal resistance. The other hands, because ratio of combination of epoxy resin and hardener is fixed, it is not possible to change according to field condition. This investigated suspended time by temperature and hardener ratio. As a results of study, it can select economical ratio of the epoxy resin and hardener according to site situation.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1992.04a
• /
• pp.35-40
• /
• 1992

Results of an experimental study on the manufacture, the workability and mechanical properties of steel fiber reinforced polyester resin composites utilizing industrial waste products are presented in this paper. The fly ash polyester resin composites using steel fiber, fly ash and calcium carbonic acid (CaCo3), unsaturated polyester resin, styrene monomer, cobalt octate and methyl ethyl ketone peroxide, fine and coarse aggregates are prepared with various filler~binder rations, binder rates and mixing conditions. As a test results, the workability of steel fiber reinforced polyester resin composites are considerably dropped with increasing fly ash-binder ratio and steel fiber volume. And compressive, flexural strength and bending toughness of the composites are remarkably improved with augmenting fiber contents.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05a
• /
• pp.222-225
• /
• 2006

Pull-off test is widely used to evaluate bond performance between concrete and FRP composite. However, reliability of experiment result declines due to many difference between test methods of each national standards. This study analyzed problems of various existing test methods for pull-off test and suggested standardized test method. In addition, since tensile strength of concrete is smaller than bond strength of epoxy resin, maximum bond strength of epoxy resin shall be limited within tensile strength of concrete. Alternative testing method, therefore, which decrease FRP adhesion areas than concrete adhesion areas is suggested to widen test range of bond strength in pull-off test. In the experimental results, bond performance can be estimated up to two times of tensile strength of concrete by reducing FRP adhesion areas by 1/3.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.321-326
• /
• 2000

Many different polymer based concrete materials are known today, but the large setting or hardening shrinkage of polymer concrete is a problem to overcome in their practical applications. The setting shrinkage reaches about five to ren times he drying shrinkage ordinary cement concrete, i.e, 50 to $60\times10^{-4}$. This paper deals with a reduction in the hardening shrinkage of unsaturated polyester resin concrete which is treated with respect to shrinkage-reducing agent content, S/a ratio and catalyst content, and tested for length change during hardening, and flexural and compressive strength. It is show that the change of shrinkage-reducing agent content and S/a ratio affected the length change of the unsaturated polyester resin concrete during hardening.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.45 no.1
• /
• pp.45-54
• /
• 2003

The effects of binder content and silica sand content on the durability characteristics of lightweight polymer concretes are examined. As a result, the flame lingering times using unsaturated polyester resin and non-combustible polyester resin were 60∼120 and 0∼4 seconds respectively, and the combustion lengths were 9∼11 mm and 0∼3 mm, respectively. Thus it is believed that the lightweight polymer concrete was incombustible and the light weight polymer concrete in which non-combustible material was added was perfectly non-combustible. The percent of original mass of lightweight polymer concrete, according to the freezing-thawing experiment, was below 0.3 %, which was much less than that of cement concrete. The pluse velocity, for the case of the binder content 28 %, showed the minimum decreasing rate for the lightweight polymer concrete with silica sand content of 50 %. The higher the binder content, the greater the durability. That is much higher than other material and believed that the freezing-thawing was suppressed by a low absorption.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10b
• /
• pp.1095-1100
• /
• 2000

Concrete structure often exhibit cracks due to the combination of material construction and design error. Minor crack can be tolerated depending on exposure condition, but major cracks are aesthetically unpleasant and affect the durability and safety of the structure. All of the reinforced concrete structure have many inevitable cracks for various reason such as drying shrinkage, heat liberation of cement and over loads. Epoxy resin injection widely used for repairing cracks in concrete is too sensitive to high temperature. Besides, the problem in the epoxy resin injection is the difficulty of quality control after execution. Whereas, Ultra Fine Cement is similar in coefficient of thermal expansion and modulus of elasticity to concrete. The objective of the study is to find out that it is possible for Ultra Fine Cement to be used for repairing cracks in reinforced concrete.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.2
• /
• pp.943-948
• /
• 2013

In this study, the characteristics of polymer-modified mortar which include UM resin, eco-friendly resin, was studied for improving the durability of concrete. UM and cement mortar were mixed with a certain percentage. Eco-friendly UM resin polymer-modified mortar was evaluated by compressive strength, splitting tensile strength, flexural strength, water absorption and chemical resistance experiments. The characteristics of eco-friendly UM resin polymer-modified mortar were evaluated by experiments. Performance of compressive strength and splitting tensile strength were decreasing. On the other hand, performance of flexural strength, water absorption and chemical resistance were increasing. Eco-friendly UM resin polymer-modified mortar reinforced concrete durability performance is excellent.

• KCI Concrete Journal
• /
• v.11 no.3
• /
• pp.89-97
• /
• 1999

The purpose of this research is to investigate the utilization of recycled fine aggregates as a material to apply to a building finished walls or as a decorating material in combination with a polymer. The strengths of two resin mortars using recycled fine aggregates and natural fine aggregates was made. In order to improve the workability and the strength of the resin mortar with recycled fine aggregates, partial replacement of recycled fine aggregates with natural ones was made with the application of various type of fillers. The results, it show that the compressive strength and flexural strength of resin mortar using the recycled fine aggregates were about 70% to 100% of those of resin mortar using natural fine aggregates. It was enough to assure the utilization of the recycled fine aggregates as a material for the production of resin mortar. From the result of partial replacement of recycled fine aggregates with natural ones, the compressive strength was Increased from 5% to 15% and the flexural strength was much as 5% to 20% as a result of 70% substitution It was also found that the use of garnet powder shows a similar tendency in the compressive strength and slag powder does in the flexural strength and tensile strength.

• Advanced Composite Materials
• /
• v.17 no.3
• /
• pp.277-299
• /
• 2008

High quality and expedient processing repair methods are necessary to enhance the service life of bridge structures. Deterioration of concrete can occur as a result of structural cracks, corrosion of reinforcement, and freeze.thaw cycles. Cost effective methods with potential for field implementation are necessary to address the issue of the vulnerability of bridge structures and how to repair them. Most infrastructure related applications of fiber-reinforced plastics (FRPs) use traditional hand lay-up technology. The hand lay-up is tedious, labor-intensive and relies upon personnel skill level. An alternative to traditional hand lay-up of FRP for infrastructure applications is Vacuum Assisted Resin Transfer Molding (VARTM). VARTM uses single sided molding technology to infuse resin over fabrics wrapping large structures, such as bridge girders and columns. There is no work currently available in understanding the interface developed, when VARTM processing is adopted to wrap fibers such as carbon and/or glass over concrete structures. This paper investigates the interface formed by carbon fiber processed on to a concrete surface using the VARTM technique. Various surface treatments, including sandblasting, were performed to study the pull-off tensile test to find a potential prepared surface. A single-lap shear test was used to study the bond strength of CFRP fabric/epoxy composite adhered to concrete. Carbon fiber wraps incorporating Sikadur HEX 103C and low viscosity epoxy resin Sikadur 300 were considered in VARTM processing of concrete specimens.