• Journal of Welding and Joining
• /
• 제34권4호
• /
• pp.28-33
• /
• 2016

The purpose of this study is to evaluate the redistribution of transverse residual stress in the multi-pass FCA butt weld of YP47 in the hatch coaming top plate of ultra large size containership under the tensile cyclic load. In order to do it, the configuration of modified H type specimen including restraint length was first designed to simulate the restraint condition of the butt weld in hatch coaming top plate. FE analysis procedure for evaluating the transverse residual stress was verified by comparing the calculated mean and surface residual stresses with the measured results in the test specimen. After that, the effect of the cyclic load on the redistribution of transverse residual stress was evaluated by comprehensive FEA. From the results, it was found that although the maximum transverse residual stress decreased with an increase in the applied maximum load, the effect of the cyclic load on the mean residual stress is small enough to be negligible. It is because the maximum stress of the ship corresponding to the probability of 10E-8 is less than 70% of yield stress of the weld.

• International Journal of Automotive Technology
• /
• 제7권1호
• /
• pp.69-74
• /
• 2006

Residual stresses are introduced in aluminum cylinder head during quenching at the end of the T6 heat treatment process. Tensile residual stress resulted from quenching is detrimental to fatigue behavior of a cylinder head when it is overlapped with stresses of engine operation load. Quenching simulation has been performed to assess the distribution of residual stress in the cylinder head. Analysis revealed that in-homogeneous temperature distribution led to high tensile residual stress at the foot of the long intake port, where high stresses of engine operation load are expected. Measurements of residual stress have been followed and compared with the calculated results. Results successfully proved that high tensile residual stress, which was large enough to accelerate fatigue failure of the cylinder head, are formed during quenching process at the end of heat treatment at the same critical position. Effect of quenching parameters on the distribution of residual stress in cylinder head has been investigated by choosing different combination of heat treatment parameters. It was demonstrated that changes of quenching parameters led to more homogeneous temperature distribution during cooling and could reduce tensile residual stress at the critical region of the cylinder head used in this study.

• 한국강구조학회 논문집
• /
• 제22권5호
• /
• pp.399-409
• /
• 2010

강구조물은 부식에 의한 단면감소와 이로 인한 내하성능의 저하가 우려된다. 그러나 부식손상이 강부재의 내하성능에 미치는 영향과 잔존 내하성능 평가법은 명확하게 정립되어 있지 않은 실정이다. 본 연구에서는 부식 손상된 지하철 가시설 주형보의 웨브와 플랜지에서 절취한 부식시편의 인장실험을 실시하여, 부식손상이 인장 내하성능에 미치는 영향과 인장 잔존 내하성능 평가법에 대하여 검토하였다. 부식 가시설 주형보로부터 절취한 총 21개의 부식시편은 먼저 화학적 방법에 의해 부식생성물을 제거하고 1mm간격으로 표면형상을 측정한 후 인장실험을 실시하였다. 이러한 인장실험 결과는 주형보의 플랜지에서 절취하여 두께 13mm로 기계 가공한 무부식 기준시편의 인장실험 결과와 비교하여, 잔존두께와 표면형상이 부식강재의 항복하중, 인장하중 및 연신율에 미치는 영향을 정량화하였다. 그리고 부식의 유무에 상관없이 일정한 강재의 극한강도를 이용하여 무부식 등단면 강재와 동일하게 인장응력을 평가할 수 있는 불규칙 변단면 부식강재의 유효두께를 표면형상 측정결과로 산출한 평균잔존두께와 표준편차로 정식화하였다. 또한 이러한 결과를 실무에도 적용할 수 있도록 부식강재의 합리적인 잔존두께 측정간격도 제시하였다.

• Steel and Composite Structures
• /
• 제4권5호
• /
• pp.355-365
• /
• 2004

A new reduction method of residual stress in welding joint is proposed where welded metals are shaken during welding. By an experiment using a small shaker, it can be shown that tensile residual stress near the bead is significantly reduced. Since tensile residual stress on the surface degrades fatigue strength for cumulative damage, the proposed method is effective to reduction of residual stress of welded joints. The effectiveness of the proposed method is demonstrated by the response analysis using one mass model with nonlinear springs.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.668-674
• /
• 2002

Structural integrity assessment is indispensable for preventing catastrophic failure of industrial structures/components/facilities. This diagnosis of operating components should be done periodically for safe maintenance and economical repair. However, conventional standard methods for mechanical properties have the problems of bulky specimen, destructive and complex procedure of specimen sampling. Especially, the mechanical properties at welded zone including weldment and heat affected zone could not be evaluated individually due to their size requirement problem. So, an advanced indentation technique has been developed as a potential method for non-destructive testing of in-field structures. This technique measures indentation load-depth curve during indentation and analyzes the mechanical properties related to deformation such as yield strength, tensile strength and work-hardening index. Also indentation technique can evaluate a residual stress based on the concept that indentation load-depth curves were shifted with the direction and the magnitude of residual stress applied to materials. In this study, we characterized the tensile properties and welding residual stress of various industrial facilities through the new techniques, and the results are introduced and discussed.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2010년도 춘계학술발표대회 초록집
• /
• pp.58-58
• /
• 2010

The purpose of this study is to evaluate the structural safety at the topside weldment of hull structure, which was welded after launching. For it, the variations of residual stress and distortion at the topside weldment with loading conditions such as hull girder hogging bending moment after launching and free initial loading state was evaluated by using FEA. And the maximum stress range at the weldment under design loads specified by classification society was evaluated by FEA. In this case, the residual stress and welding distortion at the topside weldment was assumed to be initial imperfection. In accordance with FEA results, regardless of initial loading condition, tensile residual stress was found. However, the residual stress and welding distortion at the topside weldment produced under hogging condition was less than those of topside weldment under free loading state. That is, the amount of residual stress at the topside weldment decreased with an increase in the amount of tension load caused by hogging condition. It was because the compressive thermal strain at the topside weldment produced during welding was reduced by tensile load. However, the maximum stress range at the topside weldment under maximum hull girder bending moment was almost similar regardless of initial loading condition. So, if the problem related to the soundness of weldment is not introduced by initial load, the effect of initial loading condition during welding on fatigue strength of topside weldment could be negligible.

• 한국지반공학회논문집
• /
• 제35권5호
• /
• pp.43-51
• /
• 2019

현재 국내에서는 비탈면의 안정성 확보를 위해 그라운드 앵커공법을 적용하고 있다. 그라운드 앵커는 시간이 지남에 따라 노후화 및 환경적 영향에 의한 부식, 릴렉세이션, 크립 등으로 긴장력 감소현상이 발생하며, 이로 인해 앵커의 긴장력은 설계앵커력 이하로 감소할 가능성을 내포하고 있다. 이에 국내에서는 정기적인 점검 시 또는 이상 징후가 발생한 앵커를 대상으로 리프트오프 시험을 수행하여 앵커의 잔존긴장력을 확인하고 있으나, 현재 국내 리프트오프 시험기준(국토해양부, 2010)은 수행 및 평가방법이 자세히 명시되어 있지 않은 실정이다. 이에 본 연구에서는 선행연구들을 바탕으로 하중 재하 제하 사이클, 하중 증분방법, 긴장재 긴장 방법 등을 고려하여 리프트오프 시험을 수행하였으며 현장에서의 시공성과 시간적 제한을 고려하여 효율적인 리프트오프 시험 및 평가방법 개선안을 제시하였다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.372-377
• /
• 2002

Residual stress by welding should be reduced because that decreases the reliability on strength of welded structure. The reason is that the total stiffness of structure decreases by non-linear behavior of weldment under external load. The release of residual stress by mechanical loading and unloading is often performed in the fabrication of box structure for steel bridge. The proper degree of loading and unloading is significant at release method of residual stress by mechanical loading because that degree is changed by material and geometric shape of welded structure. Therefore, the simulation model that could exactly analyze the release of residual stress by mechanical loading is to be necessary. This simulation model should be established on the based of variable and accurate measurement data. In this study, the non-linear behavior of weldments under external loading and unloading, such as the decrease and increase of structure stiffness, was investigated by monitoring of nominal stress and strain. Tensile loading and unloading test under variable load was performed and the proper degree of stress relaxation was measured by sectioning technique using strain gauge.

• International Journal of Korean Welding Society
• /
• 제2권1호
• /
• pp.40-44
• /
• 2002

Residual stress by welding should be reduced because that decreases the reliability on strength of welded structure. The reason is that the total stiffness of structure decreases by non-linear behavior of weldment under external load. The release of residual stress by mechanical loading and unloading is often performed in the fabrication of box structure for steel bridge. The proper degree of loading and unloading is significant at release method of residual stress by mechanical loading because that degree is changed by material and geometric shape of welded structure. Therefore, the simulation model that could exactly analyze the release of residual stress by mechanical loading is to be necessary. This simulation model should be established on the based of variable and accurate measurement data. In this study, the non-linear behavior of weldments under external loading and unloading, such as the decrease and increase of structure stiffness, was investigated by monitoring of nominal stress and strain. Tensile loading and unloading test under variable load was performed and the proper degree of stress relaxation was measured by sectioning technique using strain gauge.

• 대한기계학회논문집A
• /
• 제20권5호
• /
• pp.1543-1551
• /
• 1996

The static tensile load bearing capability of as adhesively-bonded tubular single lap jint that is calculated usign the linear mechanical properties of adhesive is usually far from the experimentally determined because the majority of the load transfer of the adhesively-bonded jointd is accomplished by the nonlinear behavior of the rubber-toughened eoxy adhesive. In this paper, both the nonlinear mechanical properties and the fabrication residual thermal stresses of adhesive were included in the calculation of the stresses of adhesively-bonded joints. The onlinear tensile properties of adhesive were approximated by an exponential form which was represented by the initial tensile modulus and ultimate tensile stength of adhesive. The stress distribution in the adhesive were calculated by applying the load obtained from the tensile tests. From the tensile tests and the stress analysis of adhesively-bonded hoints, the failure model for adhesively-bonded tubular single lap joints was proposed.