• 한국항공우주학회지
• /
• 제31권3호
• /
• pp.79-84
• /
• 2003

홀 확장법은 홀 주위에 압축 잔류응력층을 생성시킴으로서 균열 발생을 지연시키는 방법으로 항공산업 분야에서 널리 사용되고 있다. 홀 확장 잔류응력의 분포는 홀 확장률, 맨드럴 삽입방향, 재료 물성치 등 여러 가지 홀 확장 피라미터에 따라 달라진다. 홀 확장 잔류응력층의 정확한 파악은 항공산업의 실제 설계에 있어서 매우 중요함에도 불구하고 이에 대한 연구는 상대적으로 부족하였다. 본 연구에서는 유한요소해석을 통하여 두 개의 인전한 홀에 홀 확장법을 적용하는 경우 대한 잔류응력 분포를 구하였다. 연구 결과 두개 홀에 동시에 홀 확장을 하는 경우가 순차적으로 홀 확장으로 하는 경우보다 더 유리한 잔류응력 분포를 얻을 수 있었다.

• 대한기계학회논문집B
• /
• 제35권11호
• /
• pp.1219-1227
• /
• 2011

최근 생활 환경의 변화로 혈관계 질병으로 고통 받는 사람들이 늘어가고 있다. 이에 따라 질병을 치료하기 위해 여러 가지 시술을 하게 되는데 있어서 혈관의 역학적인 분석과 해석이 확보되어야 한다. 본 논문에서는 초탄성 이론을 기초로 하여 탄성 대변형에서의 혈관의 역학적인 거동에 대해 알아 보았다. 이를 통하여 정상혈압과 고혈압일 때 혈관에 작용하는 응력과 열림각으로 나타낼 수 있는 잔류 응력의 효과가 각 방향 응력분포에 미치는 영향에 대해 연구하였다. 그 결과 잔류응력 효과를 적용시켰을 때 혈관 벽내에 작용하는 최대응력은 잔류응력 효과가 없을 경우와 비교하여 약 50%응력 감소가 나타남을 확인할 수 있고, 고혈압의 경우 정상혈압일 때보다 2배정도의 큰 응력이 혈관벽에 작용함을 확인 할 수 있었다.

• 한국해양공학회지
• /
• 제4권1호
• /
• pp.81-87
• /
• 1990

Fatigue crack closure levels based on the behavior of residual displacements on crack surfaces, are determined analytically according to the microscopic crack closure mechanisms, i.e., whether the first contact of crack surfaces takes place at the very crack tip or on the surfaces near the tip. The comparative analysis on the two models is carried out empirically by the constant amplitude fatigue tests on 2024-T3 aluminum alloy plate, and it shows that under negative stress ratio, the case of the first contact at crack tip gives better agreement with the experimental results than the other.

• 한국해양공학회지
• /
• 제4권1호
• /
• pp.87-87
• /
• 1990

Fatigue crack closure levels based on the behavior of residual displacements on crack surfaces, are determined analytically according to the microscopic crack closure mechanisms, i.e., whether the first contact of crack surfaces takes place at the very crack tip or on the surfaces near the tip. The comparative analysis on the two models is carried out empirically by the constant amplitude fatigue tests on 2024-T3 aluminum alloy plate, and it shows that under negative stress ratio, the case of the first contact at crack tip gives better agreement with the experimental results than the other.

• 대한기계학회논문집A
• /
• 제23권7호
• /
• pp.1245-1252
• /
• 1999

The sliding wear behavior of $Al_2O_3/NiCr$ coating deposited on steel(SM45C) was investigated under lubrication. The parameters of sliding wear are normal loads, coating thickness. As a result, the wear resistance of $Al_2O_3/NiCr$ coating was remarkably greater than that of $Al_2O_3$ coating. The optimized coating thickness was found to be $300{\mu}m$ to ensure good anti-wear. The bond coating played important role in decreasing residual stress. The residual stress had much influence on wear mechanism. These results were correlated with the stress state of coating and the microstructure of coating.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.256-261
• /
• 2007

The purpose of this study is to investigate the effect of shot peening on the fatigue strength and fatigue life of two kinds of aluminum alloys. The fatigue strength behavior of aluminum alloys were estimated by the stress ratio and shot velocities. The fatigue life and strength increased with increasing the test shot velocity. However, at the shot velocity range between 50m/s and 70m/s, the compressive residual stress phenomena were observed in test conditions of different shot velocity. The optimal shot velocity is acquired by considering the peak values of the compressive residual stress, dislocations, brittle striation, slip, and fisheye on the fracture surface of test specimen. It was observed from the SEM observation on the deformed specimen that the brittle striation, fisheye were showed in the intergranular fracture structure boundaries at the this velocities. Therefore, fatigue strength and fatigue life would be considered that shot velocity has close relationship with the compressive residual stress.

• 비파괴검사학회지
• /
• 제32권2호
• /
• pp.149-154
• /
• 2012

용접구조물에는 외력이 부가되기 이전에 잔류응력이 걸려 있으므로 용접잔류응력 크기 및 분포 상태는 취성파괴, 피로강도, 응력부식균열, 좌굴, 시효변형과 같은 다양한 형태의 손상에 직접적으로 영향을 끼쳐 잔류응력을 정량적으로 해석하기 위한 지속적인 연구가 필요한 실정이다. 본 논문은 비파괴적인 기법 중 레이저를 이용한 전자처리스페클패턴 간섭법을 이용하여 평판 용접시험편의 외부하중에 따른 전체 거동에 잔류응력의 측정 기법을 제시하고자 한다. 용접시험편에 인장 하중을 가하였을 때, 이를 전자처리패턴스페클 기법을 이용하여 측정하였다. 측정된 결과로부터 용접시험편의 모재부와 용접부의 변형률을 측정하고, 이를 이용하여 탄성계수를 측정하였다. 본 논문은 전자처리스페클패턴 간섭법으로 용접시험편의 용접부와 모재부의 변형률의 차이를 이용하여 잔류응력 값을 산출하는 식을 제시하였고, 이를 수치적으로 계산하여 잔류응력 값을 산출하였으며 측정 결과, 모재부에 비해 용접부의 탄성계수가 약 3.7배 높은 약 8.46 MPa로 측정되었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1086-1091
• /
• 2003

The problem of residual stresses and fatigue behavior in welded structures is the main concern of welding research fields. The residual stresses and distortions of structures by welding exert negative effect on the safety of mechanical structures. Postweld heat treatment is usually carried out to relieve this residual stresses of welded joints. In this paper the influence of postweld heat treatment on fatigue life of butt-welded joint was investigated. To predict the effect of PWHT, an analytical model is developed by finite element and local strain approach and the result of fatigue life analysis is compared to experimental results. It is demonstrated that fatigue life estimates closely approximate the experimental results and PWHT provides some increase of fatigue lives in long-life fatigue region and no increase in short-life fatigue region because of the residual stress relaxation under tensile loads.

• Journal of Mechanical Science and Technology
• /
• 제20권10호
• /
• pp.1646-1652
• /
• 2006

A model of mechanical behavior of microcantilever due to intrinsic strain during deposition of MEMS structures is derived. A linear ordinary differential equation is derived for the beam deflection as a function of the thickness of the deposited layer. Closed-form solutions are not possible, but numerical solutions are plotted for various dimensionless ratios of the beam stiffness, the intrinsic strain, and the elastic moduli of the substrate and deposited layer. This model predicts the deflection of the cantilever as a function of the deposited layer thickness and the residual stress distribution during deposition. The usefulness of these equations is that they are indicative of the real time behavior of the structures, i.e. it predicts the deflection of the beam continuously during deposition process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1994년도 춘계학술대회 논문집
• /
• pp.167-174
• /
• 1994

The creep behavior and creep fracture of alumina at high temperature were investigated under four point flexural test. The steady-state creep behavior was observed at low bending stress and the primary creep until fracture was observed at high bending stress. The loading history of bending stress did not affect on the steady-stated creep rate. Intergranular fracture was dominant for fracture of alumina at room and high temperature. However, transgranular fracture was dominant on creep fracture of alumina under high temperature by nuclueation and growth of microcracks due to residual flaws or cavities in the material.