• 대한기계학회논문집A
• /
• 제23권7호
• /
• pp.1085-1093
• /
• 1999

Thickness effects of coupling agent on residual bending stress were investigated in $Polyimide/SiO_2$ joints during thermal cycling. Thickness and peel strength of $\gamma$-APS coupling agent were measured and correlated with solution concentration and residual bending stress. The variation of residual bending stress with temperature was also measured for various thicknesses of the coupling agent. Finite element results were compared with experimental data for residual bending stress in $Polyimide/SiO_2$ joints.

• 대한기계학회논문집
• /
• 제18권7호
• /
• pp.1664-1673
• /
• 1994

As a fundamental study on effects of thermal-cycles on residual stress of ceramics/metal joints, residual stresses in $Si_3N_4$/SUS304 joint specimens were measured before and single thermal-cycle by X-ray diffraction method and finite element method(FEM). The residual stress was found to increase after single thermal-cycle, which was agreeable with the results of residual stress measurement by X-ray diffraction method and residual stress analysis by finite element method. After the residual stress measurement, 4-point bending tests were performed. The relationship between the bending strength, the thermal-cycle temperature and hold time was examined. The bending strength was found to decrease with the increase of residual stress in linear relation.

• 대한기계학회논문집A
• /
• 제24권2호
• /
• pp.279-289
• /
• 2000

Residual stress induced in U-bending and tube-to-tubesheet joint processes of PWR's row-1 heat exchanger tube was measured by X-ray method and Hole-Drilling Method(HDM). Compressive residual stresses(-) at the extrados surface were induced in U-bending, and its maximum value reached -319 MPa in axial direction at the position of $\psi$ = $0^{\circ}$. Tensile residual stresses(+) of $\sigma_{zz}$ = 45 MPa and $\sigma_{\theta\theta}$ = 25 MPa were introduced in the intrados surface at the position of $\psi$ = $0^{\circ}$. Maximum tensile residual stress of 170 MPa was measured at the flank side at the position of $\psi$ = $90^{\circ}$, i.e., at apex region. It was observed that higher stress gradient was generated at the irregular transition regions (ITR). The trend of residual stress induced by U bending process of the tubes was found to be related with the change of ovality. The residual stress induced by the explosive joint method was found to be lower than that by the mechanical roll method. The gradient of residual stress along the expanded tube was highest at the transition region (TR), and the residual stress in circumferential direction was found to be higher than the residual stress in axial direction.

• 한국세라믹학회지
• /
• 제33권2호
• /
• pp.127-134
• /
• 1996

The thermal residual stresses were estimated for brazed Si3N4/S.S.316 joints with Cu/Mo multi-interlayers using FEM, and their bending strengths at room temperature were measured for various interlayer configura-tions. The Cu, Mo multi-interlayer decreased the maximum residual stress in Si3N4 and caused the residual stress redistribution rsulting in the high residual stress at Mo interlayer. The stress distribution in the joints as well as the maximum residual stress in silicon nitride were found to be main factors for determining bending strengths and Weibull modulous of the joints. The bending strength of the brazed Si3N4/S.S.316 joints with specific Cu, Mo multi-interlayer system were found to be above 400 MPa.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.637-642
• /
• 2008

Autofrettage analysis of a bend in the fuel injcetion pipe has been performed to investigate the distribution of residual stresses due to pipe bending and autofrettage processes. The pipe bending was simulated by metal forming analysis using finite element method, and residual stress distribution after bending was found. Autofrettage following the pipe bending was performed by applying the hydrostatic internal pressures of 603 MPa, 535 MPa, 500 MPa on the pipe bend, corresponding to theoretical 26 %, 14 %, 9 % overstrain levels, respectively. Residual stress distributions due to bending and autofrettage were evaluated.

• Steel and Composite Structures
• /
• 제29권2호
• /
• pp.161-173
• /
• 2018

Point bending is often used for cambering and curving structural steel girders. An analytical solution, applicable in the elasto-plastic range only, that relates applied loads to the desired curve was recently developed for inducing horizontal curves using four-point bending. This solution does not account for initial residual stresses and geometric imperfections built-in hot-rolled sections. This paper presents results from a full-scale test on a hot-rolled steel section curved using four-point bending. In parallel, a numerical analysis, accounting for both initial geometric imperfections and initial residual stresses, was carried out. The models were validated against the experimental results and a good agreement for lateral offset and for strain in the elasto-plastic and post-plastic ranges was achieved. The results show that the effect of initial residual stresses on deformation and strain is minimal. Finally, residual stresses due to cold bending calculated from the numerical analysis were assessed and a revised stress value for the service load design of the curved girder is proposed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 추계학술대회 논문집
• /
• pp.481-482
• /
• 2007

• 한국생산제조학회지
• /
• 제7권5호
• /
• pp.120-126
• /
• 1998

Second step shot peening was applied on both smooth specimen and U-notch specimen in order to investigate the stress distribution and the improvement in fatigue strength. Various experiments and measurements such as rotary bending fatigue test and the measurement of compressive residual stress were performed. The results showed that the fatigue strength of second step shot peened specimens increased by 34 percent compared to that of unpeened ones. Compressive residual stress also considerably increased, which resulted in the increase of fatigue strength. finite element analysis showed that shot peening is effective in decreasing the bending stress by external force. The effectiveness of shot peening in reducing the compressive residual stress was anticipated by the superposition of the concentrated stress and the compressive residual stress.

• 대한기계학회논문집A
• /
• 제22권1호
• /
• pp.238-246
• /
• 1998

Surface residual stresses as well as wall thickness and ovality changes after U-bending process on UNS N06690 row-1 heat exchanger tubes, were estimated. Surface residual stresses were measured by Hole Drilling Method(HDM), calculating the stresses from relieved strains of 3 rosette strain gages. After bending of the tubes, dimensional tolerances for wall thickness and ovality were satisfied with ASTM requirements. Residual stresses at the extrados were introduced with compressive stress(-) by bending operations, and its maximum value reached-319 MPa in axial direction at ${\phi}=0^{\circ}$ in position. Tensile residual stresses(+) of ${\sigma}_zz=45$ MPa,${\sigma}_zz=25$ MPa were introduced in the intrados surface at position of ${\phi}=0^{\circ}$ Maximum tensile residual stress of 170 MPa was detected on the flank side at position of ,${\phi}=95^{\circ}$i.e., at apex region. It appeared that higher stress gradients were generated at the irregular transition regions. In the trend of residual stress changes with U-bend position, the extrados is related with the changes of ovality and the intrados is related with the changes of wall thickness.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.326-329
• /
• 2009

In order to analyze the effect of leveling conditions on residual stress evolution of hot rolled high strength steels, a numerical algorithm was developed. It was able to implement the effect of plastic fraction (intermesh) in leveling, line tension, work roll bending, and initial residual stress and curl distribution. The effect of work roll bending on residual stress and curl were studied by using the developed program. The validity of simulated results was verified from comparison with the experimentally measured residual stress and curl in a sheet.