• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.4
• /
• pp.65-70
• /
• 2010

A small unmanned aerial vehicle(UAV), which uses a propulsion system consisting of electric motor and battery, weighs less than 8 kg, capable of hand launch. Because it is easy to operate and able to transmit image information in real time, the use of small UAV has been increasing. However, very few analysis methods or analysis results on flight performance of the small UAV have been known so far. In this paper, the performance analysis methods of a small UAV, which is manufactured to study an electric powered UAV, are suggested and their results are achieved. Aerodynamic data of the vehicle are obtained by making use of gliding performance from actual flight test, and required thrust and required power by flight speed are predicted. In addition, the methods to predict range and endurance in case of using battery as power source are suggested and their results are achieved.

• Journal of Aerospace System Engineering
• /
• v.13 no.1
• /
• pp.47-53
• /
• 2019

To improve an aerodynamic characteristic of the eVOTL aircraft, Korea Aerospace Research Institute (KARI) performed a validity test of the cross-rotating propeller technology. First, CFD analysis was carried out and an idea of the cross-rotating propeller to imply on a multi-copter confirmed with a commerce pitch control multi-copter that has two different blades, 0.11 and 0.21 m. After verifying the idea, a multi-copter with about 3 kg maximum take-off weight (MTOW) was custom designed to complete a ground test to measure thrust and noise. The test was performed with 15 and 22 in. propellers at the identical tip speed. The test results show that the 22 in. propeller with the cross-rotating technology required about 30 % less power and reduced 3~5 dB aerodynamic noise as compared to 15 in. propeller without cross-rotating.

• Journal of Advanced Navigation Technology
• /
• v.25 no.3
• /
• pp.203-210
• /
• 2021

In many metropolitan cities around the world, ground and underground transportation networks are saturated due to urbanization. In addition, regulations on carbon emissions to prevent global warming are becoming stricter, and eVTOL, which will be operating in complex cities, is gaining popularity as the next generation of eco-friendly transportation. In this study, the hover lift efficiency and disc loading of eVTOLs for each type were calculated by classifying eVTOLs into following types: multicopter, lift+cruise, and vectored thrust. In addition, using the aerodynamic analysis programs OpenVSP, Fluent and Javaprop, the specific battery energy required for the smooth operation of eVTOL, which will be realized in the near future, was calculated and analyzed base on reports published by Uber and airworthiness authorities of each country.

• Journal of Astronomy and Space Sciences
• /
• v.40 no.1
• /
• pp.35-44
• /
• 2023

Surveillance and reconnaissance intelligence in the space domain will become increasingly important in future battlefield environments. Moreover, to assimilate the military provocations and trends of hostile countries, imagery intelligence of the highest possible resolution is required. There are many methods for improving the resolution of optical satellites when observing the ground, such as designing satellite optical systems with a larger diameter and lowering the operating altitude. In this paper, we propose a method for improving ground observation resolution by using an optical system for a previously designed low orbit satellite and lowering the operating altitude of the satellite. When the altitude of a satellite is reduced in a circular orbit, a large amount of thrust fuel is required to maintain altitude because the satellite's altitude can decrease rapidly due to atmospheric drag. However, by using the critical inclination, which can fix the position of the perigee in an elliptical orbit to the observation area, the operating altitude of the satellite can be reduced using less fuel compared to a circular orbit. This method makes it possible to obtain a similar observational resolution of a medium-sized satellite with the same weight and volume as a small satellite. In addition, this method has the advantage of reducing development and launch costs to that of a small-sized satellite. As a result, we designed an elliptical orbit. The perigee of the orbit is 300 km, the apogee is 8,366.52 km, and the critical inclination is 116.56°. This orbit remains at its lowest altitude to the Korean peninsula constantly with much less orbit maintenance fuel compared to the 300 km circular orbit.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2342-2347
• /
• 2011

This paper introduces the performance test of the prototype vehicle, which will be in operation for Urban Maglev Program. While common trains with steel wheels use rotary induction motors for propulsion, maglev trains gain thrust force from linear induction motors maintaining the constant airgap with levitation electromagnets. Therefore, not only the behavior of the linear induction motor should be well understood, but also the way of propulsion that minimizes its effect on the levitation system should be took into account. Performance test procedures of maglev trains are proposed and carried out, and the characteristics of acceleration and deceleration are verified to agree with the design criteria. Tests are mainly performed on the linear section of the test line, and the driving characteristics on the section with a 6‰ incline are examined additionally. As a result, the performance of the prototype vehicle in the reverse operation can satisfy the requirement about the acceleration and deceleration, 4.0$m/s^2$. And, the design modifications of the commercial vehicle and the performance specifications required on the demonstration line are investigated.

• The KSFM Journal of Fluid Machinery
• /
• v.5 no.4 s.17
• /
• pp.11-18
• /
• 2002

A turbopump system composed of two pumps and one turbine is considered. The turbine composed of a nozzle and a rotor is used to drive the pumps while gas passes through the nozzle and potential energy is converted to kinetic energy, which forces the rotor blades to spin. In this study, an aerodynamic design of turbine system is investigated with some pre-determined design requirements (i.e., pressure ratio, rotational speed, required power, etc.) following Liquid Rocket Engine (L.R.E.) system specifications. For simplicity of turbine system, impulse-type rotor blades for open-type L.R.E. have been chosen. Usually, the open-type turbine system requires low mass flow-rate compared to close-type system. In this study, a partial admission nozzle is adopted to maximize the efficiency of the open-type turbine system. A design methodology of turbine system was introduced. Especially, partial admission nozzle was designed by means of simple empirical correlations between efficiency and configuration of the nozzle. Finally, a turbine system design is presented for a 10 ton thrust level of L.R.E.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.8
• /
• pp.747-752
• /
• 2007

Domestic satellite development programme is generally classified into two categories: COMS as GEO satellite and KOMPSAT as LEO one. Each satellite has the on-board propulsion system fulfilling its own mission requirements. The COMS propulsion system provides the thrust and torque required for the insertion into GEO, attitude and orbit control/adjustment of spacecraft. It is the well-known Chemical Propulsion System(CPS) using bipropellants. On the other hand, the monopropellant propulsion system is employed in KOMPSAT, and its main role is on-station attitude control excluding the orbit transfer function. In this study, these two representative propulsion systems are compared and analysed as well, in terms of essential differences and important characteristics.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1057-1058
• /
• 2011

This paper deals with finding the optimal ratio of height and length of Single-Sided Linear Induction Motors (SLIM) using Finite Element Method (FEM) for magnetic field analysis coupled with optimal design methodology. For effective analysis, FEM is conducted in time harmonic field which provides steady state performance with the fundamental components of voltage and current. The ratio of height to length providing the required output power is obtained by Response Surface Methodology (RSM) and optimal values are presented by the variation in output power. When output power is small, the ratio is high and as the power increases, the ratio shows a converged value. Considering the general application of linear motors, using a small ratio can be limiting, however, the shape ratio for maximum thrust can be identified.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.10
• /
• pp.92-98
• /
• 2006

An 1 lbf of NASA standard monopropellant thruster, MRE-1, is used for KOMPSAT (Korea Multi-Purpose Satellite) which is launched in 2006 and provides reliable and cost-effective means for attitude and maneuvering control system. The monopropellant thruster obtains required thrust by thermal decomposition process of propellant through catalyst bed. During firing, the decomposition plays a role of a heat source that may occur an excessive radiation heat transfer to peripheral structures and electronics in relatively low temperature condition.Therefore, the radiation heat shield is needed to prevent the critical radiative heat exchange between thruster and satellite during firing. This paper summarizes an overall development process of radiation heat shield from the design engineering up to the manufacturing.

• Journal of Pharmaceutical Investigation
• /
• v.32 no.4
• /
• pp.327-330
• /
• 2002

Alginate based polymeric matrices were designed for controlled release and stabilization of cefaclor in gastrointestinal fluid. Cefaclor is known to be acid stable and subjected to be degraded at neutral and alkaline pHs. In order to achieve an effective release profile of cefaclor in gastrointestinal tract, a particular strategy in dosage form design should be required from the view point of maintaining its activity. The amphiphilic nature of cefaclor allowed its controlled release using ionic polymers based on ionic interaction between the drug and polymers. The thrust of this study was to develop a technique that delivers cefaclor keeping effective release rate in the intestinal tract. Considering the fast degradation of cefaclor in the intestinal fluid, the matrices were designed to release surplus amount of cefaclor. The alginate based matrices demonstrated increase in release rate in the simulated intestinal fluid, which was favorable to compensate the degraded portion of cefaclor. In addition, stabilization of cefaclor in the intestinal fluid was obtained by employing citric acid that provides an local acidic environment. The matrices might be valuably used for the development of an oral cefaclor dosage form.