• Journal of ILASS-Korea
• /
• v.20 no.2
• /
• pp.95-100
• /
• 2015

Lower recirculated gas temperature at EGR system reduces NOx and PM emissions. However, EGR Cooler can be polluted by PM generated from recirculated EGR gas, and it reduces cooling efficiency and the amount of EGR gas simultaneously. The SECFR(Steam EGR Cooler Fouling Remover) system which uses the evaporated washer fluid steam caused by high temperature of EGR gas was manufactured for removing fouling generated on the cooler surface. Since an injection pressure of wind shield washer fluid in the vehicle is approximately 0.5 bar, it is not enough to atomize the injected washer fluid. Thus, it is necessary to apply a method to atomize the washer fluid. In this study, the impinging plate was used to promote the atomization of spray washer fluid for the purpose of apply SECFR system to vehicles and measured the DAR(Droplet Area Ratio) and DUI(Droplet Uniformity Index) through the spray visualization.

• 전자공학회논문지 IE
• /
• v.49 no.2
• /
• pp.24-29
• /
• 2012

The sounds of exhaust emissions of automobiles are independent sound sources which are nothing to do with voices. We have no information for the sources of voices and exhaust sounds. Accordingly, Independent Component Analysis which is one of the Blind Source Separaton methods was used to segregate two source signals from each mixed signals. Maximum Likelyhood Estimation was applied to the signals came through the stereo microphone to segregate the two source signals toward the maximization of independence. Since there is no clue to find whether it is speech signal or not, the coefficients of the slope was calculated by the autocovariances of the signals in frequcency domain. Noise remover for speech signals was implemented by coupling the two algorithms.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.02a
• /
• pp.136-143
• /
• 2002

Warm draw die technique which is one of the new forming technologies to improve formability of sheet metal is applied to the cylindrical and square cup drawing of stainless-aluminum clad sheets. In experiments the temperature of die and blank holder is varied from room temperature to $180^{\circ}C$, while the punch is cooled by circulation of coolant to increase the fracture strength of workpiece on the punch comer area. Test materials chosen for experiments are STS304-A1050-STS304 clad sheets. Teflon film as a lubricant is used on both sides of a workpiece. The limit drawing ratio and relative drawing depth as well as quality of drawn cups(distribution of thickness)are investigated and validity of warm drawing process is also discussed. No separation between each laminated material after drawing occurred through inspection by microscope as well as application of penetrant remover and bond strength test. Therefore, warm forming technique was confirmed to give better results in deep drawing of stainless clad sheet metal.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.05b
• /
• pp.123-126
• /
• 2009

This study is analyzed the effects of the number of use of aluminum form surface coating material on surface quality of concrete. The results can be summarized as follows. Surface roughness showed larger values with increase in the number of use. Values were larger in UP and AL compared to PE. While found to have bad influence on concrete surface quality, PA and W showed most excellent values for roughness. The number of surface pores increased with increasing number of use, and the number of pores on concrete surface was reduced by applying a remover. In terms of type of surface coating material, PA and W showed smallest number of pores in comparison to PE. In order to comprehensively improve surface quality of concrete, parallel use of PA coating material and remover is deemed most appropriate.

• Corrosion Science and Technology
• /
• v.17 no.6
• /
• pp.257-264
• /
• 2018

Anti-graffiti coatings have become more important. These layers must guarantee excellent corrosion protection properties, and graffiti must be easily removable, without reducing protection and aesthetic properties. In this study, anti-graffiti and corrosion behavior of two anti-graffiti polyurethane powder coatings were studied. These layers were deposited on aluminum substrate, with two different surface finishes, smooth, and wrinkled. The action of four different removers are investigated. Graffiti were drawn on coatings by means of red acrylic spray paint. Methyl-ethyl-ketone (MEK) and a "commercial" remover were the most effective solvents, in terms of graffiti removal capability, producing limited change in aesthetical surface aspect for smooth finishing. The wrinkled surface was less resistant. Corrosion protection properties, after removal action and contact with the remover, were evaluate by electrochemical impedance spectroscopy. After approximately 5 hours, coatings were no longer protective due to formation of defects. To simulate the weathering effect, UV-B cyclic test (4 hours of UV exposure followed by 4 hours of saturated humidity at $50^{\circ}C$) were performed for 2000 hours. Gloss and color changes were measured, and electrochemical impedance spectroscopy measurements were performed after aging and graffiti removal.

• Journal of Korean Ophthalmic Optics Society
• /
• v.15 no.1
• /
• pp.55-60
• /
• 2010

Purpose: We investigated the changes of plastic lens after etching of coating films by comparing uncoated lens. Methods: CR-39, middle index and high index lenses of 0 (zero) diopter were etched at $80^{\circ}C$ and room temperature using a coating remover, and then changes of refractive power, transmittance and surface morphology were investigated. Results: There were no differences in refractive power and transmittance between uncoated and etched lenses. The etching rate was similar in both CR-39 and middle index lens, but in the case of high index lens, it was slower and less steady than the others. From the SEM observation of lens surface, etching damage was found out on the surface of etched lens. It was shown the least damage in middle index lens but the most damage in high index lens. Conclusions: If the etching of coating films is demanded on condition that the surface of ophthalmic lenses are not damaged, a using of most adequate coating remover based on lens material should be considered, and a caution for proper etching conditions is required.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.38 no.4
• /
• pp.213-221
• /
• 2022

Purpose: The efficacy of the amount of sealer in the root canal and two retreatment NiTi file systems in removing filling materials. Materials and Methods: Extracted premolars with a single root canal were selected for this study. After access opening and root canal preparation up to size #40/.06, the specimens were randomly divided into four groups. Gutta percha (GP) tapers of .06 or .04 were used for each group and filled using a single-cone filling technique with CeraSeal, a calcium silicate-based sealer. Each group was retreated either using the ProTaper Universal Retreatment System (PTUR) or the Hyflex Remover (HR). The time taken to remove the filling material, the amounts of apically extruded debris, and canal cleanliness were measured and compared. Results: The amount of sealer did not affect the efficiency when removing the filling materials. However, the filling material was removed faster in the HR group than in the PTUR group. Two types of NiTi files showed similar retreatment effects in the amounts of apically extruded debris and in the degree of canal cleanliness. Conclusion: The amount of sealer in canal filling had no significant effect on retreatability. Retreatment with HR removed filling materials is faster than PTUR. There was no difference in other removal efficiencies according to the type of retreatment NiTi file.

• Natural Product Sciences
• /
• v.3 no.2
• /
• pp.135-140
• /
• 1997

The methanolic extract of Lysimachiae christinae Herba, which has been used for diuretic, calculi remover and jaundice remedy in oriental countries, was found to possess analgesic and antiinflammatory effect in Freund's complete adjuvant treated rat. From ethyl acetate fraction of the herb a phenyl propanoid isoferulic acid was isolated as an active principle.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11c
• /
• pp.578-585
• /
• 2000

Geometrical characteristics of fresh red pepper(Capsicum annuum L.) were measured and indexed to define some important geometrical characteristics, and malformation of body and fruit stalk which are necessary for the design of the equipments for cutting, spreading and alignment of red pepper in developing a fruit stalk remover of fresh red pepper. The effects of bending of body and fruit stalk on the equipments of cutting, spreading and alignment were studied. The maximum lengths of some parts of fresh red pepper were found to be 180 mm, 125 mm, 144 mm, 67 mm and 76 mm for the body, the bent part of body, the fruit stalk, the bent part and the straight part of fruit stalk, respectively. The fresh red pepper with bending indices more than 0.4 and 0.3 for the body and the fruit stalk, respectively, was defined to be malformed based on the result of cutting rate using cutting unit; while the other ones to be normal in shape. Based on this, among the total fresh red peppers tested, 47%, 40% and 20% were found malformed for the body, the fruit stalk, and for both of the body and the fruit stalk. Malformed red peppers were poorer in spreading and alignment than normal ones, and the processed quantity was decreased with increased feed rate. The required time for the malformed peppers to pass on the alignment plate inclined at 30 increased rapidly at 8.3 Hz with increased feed rate. For the fresh red peppers with average moisture content of 85%,w.b., the maximum tensile strength between fruit stalk and body was 88.1 N; the maximum cutting resistances were 92.1 N and 94.9 N for the fruit stalk-calyx joint and body, respectively. Average coefficients of static friction were 0.99, 0.62, 0.59 and OJ, respectively, for the surfaces of rubber, galvanized iron, acryl and plywood.

• Journal of the Korea Computer Industry Society
• /
• v.2 no.10
• /
• pp.1317-1328
• /
• 2001

The existing swearing remover programs could not have blocked even slightly transformed swearings because of their input blocking properties. To overcome these defects, this paper implemented a supervising program which analysize and remove/replace swearings on web board. For this purpose this paper first classified the patterns of swearings on web board and then implemented a tokenizer which can analysize those patterns. The module tokenizing and removing/replacing swearings on each web board was implemented as a thread so that it could be parallely controlled. As a result of running this Program on some web boards , we found out it had detected almost of the swearings as 91.9% of recall but it could not meet our purpose sufficiently on morphological transformed swearings and swearings in context. So the studies will be continued about processing on morphological ambiguous words, ambiguous words in meaning and sweaings in context by extracting this program's manual mode. We expect this program could induce the users to proper usage of words and replace the manual works of web board managers in schools, public bodies, broadcasting stations etc.