• Journal of Korean Society on Water Environment
• /
• v.21 no.2
• /
• pp.118-124
• /
• 2005

The oxygen solubilized device(O.S.D) and standardized microorganism culture system is more efficient than physical and chemical purification techniques in closed water. This study was to determine how the O.S.D and standardized culture system is efficient in purification capacity in closed water based on the lab scale and pilot plant. In the batch test, inducing the quantitative results from pilot plant operation condition, removal efficiency of COD and TN were about 48.3% and 35% respectively, while SS and chlorophyll-a were 94.9% and 68.7%. The pilot plant results showed that suspended solid(SS) and chlorophyll-a removal efficiency were 60% and 59% respectively, due to coagulation characteristics by standardized culture. Total nitrogen(TN) and total phosphorus(TP)showed good effect for the purification of target pond water quality from field data. Additionally, released velocity was determined in control condition of $5.31mgPO{_4}^{3-}{\cdot}m^{-2}{\cdot}day^{-1}$ and $2486.8mgCOD{\cdot}m^{-2}{\cdot}day^{-1}$. Otherwise, phosphate and COD reflux in the aeration and microorganism condition was showed $-9.95mgPO{_4}^{3-}{\cdot}m^{-2}{\cdot}day^{-1}$ and $-397.88mgCOD{\cdot}m^{-2}{\cdot}day^{-1}$. This technology is the most effective not only removal of SS and chlorophyll-a but also control of phosphate and COD release which is very important phenomena in evaluating water quality in closed water like a reservoir and pond.

• Clean Technology
• /
• v.2 no.1
• /
• pp.80-95
• /
• 1996

A mathematical model has been developed for simulating the spray dryer absorber (SDA) used in semi-dry flue gas desulfurization process. Fundamental equations include the component mass and heat balances in both gas and droplet phases and the equation of motion for a single droplet. The model developed described the pilot-plant data much better than the existing SPRAYMOD-M model. The effect of the process variables, whose values were chosen within the operation limits of the actual pilot plants, on % $SO_2$ removal or conversion of the sorbent were calculated, and discussed in terms of $SO_2$ absorption rate, the residence time of flue gas, the velocity and drying time of droplets. Finally, the % $SO_2$ removal was calculated with two independent process variables and the results were shown on three-dimensional or two-dimensional diagrams with the lines of constant % $SO_2$ removal, so that they can be easily applied to preliminary design of the SDA.

• Journal of the Semiconductor & Display Technology
• /
• v.7 no.4
• /
• pp.29-33
• /
• 2008

Rapid increase of integrity for recent semiconductor industry highly demands the development of removal technology of contaminated particles in the scale of a few microns or even smaller. It is known that the surface cleaning technology using $CO_2$ snow has its own merits of high efficiency. However, the detailed removal mechanism of particles using this technology is not yet fully understood due to the lack of sophisticated research endeavors. The detachment mechanism of particles from the substrates is known to be belonged in four types; rebounding, sliding, rolling and lifting. In this study, a modeling effort is performed to explain the detachment mechanism of a contaminant particle due to the rebounding caused by the vertical collision of the $CO_2$ snow. The Hertz and Johnson-Kendall-Roberts(JKR) theories are employed to describe the contact, adhesion and deformation mechanisms of the particles on a substrate. Numerical simulations are followed for several representative cases, which provide the perspective views on the dynamic characteristics of the particles as functions of the material properties and the initial inter-particle collision velocity.

• Journal of Environmental Science International
• /
• v.12 no.9
• /
• pp.997-1004
• /
• 2003

The objective of this research was to test whether, under controlled laboratory conditions, hybrid SNCR/SCR process improves N $O_{x}$ removal efficiency in comparison with the SNCR only. The hybrid process is a combination of a redesigned existing SNCR with a new downstream SCR. N $O_{x}$ reduction experiments using a hybrid SNCR/SCR process have been conducted in simple NO/N $H_3$/ $O_2$ gas mixtures. Total gas flow rate was kept constant 4 liter/min throughout the SNCR and SCR reactors, where initial N $O_{x}$ concentration was 500 ppm in the presence of 5% or 15% $O_2$. Commercial catalysts, $V_2$ $O_{5}$ -W $O_3$-S $O_4$/Ti $O_2$, were used for SCR N $O_{x}$ reduction. The residence time and space velocity were around 1.67 seconds and 2,400 $h^{-1}$ or 6000 $h^{-1}$ in SNCR and SCR reactors, respectively. N $O_{x}$ reduction of the hybrid system was always higher than could be achieved by SNCR alone at a given value of N $H_{3SLIP}$. Optimization of the hybrid system performance requires maximizing N $O_{x}$ removal in the SNCR process. An analysis based on the hybrid system performance in this lab-scale work indicates that a equipment with N $O_{xi}$ =500 ppm will achieve a total N $O_{x}$ removal of about 90 percent with N $H_{3SLIP}$ $\leq$ 5 ppm only if the SNCR N $O_{x}$ reduction is at least 60 percent. A hybrid SNCR/SCR process has shown about 26∼37% more N $O_{x}$ reduction than a SNCR unit process in which a lower temperature of 85$0^{\circ}C$ turned out to be more effective.be more effective.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.4
• /
• pp.986-994
• /
• 2017

In this paper, $CO_2$ absorption of scrubber was tested for removal of high concentration $CO_2$. Liquid to gas ratio($18L/m^3$) and Superficial velocity(0.14 m/s) was determined through Lab-scale test. As flow rates increase 1, 2, 3, 4 and $5m^3/min$, $CO_2$ removal efficiency decrease 98.47%, 96.46%, 92.95%, 89.71% and 85.49%. Also, the scrubber operation made energy improvement(5.4%), energy saving(11.5 TOE/year) and greenhouse gases reduction(6.5 TC/year).

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.6
• /
• pp.17-23
• /
• 2011

In this study, a series of experiments were carried out to remove total petroleum hydrocarbon(TPH) and toluene by soil flushing. In batch experiments, Triton X-100 and SWA 1503 showed TPH removal efficiency of 79.0% and 69.0%, respectively. Although the TPH removal efficiency increased as the surfactant was increased in the concentration range 1-11mmol/L, the optimum concentration was 1mmol/L, considering the ratio of the removal efficiency to the amount of surfactant injected. In column experiment, the optimal velocity was 0.3mL/min. The physical aquifer model(PAM) result revealed that the soil flushing removed as much as 5.5% of the toluene under 3 pore volume(PV) conditions. To improve the soil flushing efficiency, it is necessary to find optimal condition through recirculation or reuse of surfactant.

• Journal of Conservation Science
• /
• v.34 no.2
• /
• pp.97-106
• /
• 2018

The lime-soil mixture on barrier (LSMB) tomb is a representative type of tomb from the Joseon Dynasty. It is an important reference for understanding the society and funeral culture of that time. The LSMB excavated at the Gungri site were classified with manufacturing type. The ultrasonic velocity and rebound hardness method were used to estimate the physical properties of the LSMB. The strength values on the tomb of layered wall were different depend on measuring method. The compressive strengths of the tomb with layered wall, which is calculated by ultrasonic velocity and rebound hardness ranged from 4.0 to 355 (mean 43.6) $kgf/cm^2$ and 18.8 to 538 (mean 245.2) $kgf/cm^2$ ranges. The damage to the tomb with integrated wall during excavation and removal of the corpse could be a reason for the difference in results obtained using ultrasonic velocity method. Compressive strengths of tombs with integrated wall, which is calculated by ultrasonic velocity and rebound hardness ranged from 5.7 to 793 (mean 281.6) $kgf/cm^2$ and 4.5 to 550.5 (mean 172.4) $kgf/cm^2$ values. Physical properties on the tombs of integrated wall had different in compressive strength value but showed similar tendency. Thus, evaluation of the physical properties has shown that measuring ultrasonic velocity and rebound hardness methods are more effective in the LSMB with integrated walls. Further, the strength values obtained through the rebound hardness method are more constant than those obtained through the ultrasonic method due to the small detection area required by the former.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.21 no.2
• /
• pp.63-70
• /
• 2013

Experiments in a pilot-scale hybrid multi-stage unit system (HMUS) combination of ATAD and EGSB followed by SBR process for pig slurry treatment were conducted to demonstrate the feasibility of using autothermal thermophilic aerobic digestion (ATAD) and expended granular sludge bed (EGSB) followed by sequencing batch reactor (SBR) system. Contaminants in pig slurry with high organic matter, nitrogen (N) and phosphorus (P) content were completely removed in the combined process. The highest removal rate for CODcr among contaminants in the feed pig slurry was attained by about 43.3% in ATAD unit process. Also TS removal rate of 96.5% was attained and the highest in the next coagulation unit process. The highest removal rate of CODcr under operating parameter conditions of OLR(organic loading rate), 3-6Kg $COD/m^3{\cdot}day$ and line velocity, 1.5-4m/h was earned at 3days of HRT. The disinfection of pathogens was effective at 50,000mg/L of TS in ATAD unit process. Biogas production per organic removal was $2.3{\sim}8.5m^3/kgTS{\cdot}d$ (average $5.2m^3/kgTS{\cdot}d$) in EGSB unit process. The average removal rates of CODcr 71.7%, TS 64.1%, TN 45.9%, and TP 50.4% were earned in the intermittent aeration SBR unit process.

• Clean Technology
• /
• v.29 no.4
• /
• pp.313-320
• /
• 2023

In order to increase the usability of H₂-SCR, the NOx removal characteristics with catalyst powder of PtNi/CeO₂-W-TiO₂ using Ce as a co-catalyst was synthesized and coated on a porous metal structure (PMS) were evaluated. Catalyst powder of PtNi/CeO₂-W-TiO₂(PtNi nanoparticles onto W-TiO₂, with the incorporation of ceria (CeO₂) as a co-catalysts) was synthesized and coated onto a porous metal structure (PMS) to produce a Selective Catalytic Reduction (SCR) catalyst. H₂-SCR with CeO₂ as a co-catalyst exhibited higher NOx removal efficiency compared to H₂-SCR without CeO₂. Particularly, at a 10wt% CeO₂ loading ratio, the NOx removal efficiency was highest at 90℃. As the amount of catalyst coating on PMS increased, the NOx removal efficiency was improved below 90℃, but it was decreased above 120℃. When the space velocity was changed from 4,000 h^-1 to 20,000 h^-1, the NOx removal efficiency improved at temperatures above 120℃. It was expected that the use of the catalyst could be reduced by applying the PMS with excellent specific surface area as a support.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.1
• /
• pp.1-12
• /
• 1990

The study is concerned with the analysis of combined forging of non-axisymmetric shapes with inclined protrusions by UBET technique. Work hardening is considered for the given range of strain rate during the forging process. A complex shape with inclined cavities is analyzed by subdividing the workpiece into finite UBET elements for which simple velocity fields are applicable. An experimental set-up was designed and manufactured for the experiment, and experiments are carried out with lead billets. The devised set-up can be used for closed-die forging of complex shapes with protrusions in which the dies can be separated automatically for easy removal of the forged products. Based on the derived kinematically admissible velocity fields for corresponding UBET elements, general computer programs have been developed. Since the energy dissipation rate for each elemental region is provided by subprograms (Subroutine or Function), the developed program can be applied to the forging problems of various shapes. The present study has shown that the method developed can be effectively applied to forging of non-axisymmetric shapes with complicated protrusions.