• 한국콘텐츠학회논문지
• /
• 제14권12호
• /
• pp.555-564
• /
• 2014

DIBR(Depth Image Based Rendering)을 이용한 영상 합성 시에 발생하는 경계 잡음은 원래 전경 영역에 속하던 화소가 배경으로 흩어져 나와 생성된 잡음이며, 이는 주로 참조 영상과 깊이지도 간 경계 불일치나 참조 영상에서의 블러링 때문에 발생된다. 영상 합성 과정에서 발생된 홀 영역은 일반적으로 주위 화소를 이용하여 채워지게 되므로, 홀에 인접한 경계 잡음은 합성 영상의 화질을 저하시키는 주요 원인으로 작용한다. 이 문제를 해결하기 위해 본 논문은 깊이지도의 전처리를 이용한 새로운 경계 잡음 제거 알고리즘을 제안한다. 기존의 전처리 기법들은 경계 불일치에 따른 경계 잡음의 제거를 위해 참조 영상과 깊이지도의 경계가 일치되도록 깊이지도를 수정한다. 그러나 대부분의 기존 기법들이 신호 기울기 기반의 단순 경계 탐색 알고리즘에 기반을 두고 있어 블러링이 존재하는 경계에서는 탐색 성능의 저하가 나타난다. 제안 알고리즘은 이의 해결을 위해 2단계 경계 탐색을 이용함으로써 이행 영역과 배경 영역 간 경계를 보다 효과적으로 탐색할 수 있는 구조를 제안하였다. 실험 결과를 통해 제안 알고리즘이 기존 알고리즘에 비해 우수한 경계 잡음 제거 성능을 가짐을 보인다.

• 상하수도학회지
• /
• 제19권1호
• /
• pp.16-24
• /
• 2005

Mathematical model was developed to verify a sequential particle removal taking place in a granular media gravity filter. Consequential multi-layer filtration cycle model was applied to verify the fraction of filter effluent particles that are filter influent particles that were never removed as well as the fraction of filter effluent particles that were detached after deposition were performed through laboratory experiments. Three sizes of marker particles were injected ahead of the filter column as a pulse in the presence of four sizes of polystyrene particles that were used as a primary source of particles in the raw suspension to investigate particle attachment alone in contrast to net removal from attachment and detachment. Microscopic counting of filter effluent particles was assumed to reflect attachment. Experimental results indicated that particle detachment is significant beginning from the early phase of filtration. For each size of fluorescent microspheres at one filter depth, fluorescent microsphere removal increased with filter runtime to a maximum due to ripening. The detached fraction of effluent particles increased with particle size and filter depth. The presence of detached particles and the increasing fraction of detached particles in deeper bed were confirmed.

• 한국안전학회지
• /
• 제5권1호
• /
• pp.31-39
• /
• 1990

In this paper, the influence of the table speed, metal removal rate and grinding fluid on long wheel workpiece contact zone at high effect grinding was investigated by theoretical analyses and measuring the temperature, and discussed by the temperature distribution in grinding surface layer. Main results obtained are as follows, 1) Rega.dless of the table speed, the temperature gap of the workpiece(heat influx) is about 6-8 times as high in dry condition as in wet condition. 2) Good grinding condition can be obtained owing to the effect of grinding fluid without any burning defect under the condition of the metal removal rate(1.0mm$^3$/mm.s) in case of wet grinding. 3) When the depth from the surface layer is about 1.25-1.5mm under the condition of the slow table speed, surface temperature goes up higher as the table speed slows down, because long contact time is laked at the surface layer. 4) In case of the same metal removal rate, the lower the table speed becomes, the higher the surface temperature is, because grinding depth has a far more influence on wheel workpiece contact zone than the table speed.

• 한국정밀공학회지
• /
• 제15권2호
• /
• pp.14-20
• /
• 1998

Automatic finishing process requires the development of high efficient and precision abrasive machining method for dies and molds. This study describes the evaluation of the finishing characteristics, such as surfrace roughness, topography and material removal depth of the electrolytic mixed abrasive machining methods. Experimental setup is composed of 3 axis machining center, a newly developed finishing attachment with constant pressure, electrode and electrolytic bath. Finally, we achieved a successful result that surface roughness is $0.01\mu$m Ra and material removal depth is $120\mu$m using electrolytic(0.8A. 30V) mixed abrasive (#400 CBN, #320 SiC) machining method.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.787-792
• /
• 2000

Ultra-abrasives such as diamond and CBN have used to maintain accuracy and form deviation for superalloy etc. This study contains the dry cylindrical grinding of metals with Vitrified-bond CBN wheel. For various conditions of grinding speed, workpiece speed, grinding depth and feed speed of table, the grinding resistance, the surface roughness, and the material removal are measured and discussed. The results are as follows.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.937-941
• /
• 1997

Utomatic finishing process requires the development of high efficient and precision abrasive machining method for die and molds. This study describes the evaluation of the finishing characteristics, such as sufrace roughness, topography and material removal depth, of the electrolytic chemical mixed abrasive machining method. Experimental setup is composed of 3 axis machining center, a newly developed finishing attachment with constant pressure, electrode and electrolytic bath. Finally, we achieved a successful result that surface roughness is 0.01 .mu. m Ra and material removal depth is 145 .mu. m after 100 times repeat-finishing using electrolytic (0.8A,30V) mixed abrasive (#400 CBN, #320 Sic) machining method.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.1053-1057
• /
• 1997

Laser thin film process with a Q-switch pulsed YAG laser was performed for micro machining. In this research, we performed basic Cr thin film on glass substrates removal machining experiments. Form experiments, it happens not only evaporration of thin film but also spatter and cohesion of melting substance in working region, when machining a Cr thin film by Q-switch YAG laser beam irradiation. Critical energy of surface irradiation type by irradiation direction of laser in a face composing thin film on the glass is higher than that of back irradiation type, but the latter is favorable because of spatter appearance. In case of image formation position when laser beam is irradiated, the defocus is permitted to a certain extent within forcus depth. Ifexceeds focus depth, formation of pattern is vanishing step by step.

• Journal of Periodontal and Implant Science
• /
• 제28권2호
• /
• pp.371-376
• /
• 1998

This study presents an evaluation of the effectiveness of nonsurgical subgingival scaling and root planing related to initial pocket depth, type of teeth, and individual root surfaces. A total of 110 teeth designated for periodontal surgery in 67 patients with marginal periodontitis were selected and received thorough scaling and root planing with standard rigid Gracey curettes. After a healing period of 4 to 8 weeks, residual calculus was assessed at the time of periodontal surgery following the reflection of mucoperiosteal flap. The results demonstrated a high correlation between the percentage of residual calculus and initial pocket depth. It was further noted that tooth type and involved root surface also influenced the rate of calculus remnant. The results of this study suggest that complete removal of subgingival calculus utilizing conventional instrumentation via closed approach is rare.

• 대한치과보철학회지
• /
• 제29권1호
• /
• pp.281-287
• /
• 1991

This study was designed to investigate the influence of the clasp arm length on the change of retentive force with repeated placement or removal. The author measured the retentive force of Akers clasp and I-bar clasp in the depth of undercut 0.5mm, 0.25mm, respectively, varying the length of clasp arm, that is, 10mm, 14mm, 17mm in Akers clasp and 16mm, 18mm, 20mm in I-bar clasp. The retentive force was measured just before the placement of removal, after 100 times repeated placement or removal, after 300 times repeated placement or removal. The obtained results were as follows : 1. The shorter the clasp arm, the greater retention in Akers clasp and I-bar clasp(p<0.05). 2. There was decreased retentive force of Akers clasp and I-bar clasp after 300 times repeated placement or removal(p.<0.005). 3. The decreasing rate of retentive force in Akers clasp with 10mm was higher than that with 17mm, after 300 times repeated placement or removal, but there was no statistica difference(p>0.05).

• 한국토양비료학회지
• /
• 제48권5호
• /
• pp.326-331
• /
• 2015

High salinity and sodicity of soils play a negative role in producing crops in reclaimed tidal lands. To evaluate the effects of soil ameliorants on salt removal in a highly saline and sodic soil of reclaimed tidal land, we conducted a column experiment with treating gypsum, compost, and phosphate at 0-2 cm depth and measured the salt concentration of leachate and soil. Electrical conductivity of leachate was $45-48dSm^{-1}$ at 1 pore volume (PV) of water and decreased to less than $3dSm^{-1}$ at 3 PV of water. Gypsum significantly decreased SAR (sodium adsorption ratio) of leachate below 3 at 3 PV of water and soil ESP (exchangeable sodium percentage) below 3% for the whole profile of soil column. Compost significantly decreased ESP of soil at 0-5 cm depth to 5% compared with the control (20%). However, compost affected little the composition of cations below a depth of 5 cm and in leachate compared with control treatment. It was concluded that gypsum was effective in ameliorating reclaimed tidal lands at and below a soil layer receiving gypsum while compost worked only at a soil layer where compost was treated.