• Journal of the Korea Concrete Institute
• /
• v.23 no.1
• /
• pp.109-120
• /
• 2011

This paper presents an experimental study results on the crack control of flexure-dominant reinforced concrete beams repaired with strain-hardening cement composite (SHCC). Five RC beams were fabricated and tested until failure. One unrepaired RC beam was a control specimen (CBN) and remaining four speciemens were repaired with SHCC materials. The test parameters included two types of SHCC matrix ductility and two types of repair method (patching and layering). Test results demonstrated that RC beams repaired with SHCC showed no concrete crushing or spalling until final failure, but numerous hair cracks were observed. The control specimen CBN failed due to crushing. It is important to note that SHCC matrix can improve crack-damage mitigation and flexural behavior of RC beams such as flexural strength, post peak ductility, and energy dissipation capacity. In the perspective of crack width, crack widths in RC beams repaired with SHCC had far smaller crack width than the control specimen CBN under the same deflection. Especially, the specimens repaired with SHCC of PVA0.75%+PE0.75% showed a high durability and ductility. The crack width indicates the residual capacity of the beam since SHCC matrix can delay residual capacity degradation of the RC beams.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.23 no.1
• /
• pp.81-94
• /
• 2010

This paper deals with the fracture simulation of UHPFRC girder with the interface type model. Based on the existing numerical simulation of quasi-brittle fracture in normal strength concrete, constitutive modeling for UHPFRC I-girder has been improved by including a tensile hardening at the failure surface. The finite element formulation is based on a triangular unit, constructed from constant strain triangles, with nodes along its sides and neither at the vertex nor the center of the unit. Fracture is simulated through a hardening/softening fracture constitutive law in tension, a softening fracture constitutive law in shear as well as in compression at the boundary nodes, with the material within the triangular unit remaining linear elastic. LCP is used to formulate the path-dependent hardening-softening behavior in non-holonomic rate form and a mathematical programming algorithm is employed to solve the LCP. The piece-wise linear inelastic yielding-failure/failure surface is modeled with two compressive caps, two Mohr-Coulomb failure surfaces, a tensile yielding surface and a tensile failure surface. The comparison between test results and numerical results indicates this method effectively simulates the deformation and failure of specimen.

• The Journal of Korean Academy of Prosthodontics
• /
• v.37 no.2
• /
• pp.143-166
• /
• 1999

The success of porcelain laminate veneer depends on the bond strength between tooth structure and ceramic restoration and the design of tooth preparation. In particular, incisal coverage and incisal finish line are the two most important factors in long-term fracture resistance. Although the majority of clinicians are practicing incisal coverage and there are various opinions on the geo-metrical ratio between the clinical crown length of the remaining tooth structure and the length of incisal extension in porcelain laminate veneer and the optimal incisal finish lines. scientific evidence still loaves much to be desired. The purpose of this study was to determine the effects of the amounts of incisal coverage and the types of incisal finish line on the stress distribution in maxillary anterior porcelain laminate veneers under two different loading conditions. Three-dimensional finite element models of a maxillary anterior porcelain veneer with differ-ent amounts of incisal coverage ; 0, 1, 2, and 3mm and different incisal finish lines feathered edge, incisal bevel, reverse bevel and lingual chamfer with various amounts of lingual extension were developed. 300N force was applied at the point 0.5mm cervical of the linguoincisal edge in two loading conditions ; A) 125 degrees, B) 132 degrees. Tensile and compressive stress in ceramic and shear stress in the resin cement layer were analyzed using three-dimensional finite element method. The results were as follows : 1. The types of incisal finish line had more influence on the stress distribution in porcelain laminate veneer than the amounts of incisal coverage. 2. In case of no incisal coverage, incisal beveled laminate exhibited more evenly distributed tensile stress than feathered edged laminate. And in case of incisal coverage, reverse beveled laminate and lingual chamfered laminate with 1mm lingual extension exhibited more evenly distributed tensile stress than lingual chamfered laminates with 2mm and 3mm lingual extension. 3. As long as the lingual chamfer goes, less tensile stress was found at the incisal edge, while much more tensile stress was found at the lingual margin area in proportion to the length of lingual extension. 4. Under 125 degree load, tensile stress in porcelain laminate veneer had increased compared with that under 132 degree load and the difference exhibited by the change of the amount of tooth support was larger. 5. The types of incisal finish line and the distance from the incisal finish line to the loading point had more influence on the shear stress distribution in the resin cement layer than the amounts of incisal coverage. In contrast loading condition had little influence.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.16 no.1
• /
• pp.125-133
• /
• 2010

Researches and studies which have been conducted so far on external confinement of long span concrete columns have mainly concentrated on concentric loading. But, long span bridge concrete columns over the sea are mainly subjected to concentrated axial load, and at the same time lange amount of moment by eccentric load. This paper experimentally investigates the performance of externally confined high-strength concrete columns subjected to loading mechanism and evaluates the effectiveness of two confinement materials carbon fibre and high performance glass fibre. Twelve short columns with the same dimensions were cast and tested Six columns were reinforced with hoop bars, the remaining six columns were reinforced with spiral bars and wrapped with three layers of carbon failure and high performance glass FRP sheets. Test variables considered were the shape of internal reinforcement and strengthening materials according to loading location. The experimental results showed that eccentric load could obviously lower down the maximum failure load of FRP-confined concrete columns, compared with the columns under concentric load. And compared with the carbon FRP-confined reinforced concrete columns, high performance glass FRP-confined columns displayed a higher load capacity and ductility, when tested both concentrically and eccentrically.

• Economic and Environmental Geology
• /
• v.52 no.1
• /
• pp.91-106
• /
• 2019

The Donghachong tomb from Royal Tombs at Neungsanri is composed of 15 sides including the floor, and the most highly proportion of rock, two-mica granite, are used on the 7 sides (46.6%). Also, augen gneiss consist with another 3 sides (20.0%), and each of the remaining 3 sides (6.7%) are made up of granodiorite, gneissous granite and leucocratic granite, all of which were used to comprise the tabural stone. Meanwhile, the two floors of the burial chamber and the front chamber, are made up of brick-shaped amphibole schist (13.3%). These rocks are occurred in the Buyeo area and their provenance sites are located at the side of Guemgang river. The Memorial Stone for Liu Renyuen in Tang China is a typical augen gneiss showing distinct schistosity and augen texture. This rock has the same petrographic characteristics with the rocks used to build the Donghachong tomb, Sanjikri dolmens and Setapri pagoda in Buyeo. This augen gneiss is distributed from the Jeungsanri in Buyeo to Dukjiri in Gongju as a large scaled rock body, and where currently are the quarries to produce stone aggregates, garden and landscape rocks. Thus, it is highly probable that the site around Buyeo was the source area of augen gneisses since the Bronze Age. However, while augen gneiss is easier to form into shapes it should have disadvantages when it comes to painting on the tomb wall because of their petrographic characteristics of low strength and dark color. Therefore, it is very intriguing to investigate which transportation method the people of Baekje chose with consideration of the distance and terrain, efficiency and convenience.

• Structural Engineering and Mechanics
• /
• v.70 no.1
• /
• pp.67-80
• /
• 2019

Strengthening with near surface mounted carbon fibre reinforced polymers (NSM-CFRP) is a strengthening technique that have been used for several decades to increase the load carrying capacity of reinforced concrete members. In Iraq, many concrete buildings and bridges were subjected to a wide range of damage as a result of the last war and many other events. Accordingly, there is a progressive increase in the strengthening of concrete structures, bridges in particular, by using CFRP strengthening techniques. Near-surface mounted carbon fibre polymer has been recently proved as a powerful strengthening technique in which the CFRP strips are sufficiently protected against external environmental conditions especially the high-temperature rates in Iraq. However, this technique has not been examined yet under repeated loading conditions such as traffic loads on bridge girders. The main objective of this research was to investigate the effectiveness of NSM-CFRP strips in reinforced concrete beams under repeated loads. Different parameters such as the number of strips, groove size, and two types of bonding materials (epoxy resin and cement-based adhesive) were considered. Fifteen NSM-CFRP strengthened beams were tested under concentrated monotonic and repeated loadings. Three beams were non-strengthened as reference specimens while the remaining were strengthened with NSM-CFRP strips and divided into three groups. Each group comprises two beams tested under monotonic loads and used as control for those tested under repeated loads in the same group. The experimental results are discussed in terms of load-deflection behavior up to failure, ductility factor, cumulative energy absorption, number of cycles to failure, and the mode of failure. The test results proved that strengthening with NSM-CFRP strips increased both the flexural strength and stiffness of the tested beams. An increase in load carrying capacity was obtained in a range of (1.47 to 4.49) times that for the non-strengthened specimens. Also, the increase in total area of CFRPs showed a slight increase in flexural capacity of (1.02) times the value of the control strengthened one tested under repeated loading. Increasing the total area of CFRP strips resulted in a reduction in ductility factor reached to (0.71) while the cumulative energy absorption increased by (1.22) times the values of the strengthened reference specimens tested under repeated loading. Moreover, the replacement of epoxy resin with cement-based adhesive as a bonding material exhibited higher ductility than specimen with epoxy resin tested under monotonic and repeated loading.

• Journal of Oral Medicine and Pain
• /
• v.48 no.3
• /
• pp.87-95
• /
• 2023

Purpose: To quantify the relationship between perceived pain intensity and psychological variables in a sample of participants with temporomandibular disorder, with or without central sensitization (CS). Methods: A cross-sectional study with nonprobability convenience sampling was conducted from January 1, 2022, to June 30, 2023. Pain intensity (Numeric Pain Rating Scale), anxiety (State-Trait Anxiety Questionnaire, STAI), catastrophizing (Pain Catastrophizing Scale, PCS), perceived stress (Perceived Stress Scale, PSS), and sleep quality (Pittsburgh Sleep Quality Index, PSQI) were assessed. Statistical analysis was performed using IBM SPSS Statistics for Windows, Version 20.0 (IBM Co.), which included descriptive and normality analyses and the calculation of strength of multiple correlational regression. Results: A total of 52 (n=34 female 65.4%; n=18 male 34.6%) subjects with diagnosis of temporomandibular disorders (TMD) were finally included. A total of 26 participants (n=26, 50.0%) were cases suffered from CS (TMD-CS mean=46.62±11.24) while the remaining participants (n=26, 50.0%) were the controls (TMD-nCS mean=26.77, standard deviation [SD]=8.42). The pain intensity was moderate in both groups TMDCS (mean=7.62, SD=0.83) and TMD-nCS (mean=7.05, SD=0.86), anxiety (TMD-CS STAI mean=53.27, SD=11.54; TMD-nCS STAI mean=49, SD=11.55), catastrophizing (TMD-CS PCS mean=46.27, SD=9.75; TMD-nCS PCS mean=26.69, SD=4.97), perceived stress (TMDCS PSS mean=30.35, SD=4.91; TMD-nCS PSS mean=26.12, SD=6.60) and sleep quality (TMD-CS PSQI mean=15.81, SD=3.65; TMD-nCS PSQI mean=12.77, SD=2.76) levels were measured in both groups. In TMD-CS and TMD-nCS, higher anxiety levels were moderately and significantly associated with greater pain intensity β=0.4467 (t=2.477, p=0.021) and β=0.5087 (t=2.672, p=0.014). Nevertheless, catastrophizing, perceived stress and sleep quality were not associated to pain intensity in neither of group. Conclusions: In both TMD-CS and TMD-nCS patients, elevated anxiety levels were moderately and significantly associated with increased pain intensity. However, heightened levels of pain catastrophizing, perceived stress, and poor sleep quality were not significantly associated with increased pain intensity in either of the two analyzed groups.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.26 no.3
• /
• pp.223-242
• /
• 2024

Single-shell tunnels, introduced to South Korea in the early 2000s, have not been adopted for the main tunnels of roads or railways over the past two decades despite several attempts starting with the Gwangju City Bypass. This reluctance likely arises from concerns about the long-term performance of supporting materials and the absence of relevant criteria and specifications. However, recent progress, including the incorporation of high-strength shotcrete standards and corrosion-resistant rock bolt specifications, alongside equipment and technique enhancements, necessitates a reassessment of single-shell tunnels. While the single-shell tunnel method offers advantages in environmental impact, construction cost and period compared to the conventional NATM, it is crucial to address the challenges, such as limited design and construction experience, incomplete detailed standards, and insufficient construction specifications, through further research and pilot projects. This paper reviewed the basic principles of single-shell tunnel, current application and research status, technical development trends, criteria and specifications, and remaining challenges. It aims to reignite discussions on the feasibility of applying single-shell tunnels in South Korea.

• Journal of Animal Science and Technology
• /
• v.52 no.5
• /
• pp.389-398
• /
• 2010

The objective of this study was to investigate the effects of three strains of Bacillus subtilis (B. subtilis) supplemented to diets on egg production, egg quality, egg yolk cholesterol levels, the profile of cecal microflora, and tibia characteristics in laying hens. One hundred sixty 76-week-old Hy-Line Brown layers were randomly divided into 4 groups with 4 replicates per group (10 birds per replicate). Birds in the control group were fed a corn-soybean meal based diet. The remaining three treated groups were fed the control diet containing either 0.05% B. subtilis Ch3 (T1), 0.05% B. subtilis Ch3 + B. subtilis W1 (T2) or 0.05% B. subtilis commercial product (T3) for 6 weeks, respectively. There were no differences in feed intake, egg weight, egg production and egg mass among the groups. The dietary supplementation of B. subtilis improved eggshell strength and Haugh units compared to those of control (P<0.05). The activities of GOT and GPT in serum were not also affected by the dietary treatments. The population of total microbes and lactic acid bacteria in cecum were significantly increased by the dietary B. subtilis (P<0.05), but not the coliforms. The cholesterol concentration in egg yolk and serum in the treated groups were significantly decreased compared to those of control (P<0.05). Also, The levels of phospholipids in serum were significantly decreased compared to those of control (P<0.05). The supplementation of three strains of B. subtilis to diets significantly increased the contents of tibia ash compared to that of control (P<0.05). Thus, this study showed significant improvements in egg quality, such as eggshell strength and Haugh unit, by dietary B. subtilis strains. The B. subtilis strains added to the diets modulated the profiles of cecal microflora, reflecting beneficial effects in laying hens.

• Korean Journal of Heritage: History & Science
• /
• v.55 no.2
• /
• pp.200-211
• /
• 2022

The celadon stools with an openwork ring design which consist of four items as one collection were excavated from Gaeseong, Gyeonggi-do Province. The celadon stools were designated and managed as treasures due to their high arthistorical value in the form of demonstrating the excellence of celadon manufacturing techniques and the fanciful lifestyles during the Goryeo Dynasty. However, one of the items, which appeared to have been repaired and restored in the past, suffered a decline in aesthetic value due to the aging of the treatment materials and the lack of skill on the part of the conservator, raising the need for re-treatment as a result of structural instability. An examination of the conservation condition prior to conservation treatment found structural vulnerabilities because physical damage had been artificially inflicted throughout the area that was rendered defective at the time of manufacturing. The bonded surfaces for the cracked areas and detached fragments did not fit, and these areas and fragments had deteriorated because the adhesive trickled down onto the celadon surface or secondary contaminants, such as dust, were on the adhesive surface. The study identified the position, scope, and conditions of the bonded areas at the cracks UV rays and microscopy in order to investigate the condition of repair and restoration. By conducting Fourier-transform infrared spectroscopy(FT-IR) and portable x-ray fluorescence spectroscopy on the materials used for the former conservation treatment, the study confirmed the use of cellulose resins and epoxy resins as adhesives. Furthermore, the analysis revealed the addition of gypsum(CaSO₄·2H₂O) and bone meal(Ca₁₀ (PO₄)₆(OH)₂) to the adhesive to increase the bonding strength of some of the bonded areas that sustained force. Based on the results of the investigation, the conservation treatment for the artifact would focus on completely dismantling the existing bonded areas and then consolidating vulnerable areas through bonding and restoration. After removing and dismantling the prior adhesive used, the celadon stool was separated into 6 large fragments including the top and bottom, the curved legs, and some of the ring design. After dismantling, the remaining adhesive and contaminants were chemically and physically removed, and a steam cleaner was used to clean the fractured surfaces to increase the bonding efficacy of the re-bonding. The bonding of the artifact involved applying the adhesive differently depending on the bonding area and size. The cyanoacrylate resin Loctite 401 was used on the bonding area that held the positions of the fragments, while the acrylic resin Paraloid B-72 20%(in xylene) was treated on cross sections for reversibility in the areas that provided structural stability before bonding the fragments using the epoxy resin Epo-tek 301-2. For areas that would sustain force, as in the top and bottom, kaolin was added to Epo-tek 301-2 in order to reinforce the bonding strength. For the missing parts of the ring design where a continuous pattern could be assumed, a frame was made using SN-sheets, and the ring design was then modeled and restored by connecting the damaged cross section with Wood epos. Other restoration areas that occurred during bonding were treated by being filled with Wood epos for aesthetic and structural stabilization. Restored and filled areas were color-matched to avoid the feeling of disharmony from differences of texture in case of exhibitions in the future. The investigation and treatment process involving a variety of scientific technology was systematically documented so as to be utilized as basic data for the conservation and maintenance.