• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.9
• /
• pp.1632-1642
• /
• 1992

When a blind hole of small diameter is drilled in the field of residual stress, strain relieved around the hole is function of magnitude of stress, patterns of stress distribution and hole geometry of diameter and depth. Relieved strain coefficients can be calculated from FEM analysis of relieved strain and actual stress. These relieved strain coefficients make it possible to measure residual stress which vary along the depth in the subsurface of stressed material. In this study, the calibration tests of residual stress measurement are carried out by drilling a hole incrementally on the cantilever or on the tensile test bar. Residual stresses can be determined from measured strains around a shallow hole by application of power series method. For the sake of reliable measurement of residual stress, much efforts should be done to measure relieved strains and hole depth more accurately comparing with conventional procedures of gage subject to the external load. Otherwise linear equations converting strains into stresses may yield erratic residual stresses because of ill-conditions of linear equations. With accurate measurements of relieved strains, residual stress even if varying along the depth can be measured. It is also possible to measure residual stress in the thin film of material by drilling a shallow hole.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.2
• /
• pp.268-277
• /
• 1998

The numerical procedure for calculating non-uniform residual stress fields by using relieved strain data from incremental hole drilling method is presented. Finite element calculations are described to evaluate the relieved coefficients required for the determination of residual stresses. From the results of simulations it is found that this numerical method is well adopted to measuring non-uniform residual stress in the hole depth range of 0.8 times of the hole diameter from the surface. In order to examine the practicability of this method, the hole drilling procedure for the four point bending test is performed. This method is applied to the measurement of residual stresses in the cold-rolled steel pipe. It is shown that the magnitude of residual stress in the pipe is not negligible when compared with yield stress and the residual stress should be duly considered in designing structures with this pipes.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.11 s.242
• /
• pp.1542-1550
• /
• 2005

This paper presents the numerical procedure for calculating non-uniform residual stresses based on relieved displacements obtained from incremental hole drilling. The relationship between the in-plane displacement produced by introducing a blind hole and the corresponding residual stress is established. Finite element calculations are described to evaluate the relieved coefficients required for the determination of non-uniform residual stresses. Validity of the proposed method has been tested through three axisymmetric test examples and two three-dimensional examples. As a result of . simulation on the test examples, it is found that this numerical procedure is well adopted to measuring non-uniform residual stress in the full hole depth range of the hole diameter from the surface. The accuracy of the hole drilling method with displacement measurement is discussed, comparing tile method with strain measurement

• Proceedings of the Korean Biophysical Society Conference
• /
• 2001.06a
• /
• pp.31-31
• /
• 2001

The native strain of serpins (serine protease inhibitors) has been recognized as a mechanism of biological regulation. Indeed, some stabilizing single residue mutations of human $\alpha$$_1$-antitrypsin, a prototype serpin, relieved local strain and caused the loss of inhibitory activity. The native strain of $\alpha$$_1$-antitrypsin is distributed throughout the whole molecule, but the strain that regulates the function directly is highly localized in the regions that appear to be mobilized during complex formation with a target protease.(omitted)

• Journal of Welding and Joining
• /
• v.22 no.2
• /
• pp.33-37
• /
• 2004

Since the preflex beam is fabricated by welding, the pre-compressive stresses that should occur over the concrete pier are diminished by the welding residual stresses. For this reason distribution of welding residual stresses must be analyzed accurately and welding residual stresses should be relieved during the fabrication. In this study strain history, displacement of beam and re-distributed welding residual stresses by different loading conditions are measured and compared to choose more appropriate preflex condition.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.1
• /
• pp.238-246
• /
• 1998

Surface residual stresses as well as wall thickness and ovality changes after U-bending process on UNS N06690 row-1 heat exchanger tubes, were estimated. Surface residual stresses were measured by Hole Drilling Method(HDM), calculating the stresses from relieved strains of 3 rosette strain gages. After bending of the tubes, dimensional tolerances for wall thickness and ovality were satisfied with ASTM requirements. Residual stresses at the extrados were introduced with compressive stress(-) by bending operations, and its maximum value reached-319 MPa in axial direction at ${\phi}=0^{\circ}$ in position. Tensile residual stresses(+) of ${\sigma}_zz=45$ MPa,${\sigma}_zz=25$ MPa were introduced in the intrados surface at position of ${\phi}=0^{\circ}$ Maximum tensile residual stress of 170 MPa was detected on the flank side at position of ,${\phi}=95^{\circ}$i.e., at apex region. It appeared that higher stress gradients were generated at the irregular transition regions. In the trend of residual stress changes with U-bend position, the extrados is related with the changes of ovality and the intrados is related with the changes of wall thickness.

• Composites Research
• /
• v.22 no.3
• /
• pp.29-34
• /
• 2009

In this paper, finite element analyses were used to estimate the strain distribution at the fracture site of a tibia bone. A stainless steel bone plate and various composite bone plates were considered to find out the best conditions for callus generation while bone fracture was cured for 16 weeks. Through this research, the appropriate load condition which makes the strains between the appropriate range($2{\sim}10%$) was sought. From this analysis, it was found that lower level of external load is needed for the appropriate strain for the case of composite bone plate application and it was also found that the composite bone plate had potential advantages for effective bone fracture healing relieved stress shielding effect.

• Journal of Microbiology and Biotechnology
• /
• v.23 no.11
• /
• pp.1577-1585
• /
• 2013

Bioethanol production from lignocellulose is considered as a sustainable biofuel supply. However, the low cellulose hydrolysis efficiency limits the cellulosic ethanol production. The cellulase is strongly inhibited by the major end product cellobiose, which can be relieved by the addition of ${\beta}$-glucosidase. In this study, three ${\beta}$-glucosidases from different organisms were respectively expressed in Saccharomyces cerevisiae and the ${\beta}$-glucosidase from Saccharomycopsis fibuligera showed the best activity (5.2 U/ml). The recombinant strain with S. fibuligera ${\beta}$-glucosidase could metabolize cellobiose with a specific growth rate similar to the control strain in glucose. This recombinant strain showed higher hydrolysis efficiency in the cellulose simultaneous saccharification and fermentation, when using the Trichoderma reesei cellulase, which is short of the ${\beta}$-glucosidase activity. The final ethanol concentration was 110% (using Avicel) and 89% (using acid-pretreated corncob) higher than the control strain. These results demonstrated the effect of ${\beta}$-glucosidase secretion in the recombinant S. cerevisiae for enhancing cellulosic ethanol conversion.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.170-170
• /
• 2003

We have implanted on sapphire substrate with various ions and investigated the properties of GaN epilayers grown on implanted sapphire substrate by metal organic chemical vapor deposition (MOCVD). Sapphire is typical substrate for GaN epilayers. However, there are many problems such as lattice mismatch and thermal coefficient difference between sapphire substrate and GaN. The ion implanted substrate's surface had decreased internal tree energies during the growth of the GaN epilayer, md the misfit strain was relieved through the formation of an AlN phase on the ions implanted sapphire(0001) substrates. [1] The crystal and optical properties of GaN epilayer grown in ions implanted sapphire(0001) substrate were improved.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.201-206
• /
• 2001

The hole-drilling method makes a little hole through the metal surface that has residual stress and measures the relieved stress with a strain gage. It is used widely in measuring the residual stress of surfaces. In this method, the inclined hole is one of the source of error. This paper presents a finite element analysis of influence of the inclined hole for the uniaxial residual stress field. The stress differences between measured and applied residual stress increase proportionally to inclined angle of the hole. The correction equations which easily obtain the residual stress taking account of the inclined angle and direction are derived. The measurement error of stress due to the inclined hole can be reduced to around 1% through this study.