• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.7
• /
• pp.97-103
• /
• 2004

In this paper, we propose a high speed block turbo code decoding algorithm and an efficient hardware architecture. The multimedia wireless data communication systems need channel codes which have the high-performance error correcting capabilities. Block turbo codes support variable code rates and packet sizes, and show a high performance due to a soft decision iteration decoding of turbo codes. However, block turbo codes have a long decoding time because of the iteration decoding and a complicated extrinsic information operation. The proposed algorithm using the threshold that represents a channel information reduces the long decoding time. After the threshold is decided by a simulation result, the proposed algorithm eliminates the calculation for the bits which have a good channel information and assigns a high reliability value to the bits. The threshold is decided by the absolute mean and the standard deviation of a LLR(Log Likelihood Ratio) in consideration that the LLR distribution is a gaussian one. Also, the proposed algorithm assigns '1', the highest reliable value, to those bits. The hardware design result using verilog HDL reduces a decoding time about 30% in comparison with conventional algorithm, and includes about 20K logic gate and 32Kbit memory sizes.

• Journal of Periodontal and Implant Science
• /
• v.37 no.1
• /
• pp.103-113
• /
• 2007

The purpose of this study was to measure the thickness of masticatory mucosa in the hard palate as a donor site for mucogingival surgery by using computerized tomography(CT), Thickness measurements were performed in 84 adult patients who took CT on maxilla for implant surgery and 24 standard measurement points were defined in the hard palate according to the gingival margin and mid palatal suture. Radiographic measurements were utilized after calibration for standardization. Data were analyzed to determine the differences in mucosal thickness by gender, age, tooth positions and depth of palatal vault. The results of this study were as follows: 1. Mean thickness of palatal masticatory mucosa was $3.93{\pm}0.6mm$ and females had significantly thinner mean masticatory mucosa($3.76{\pm}0.56mm$) than males($4.04{\pm}0.6mm$)(p<0.05). 2. The thickness of palatal masticatory mucosa increased by aging. 3. Depending on position, masticatory mucosa thickness increased from canine to premeolar, but decreased at the first molar, and increased again in the second molar region(p<0.0001). 4. No significant difference in mean thickness of palatal masticatory mucosa were indentified between low palatal vault group and high palatal vault group(p>0.05). The results suggest that canine and premolar area appears to be the most appropriate donor site for soft tissue grafting procedure. The measurement of the thickness of palatal masticatory mucosa by using computerized tomography can offer useful information clinically but further studies in as-sessing the validity and reliability of the method using computerized tomography is needed.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.3B
• /
• pp.277-284
• /
• 2011

The limitations of existing Markov chain model for reproducing extreme rainfalls are a known problem, and the problems have increased the uncertainties in establishing water resources plans. Especially, it is very difficult to secure reliability of water resources structures because the design rainfall through the existing Markov chain model are significantly underestimated. In this regard, aims of this study were to develop a new daily rainfall simulation model which is able to reproduce both mean and high order moments such as variance and skewness using a piecewise Kernel-Pareto distribution. The proposed methods were applied to summer and fall season rainfall at three stations in Han river watershed in Korea. The proposed Kernel-Pareto distribution based Markov chain model has been shown to perform well at reproducing most of statistics such as mean, standard deviation and skewness while the existing Gamma distribution based Markov chain model generally fails to reproduce high order moments. It was also confirmed that the proposed model can more effectively reproduce low order moments such as mean and median as well as underlying distribution of daily rainfall series by modeling extreme rainfall separately.

• Fire Science and Engineering
• /
• v.34 no.1
• /
• pp.11-17
• /
• 2020

As performance-based design (PBD) has a direct impact on evacuation safety assessments, designing fire scenarios based on real fire tests is essential. To improve the reliability of the PBD for fire safety in multiplexes, information on fire behavior, such as heat release rate (HRR) and fire spread rate, are provided in this study by conducting a standard fabric flammability test. To this end, several chairs were arranged in a pattern that resembled a theater-style seating. The peak HRR and heating value per unit mass for each chair ranged from 415 kW to 988 kW and 15.2 MJ/kg to 23.8 MJ/kg, respectively. The heating values per unit mass of the new and old chairs were 23.6 MJ/kg and 16.7 MJ/kg, respectively. As the quantity of plastic and cushioning materials in the new chairs was more than that of the old ones, the new chairs were more vulnerable to fire hazards. Furthermore, when the chairs were arranged in a line, the fire spread rate was observed to be 0.39-0.42 m/min, regardless of the ignition location. Finally, a fire growth curve showing the peak HRR and fire spread rate was also demonstrated.

• Journal of Digital Convergence
• /
• v.15 no.8
• /
• pp.161-168
• /
• 2017

The purpose of this study is to investigate the effect of restaurant selection factors on reliability and revisit intention. The results of empirical analysis were as follows: First, the factors influencing the intention to visit the restaurant were the physical environment, service, price, location, reputation, cleanliness, It is confirmed that consumers are willing to visit again if their satisfaction is high because they choose general consumers considering kindness and taste. Second, trust is found to affect re - visit intention and it can be judged that store faith is actively considering return visit through consumer 's belief. Third, it was found that the factor of selecting the restaurant business influenced the intention to visit again according to the trust. When the customer chooses according to the restaurant business standard and satisfies the trust, it intends to increase the intention to visit again. The results of this study are as follows. First, it is found that the factors of restaurant selection and trust affect the revisit intention of restaurants, and it is meaningful to provide theoretical and strategic implications.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.22 no.3
• /
• pp.191-201
• /
• 2010

The breakwaters are designed by considering the cost optimization because a human risk is seldom considered. Most breakwaters, however, were constructed without considering the cost optimization. In this study, the optimum return period, target failure probability and the partial safety factors were evaluated by applying the cost optimization to the rubble mound breakwaters in Korea. The applied method was developed by Hans F. Burcharth and John D. Sorensen in relation to the PIANC Working Group 47. The optimum return period was determined as 50 years in many cases and was found as 100 years in the case of high real interest rate. Target failure probability was suggested by using the probabilities of failure corresponding to the optimum return period and those of reliability analysis of existing structures. The final target failure probability is about 60% for the initial limit state of the national design standard and then the overall safety factor is calculated as 1.09. It is required that the nominal diameter and weight of armor are respectively 9% and 30% larger than those of the existing design method. Moreover, partial safety factors considering the cost optimization were compared with those calculated by Level 2 analysis and a fairly good agreement was found between the two methods especially the failure probability less than 40%.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.14 no.1
• /
• pp.40-45
• /
• 2010

Purpose: Recently, the performance of the X-ray tube was very much improved by the power generation of the technology. However, the overload of equipment is occurred by the increment of the equipment operating time according to the increment of the examination number of cases. The X-ray dose can change by heat occurrence of the X-ray tube due to this. Moreover, the change of the bone mineral density value is possible to occur. Therefore, We tries to whether the change of the bone mineral density value of each equipment according to the difference of the examination number of cases and operating time occur or not. Materials and Methods: The BMD value was measured by the Aluminum Spine Phantom and the European Spine Phantom in each equipment, in order to find out about the difference of the time general classification bone mineral density value by using the Dual energy X-ray absorptiometry. And after scanning each phantom by using X-ray dose meter (Unfors Mult-O-Meter), a dose was measured by the same condition. As to, an average and standard deviation were found and the change of each equipment much BMD value was compared and it evaluated. Results: $Mean{\pm}SD$ of each equipment by using the Aluminum Spine Phantom, A equipment was $1.174{\pm}0.002$, $1.171{\pm}0.005$, $1.173{\pm}0.005$, B equipment was $1.186{\pm}0.003$, $1.187{\pm}0.003$, $1.185{\pm}0.003$, C equipment was $1.180{\pm}0.003$, $1.182{\pm}0.004$, $1.183{\pm}0.002$, D equipment was $1.188{\pm}0.004$, $1.185{\pm}0.003$, $1.185{\pm}0.004$. By using the European Spine Phantom, A equipment was $1.143{\pm}0.006$, $1.153{\pm}0.009$, $1.161{\pm}0.003$, B equipment was $1.134{\pm}0.004$, $1.13{\pm}0.008$, $1.127{\pm}0.015$, C equipment was $1.143{\pm}0.006$, $1.134{\pm}0.01$, $1.133{\pm}0.006$, D equipment was $1.14{\pm}0.001$, $1.122{\pm}0.002$, $1.131{\pm}0.008$, altogether included in the normal range. Conclusion: There was no significant change of the BMD value of using a phantom by time zones. Therefore, if the quality control is made to use the extent management method of the equipment for beginning in the present application, the reliability of the BMD equipment will be able to be enhanced.

• Phonetics and Speech Sciences
• /
• v.11 no.4
• /
• pp.97-108
• /
• 2019

An automated Praat script was implemented to measure optimal formant frequencies for adults. Optimal formant analysis could be interpreted to show that the deviation of formant frequency that resulted from the two variously combined setting parameters (maximum formant and number of formants) was minimal. To increase the reliability of formant analysis, LPC order should be set differently, based on the gender or vowel type. Praat recommends 5,000 Hz and 5,500 Hz as maximum formant settings and, at the same time, recommends 5 as the number of formants for males and females. However, verification is needed to determine whether these recommended settings are valid for Korean vowels. Statistical analysis showed that formant frequencies significantly varied across the adapted scripts, especially with respect to the data on females. Formant plots and statistical results showed that linear_script and qtone_script are much more reliable in formant measurements. Among four kinds of scripts, the linear and qtone_scripts proved to be more stable and reliable. While the linear_script was designed to have a linearly increased formant step in for-loop, the increment of formant step in the qtone_script was arranged by quarter tone scale (base frequency×common ratio ($\sqrt[24]{2}$)). When looking at the tendency of the formant setting drawn by the two referred algorithms in the context of front vowel [i, e], the maximum formant was set higher; and the number of formants set at a lower value than recommended by Praat. The back vowel [o, u], on the contrary, has a lower maximum formant and a higher number of formants than the standard setting.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.4
• /
• pp.77-86
• /
• 2008

The reliability of leaded and lead-free solders of BGA type packages on a printed circuit board was investigated by employing the standard drop test and 4-point bending test. Tested solder joints were examined by optical microscopy to identify associated failure mode. Three-dimensional finite element analysis(FEM) with ANSYS Workbench v.11 was carried out to understand the mechanical behavior of solder joints under the influence of bending or drop impact. The results of numerical analysis are in good agreement with those obtained by experiments. Packages in the center of the PCB experienced higher stress than those in the perimeter of the PCB. The solder joints located in the outermost comer of the package suffered from higher stress than those located in center region. In both drop and bending impact tests, the lead-free solder showed better performances than the leaded solders. The numerical analysis results indicated that stress and strain behavior of solder joint were dependent on various effective parameters.

• Korean Journal of Childcare and Education
• /
• v.9 no.4
• /
• pp.55-74
• /
• 2013

This study examined the influence of ego-resilience and psychological well-being on job stress in childcare teachers. The participants were 192 childcare teachers in Seoul and Daejeon Metropolitan City. The research instruments were Ego-Resilience by Park(1996), Psychological well-being by Kim(2008), and Job Stress by Hong(2009). Collected data were analysed by descriptive statistics(frequency analysis, mean, & standard deviation) and multiple regression, and Cronbach's ${\alpha}$ for reliability by SPSS PC program. The results were as follows: First, Childcare teachers' perceived ego-resilience was higher than average. Childcare teachers' perceived psychological well-being was higher than average. Childcare teachers' perceived job stress was lower than average. Second, Childcare teachers' perceived ego-resilience and psychological well-being was having significant influences on childcare teachers' perceived job stress. Optimistic thinking and anger control among sub-factors of childcare teachers' perceived ego-resilience and environmental mastery among sub-factors of childcare teachers' perceived psychological well-being explained 46% of variance in childcare teachers' perceived job stress. These results provide informations for reducing job stress in childcare teacher and suggest the basis of an education program for childcare teacher.