• Journal of the Korean GEO-environmental Society
• /
• v.15 no.2
• /
• pp.5-15
• /
• 2014

Target reliability index in the limit state design indicated the safety margin and it is important to determine the partial factor. To determine the target reliability index which is needed in the limit state design, the six design and construction case histories of gravel compaction piles (GCP) were investigated. The limit state functions were defined by bulging failure for the major failure mode of GCP. The reliability analysis were performed using the first order reliability method (FORM) and the reliability index was calculated for each ultimate bearing capacity formulation. The reliability index of GCP tended to be penportional to the safety factor of allowable stress design and average value was ${\beta}$=2.30. Reliability level that was assessed by reliability analysis and target reliability index for existing structure foundations were compared and analyzed. As a result, The GCP was required a relatively low level of safety compared with deep and shallow foundations and the currd t reliability level were similar to the target reliability in the reinforced earth retaining-wall and soil-nailing. Therefore the target reliability index of GCP suggested as ${\beta}_T$=2.33 by various literatures together with the computed reliability level in this study.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.3
• /
• pp.249-259
• /
• 2020

Design criteria for limit state design of underground structures have already been published overseas, and research has been conducted to revise the design method in Korea. In order to estimate the probability of failure under seismic load, the probability variable should be considered in the reliability analysis. In this study, the failure probability of the existing shield tunnel segment lining design was calculated by applying the coefficient of variation (COV) for the earth pressure and the seismic load effect in consideration of the statistical characteristics of the domestic ground properties. Based on the results of calculating the reliability index (β) from the calculated probability of failure and analyzing the reliability index according to the change in the load factor and the results of domestic and foreign research, the target reliability index (β_T) during earthquakes of shield tunnel segment lining is analyzed to be "2.3", it was proposed as the target reliability index for the design of the limit state under seismic load.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.23 no.6
• /
• pp.422-428
• /
• 2011

Optimal reliability indices were found by optimizing life cycle cost(LCC) of pier type quay walls. Failure probability of pier and shore bridge were calculated by response surface method. Then, they were used to obtain recovery cost after damage. Costs for initial construction and maintenance were also considered in finding optimal reliability indices. Target reliability indices which may be used in reliability based design were suggested by numerical examples under seismic load and ship load.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.21 no.4
• /
• pp.278-289
• /
• 2009

In the present study, we evaluated the target reliability indices and partial safety factors for caisson sliding of a vertical breakwater. The average of the reliability indices of existing breakwaters was proposed as the target reliability index for the breakwater of normal safety level. The target reliability indices of high and low safety levels were also proposed based on the analysis of breakwaters in Korea and Japan. The partial safety factors were then proposed for each safety level by averaging the values calculated for 12 breakwater crosssections in Korea. The appropriateness of the proposed partial safety factors was partly verified by showing that the reliability index calculated by using the present partial safety factors is located between those of mild and steep bottom slopes of JPHA(2007). The proposed partial safety factors were inversely used to calculate the caisson width and reliability index of existing breakwaters. While the reliability indices of existing breakwaters designed by the deterministic method show a large variation, those designed by the partial safety factor method show a small variation. This indicates that the partial safety factor method allows a consistent design for given target probability of failure.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.39 no.1
• /
• pp.13-24
• /
• 2019

This paper brings up fallacy of material factors specified for the design of concrete members in the current Korean limit state design code for highway bridges, and proposes new material factors based on a robust optimization scheme to overcome the fallacy. It is shown that the current load factors in the code and the proposed material factors lead to a much higher reliability index than the target index. The load factors are adjusted to yield the target reliability index using the inverse reliability analysis. A reliability-based approach following the basic concept of Eurocode is formulated to determine material factors as well as load factors. The load-material factors obtained by the proposed reliability-based approach yield a lower reliability level than the target index. Drawbacks of the basic concept of Eurocode are discussed. It is pointed out that differences in the uncertainties between materials and members may cause the lower reliability index of concrete member than the target.

• Geotechnical Engineering
• /
• v.4 no.2
• /
• pp.15-24
• /
• 1988

To identify the stability of cantilever retaining wall in safe state by the deterministic method, these potential modes of such geotechnical failures as bearing capacity, horizontal sliding and overturning are analysed using Advanced First Order Second Moment (AFOSM) method. All design variables are assumed of the normal distribution and to be statistically independent. Considering the correlations between the single modes, structural system reliability index is 2. 05. Even if the safety factors are larger than the required value in the codes' by the conventional deterministic method, the system reliability of this structure may not be Judged to be safe state since the system reliability index is much lower than general value of 3.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.21 no.3
• /
• pp.224-229
• /
• 2009

Partial safety factors(PSFs) for Level I reliability based design of caisson type quay walls were calculated. First order reliability method(FORM) based PSFs are the functions of sensitivities of limit state function with respect to design random variables, target reliability index, characteristic values and first moment of random variables. Modified PSFs for water level and resilient water level are newly defined to keep consistency with the current design code. In the numerical example, PSFs were calculated by using a target reliability index. Seismic coefficient is defined to show extreme distribution. It was found that PSFs for seismic coefficient becomes smaller as the return period for design seismic coefficient grows longer.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.6
• /
• pp.643-651
• /
• 2014

In this paper the reliability analyses of the cable-supported bridge design code which is recently issued in Korea are performed and the results are presented. Governing load combinations for the member design and the statistical properties of the main members are introduced and the analysis is performed using an example cable-stayed bridge for which the design is performed following the load and resistance factors defined in the design code. The reliability analysis shows the target reliability index can be achieved by applying load and resistance factors and the application of the resistance modification factor can enhance the reliability level if the importance of the bridge needs to be increased. The sensitivity analysis reveals that decreasing uncertainty of the cable strength is critical for obtaining the target reliability index. The study results show that the design using the load and resistance factors of the code can achieve the target reliability indexes for the design of cable supported bridge.

• Journal of dental hygiene science
• /
• v.15 no.3
• /
• pp.377-382
• /
• 2015

The purpose of this study was to evaluate the validity and reliability of plaque scoring system using new Qraycam (All in One Bio, Korea) device which enables plaque score without tooth disclosing. This study measured Quigley-Hein index and plaque control record by both Qraycam and disclosing agent on 64 elderly people and checked degree of congruence between the two methods. Reliability was evaluated with the mean of measured values, kappa index and intraclass correlation coefficient statistical analysis. The analysis of the plaque scores showed a high agreement between the measured values according to the method of measurement and the measured part. The mean of plaque index of anterior labial were not significantly different according to measurement method. The kappa index was higher by Qraycam and tooth disclosing method of plaque index. Therefore, it was verified that Qraycam has sufficient reliability as screening tool for plaque scoring system.

• Journal of Korea Technology Innovation Society
• /
• v.15 no.1
• /
• pp.105-128
• /
• 2012

This paper proposes the technological level assessment which improved reliability and the efficient noise elimination methods in the process of establishing patent map analysis data. In order to eliminate efficiently noise (removed by the manual process in the past), the paper applies the Logical Operator 'AND', makes it a program in excel VBA(Visual Basic Application), and obtains the valid data. For the improved reliability technological level assessment of the patents, the study calculates average number of claims, Patent Family Size(PFS), Cites Per Patent (CPP), Triad Patent Families, Standardization Patent Diversification Index (stdPCPI), and haF-index(Hirsch a Family index). The result which applied noise exclusion work showed less than 10% of acquired patent data ratio and confirmed high reliability. The result that apply proposed technological level assessment index makes sure that balanced technological level assessment which improved reliability by producing synthetic technological level assessment.