• Journal of Microbiology and Biotechnology
• /
• v.17 no.3
• /
• pp.524-529
• /
• 2007

Pressure inactivation behavior of Bacillus amyloliquefaciens spores was investigated in deionized water. The spores of B. amyloliquefaciens were subjected to $105^{\circ}C$ and 700 MPa. The magnitude of the decrease in viability after pressure treatment was similar to that after pressure treatment followed by heat shock. The increase of dipicolinic acid (DPA) release was correlated with the spore inactivation, and the hydrophobicity did not significantly change during the pressure-assisted thermal processing (PATP). Lag phase duration increased with increasing pressure process time. The mechanisms of spore germination and inactivation during the PATP were related to a complex physiological process.

• Journal of Power System Engineering
• /
• v.2 no.2
• /
• pp.20-26
• /
• 1998

Heat release data were obtained by analysis of cylinder diagrams from a test engine, naturally-aspirated small-size four-stroke DI diesel engine. These data were used to decide empirical coefficients of Whitehouse-Way's model, single zone combustion model. Finally, the comparison of calculated with experimental results was performed, and the accuracy of calculated versus experimental data of the model in predicting engine heat release and cylinder pressure was demonstrated.

• Journal of the Korean Society of Combustion
• /
• v.17 no.1
• /
• pp.30-36
• /
• 2012

Dynamic characteristics of combustion occurring in various combustion devices have been extensively studied since most of high-performance combustion devices are susceptible to hazardous, unstable combustion that deteriorates combustor's lifetime. One of the most severe unstable combustion phenomena is high-frequency combustion instability in which heat release fluctuations from combustion are coupled to resonant modes of the combustor. Here in this study, characteristics of high-frequency combustion instabilities observed in three different combustion devices have been presented. Lean-premixed combustion instability occurs mainly due to equivalence ratio fluctuations which induce large heat release oscillations at lean conditions. Liquid-fueled combustion also shows high-frequency instability from energy coupling between pressure and heat release oscillations.

• The Korean Journal of Physiology
• /
• v.28 no.2
• /
• pp.225-231
• /
• 1994

The present study was undertaken to investigate the role of endogenous nitric oxide in renin release under different physiological conditions. In the first series of experiments, renin release was either inhibited by acute volume-expansion (VE) or stimulated by clipping one renal artery in the rat. VE was induced by intravenous infusion of saline (0.9% NaCl) up to 5% of the body weight over 45 min under thiopental (50 mg/kg, IP) anesthesia. VE caused a decrease of plasma renin concentration (PRC). With $N^G-nitro-L-arginine$ methyl ester $(L-NAME,\;5\;{\mu}g/kg\;per\;min)$ superadded to VE, PRC decreased further. The magnitude of increase in plasma atrial natriuretic peptide levels following VE was not affected by the L-NAME. In two-kidney, one clip rats, L-NAME-supplementation resulted in a decrease, and L-arginine-supplementation an increase of PRC. Plasma atrial natriuretic peptide levels were significantly lower in the L-arginine group than in the control. Blood pressure did not differ among the L-NAME, L-arginine, and control groups. In another series of experiments, the renin response to a blockade of NO synthesis was examined using in vitro preparations from isolated renal cortex. L-NAME significantly increased basal renin release, although it was without effect on the isoproterenol-stimulated release. These findings suggest that endogenous nitric oxide significantly contributes to the renin release. Since many factors may affect the renin release in vivo, an interaction between NO and renin under various pathophysiological states is to be further defined.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.5
• /
• pp.572-579
• /
• 2006

Accurate heat release analysis based on the cylinder pressure trace is important for evaluating combustion process of diesel engines. However, traditional single-zone heat release models (SZM) have significant limitations due mainly to their simplified assumptions of uniform charge and homogeneity while neglecting local temperature distribution inside cylinder during combustion process. In this study, a heat release analysis based on single-zone model has been evaluated by comparison with computational simulation result using Fire-code, which is based on multidimensional model (MDM). The limitations of the single-zone assumption have been estimated, To overcome these limitations, an improved model that includes the effects of spatial non-uniformity has been applied. From this improved single-zone heat release model (Improved-SZM), two effective values of specific heat ratios, denoted by ${\gamma}_V$ and ${\gamma}_H$ in this study, have been introduced. These values are formulated as the function of charge temperature changing rate and overall equivalence ratio. Also, it is applied that each equation of ${\gamma}_V$ and ${\gamma}_H$ has respectively different slopes according to several meaningful periods during combustion progress. The heat release analysis results based on improved single-zone model gives a good agreement with FIRE-code results over the whole range of operating conditions of target engine, Hyundai HiMSEN H21/32.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.240-243
• /
• 2003

Combustion instability phenomena have been observed in various different combustion systems. For each specific combustion system, pressure fluctuations measured during high frequency combustion instability presented many different characteristics. High frequency instability occurring in a lean premixed gas turbine combustor mar be dominantly affected by a nonlinear relation between pressure oscillations and heat release rate fluctuations, and gas dynamics plays a crucial role in determining an amplitude of a limit cycle for a liquid rocket thrust chamber. Combustion instability phenomena manifest their inherent nonlinear characteristics. One is a limit cycle and the other bifurcation described by nonlinear time series analysis.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3264-3269
• /
• 2007

Combustion instability is a serious obstacle for the lean premixed combustion of gas turbines, and can even cause fatal damage to the combustor and the entire system. Thus, improved understanding of the mechanisms of combustion instability is necessary for designing and operating gas turbine combustors. In this study, in order to understand the instability phenomena, an experimental study was conducted in a rearwardstep dump combustor with LPG and air. The fluctuations of pressure and heat release were measured by piezoelectric pressure sensor and High speed Intensified Charge Coupled Device (ICCD) camera respectively. Various types of combustion modes occurred in accordance with the equivalence ratio and the fuel supplying conditions. The unmixedness of the fuel and air can be controlled by changing the mixing distance ($L_{fuel}$). It is found that the unmixedness of the fuel and air affects the characteristics of flame behavior and pressure fluctuations in a lean premixed flame.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.28 no.2
• /
• pp.184-190
• /
• 1992

The combustion characteristics, ignition delay, p-t, dp/dt, Q-t of diesel oil and fish oil blended diesel oils was investigated according to pressure and temperature in a constant volume combustion bomb. The results are as follows: 1) The influence of temperature and pressure on the ignition delay was almost constant in high temperature, regardless of the blending rates, and the ignition delay was shortest in the 60% blend. 2) The maximum pressure was high in order of with pure diesel oil, with the 20% blend and the 60% blend. 3) The rate of pressure rise was high in order of with pure diesel oil, with the 20% blend and the 60% blend. The rate of maximum pressure rise was significantly higher with pure diesel oil than with two blends. 4) The amount of accumulative heat release was large in order of with pure diesel oil, with the 20% blend and the 60% blend.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.320-325
• /
• 2003

Acoustic-Pressure Response of diluted hydrogen-air diffusion flames is investigated numerically by adopting a fully unsteady analysis of flame structures. In the low-pressure regime, the amplification index remains low and constant at low frequencies. As acoustic frequency increases, finite-rate chemistry is enhanced through a nonlinear accumulation of heat release rate, leading to a high amplification index. Finally, the flame responses decrease at high frequency due to the response lag of the transport zone. For a medium-pressure operation and low-frequency excitation, the amplification index is low and constant. It then decreases at moderate frequencies. As frequency increases further, the amplification index increases appreciably due to an intense accumulation effect.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.5
• /
• pp.53-59
• /
• 2001

A screw driver is widely used in assembling machine parts or electronic products such as the printed circuit board with a housing. As the parts to be assembled becomes small and precise, the higher precision of the controlling screw driver torque is required. However, because the operator controls the fastening torque based on experience, it must be inexact and the setting procedure will be time consuming job. Thus the screw driver which can exactly control the fastening torque is developed utilizing a bellows in this paper. The bellows is expanded by the inner air pressure and contracted by the spring operation. The bellows type driver is composed of a clutch mechanism with two solenoid valves and a pressure sensor. Those valves are controlled using the detected bellows pressure by the sensor. When the pressure reaches the setting value, the exit solenoid valve is opened to release the air pressure from the bellows so as not to deliver further torque. Through a series of experiments, the performance is examined and verified.