• 오토저널
• /
• 제3권1호
• /
• pp.1-4
• /
• 1981

Clutch disc 의 facing은 사용할 때마다 마찰로 인하여 마멸된다. 마멸함에 따라 clutch cover의 구조상 clutch cover의 release lever가 올라와 clutch release bearing (thrust bearing)과의 간 극이 작아져서 드디어 이 간극이 없어지게 되면 release lever가 clutch release bearing을 누르게 되어 평상에도 clutch가 절반 정도로 떨어지는 상태로까지 됨으로써 clutch의 완전한 연결을 할 수 없어 slip이 일어나게 된다. 이상과 같은 문제점들을 해소하기 위하여 clutch의 control system을 수시로 조정하지 않으면 안되며 이러한 번거로움을 피하기 위하여 release lever가 올라옴으로써 release bearing과의 간극이 작아져서 자동적으로 일정한 간극을 유지하여 clutch의 slip을 방지하고 clutch기구의 내구성을 향상시키기 위한 것이 무조정식 release cylinder, 혹은 clutch adjuster이다. 이에 대한 신형식 두 종류의 구조, 작동 및 특징에 대하여 해설하여 본다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권7호
• /
• pp.1063-1071
• /
• 2004

Accurate heat release analysis of cylinder pressure data is important for evaluating performance in the development of diesel engine However, traditional single zone first law heat release model(SZM) has significant limitations due to the simplified assumption of uniform charge and neglecting local temperature inside cylinder during combustion process. In this study. heat release rate based on single zone heat release model has been evaluated by comparison with computational analysis results using Fire code which is based on multi-dimensional model(MDM). To overcome limitations due to simplicity of single zone assumption. especially the influence of specific heat ratio on gross heat release has been esteemed and newly suggested were the equation $\gamma$= $\gamma$(${T/T}_{max}$) which describes the variations of gases thermodynamic properties with mean temperature and maximum mean temperature inside cylinder Single zone heat release model applied with this equation is shown to give very good results over whole range of operating conditions when compared with computational analysis results based on multi-dimensional model.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권7호
• /
• pp.1101-1110
• /
• 2004

An one-zone heat release analysis was applied to a 4 cylinder indirect injection diesel engine. The objective of the study is to calculate heat release accurately considering the effect of specific heat ratio. heat transfer and crevice model and to find out combustion characteristics of an indirect diesel engine considering the effect of the pressures in main and swirl chambers. Especially specific heat ratio indicating combustion characteristics is adapted. instead of that indicating matter properties, which has been used in former studies Moreover by adaption of blowby model, cylinder gas mass became accurately calculated. Therefore, with ideal gas equation, calculating cylinder gas temperature, it was found to affect heat transfer loss and heat release. Determining heat transfer constants $C_1$. $C_2$ as 0.6 respectively. the integrated gross heat release values were predicted well for the measured value at various engine speed, full load operating conditions. The curve of heat release rate was similar to SI engine rather than DI engine. That is originated from that swirl chamber reduce an instant combustion which occurs in DI engine due to ignition delay on early stage of combustion.

• International Journal of Automotive Technology
• /
• 제4권3호
• /
• pp.125-133
• /
• 2003

Several models for the evaluation of Gross Heat Release from the internel combustion engine (ICE) are often used in literature. One of these is the First Law - Single Zone Model (FL-SZM), derived from the First Law of Thermodynamic. This model present a twice advantage: first it describes with accuracy the physic of the phenomenon (charge heat release during the combustion stroke and heat exchange between gas and cylinder wall); second it hat a great simplicity in the mathematical formulation. The evaluation of Heat Release with the FL-SZM is based on pressure experimental measurements inside the cylinder, and ell the assumption of several parameters as the specific heat ratio, wall temperature, polytropic exponent for the motored cycle evaluation, and many others. In this paper the influence of gases thermodynamic properties on Cross Heat Release has been esteemed. In particular the influence of an appropriate equation for k=k(T) (specific heat ratio vs. temperature) which describes the variations of gases thermodynamic properties with the mean temperature inside the cylinder has been evaluated. This equation has been calculated by new V order Logarithmic Polynomials (VoLP), fitting experimental gases properties through the least square methods.

• 한국추진공학회지
• /
• 제22권1호
• /
• pp.80-88
• /
• 2018

한국형 발사체 지상고정 장치는 발사체 이륙시 엔진 최대 추력에서 고정을 해제 한다. 고정력을 일시에 제거하면 추진체가 탱크 내부에서 상하로 진동하는 Ka Doing a Doing a Doing Mode를 유발할 수 있으므로, 점진적으로 고정력을 제거하는 기능이 필요하다. 본 연구에서는 이를 만족하기 위해 축압기 및 파이로 밸브로 유압구동기를 작동하고 구동기내 오리피스로 속도를 제어하는 지상고정장치 유압시스템의 작동 시험을 수행하였다. 주요 설계변수 변화 의한 유압구동기 운동속도의 영향을 분석하여 이를 바탕으로 구동기 요구속도를 만족시킬 수 있는 유압구동기 설계값들을 도출하였다. 이를 통하여 최대추력에서 동작할 수 있는 발사체 지상고정 장치의 개발을 위한 공학적 기반을 마련하였다.

• 한국자동차공학회논문집
• /
• 제16권5호
• /
• pp.164-170
• /
• 2008

A typical clutch system for automotive manual transmissions transfers hydraulic pressure generated by driver's pedal manipulation to the clutch diaphragm spring. The foot effort history during the period of push is different than the period of the clutch pedal's return. The effort or load difference is called clutch foot effort hysteresis. It is known that the hysteresis is caused by friction. The frictional force and moment are produced between various component contact points such as between the rubber seal and the inner wall inside the hydraulic cylinder and between the diaphragm spring and the pressure plate, etc. Understanding the clutch pedal foot effort hysteresis is essential for a clutch release system design and analysis. The dynamic model for a clutch release system is developed for the foot effort hysteresis prediction and a simulation analysis is performed to propose a tool for analysing a clutch system.

• 오토저널
• /
• 제7권3호
• /
• pp.74-82
• /
• 1985

Using single-zone heat release model and quasi-steady model, computer program for calculating the compression ignition engine cycle was composed. The properties in the cylinder were calculated in terms of crank angle and the effects of various operating conditions on rate of heat release and on engine performance were studied. The predicted values for the engine under consideration have shown good agreement with published data.

• 한국자동차공학회논문집
• /
• 제4권1호
• /
• pp.147-154
• /
• 1996

An one-zone heat release analysis was studied for a 6 cylinder direct injetction compressionignition engine. The heat transfer constants in this anlysis were calibrated to match the measured fuel energy at 1,000 rpm full load, which was the fuel mass multiplied by the fuel's heating value. The integrated gross heat release values were close to the measured fuel energy at various full load operating conditions. The combustion inefficiency from this calculation was proportional to the smoke of exhaust gas.

• 동력기계공학회지
• /
• 제11권1호
• /
• pp.51-55
• /
• 2007

A study on combustion characteristics using emulsified fuel in a diesel engine were performed experimentally. In this paper, the experiments were performed at engine speed 1800rpm, emulsion ratios were 0%, 10%, 20%, and main measured items were specific fuel consumption, cylinder pressure, rate of pressure rise, rate of heat release etc. The obtained conclusions were as follows. 1) Specific fuel consumption increased maximum by 19.8% at low load, but was not affected at full load. 2) Rate of pressure rise and rate of heat release were about the same in the case of 10% and 20% of emulsion ratio. 3) Cylinder Pressure increased 9.6%, rate of pressure rise increased 53.4% in case of emulsion ratio 20% at full load. 4) Rate of heat release increased 72.4% in case of emulsion ratio 20% at full load.

• 한국자동차공학회논문집
• /
• 제12권6호
• /
• pp.46-53
• /
• 2004

Heat release analysis is a very important method for understanding the combustion phenomena inside an engine cylinder. In this study, one-zone heat release analysis was used with the measured cylinder pressures of a HSDI(high speed direct injection) and IDI(indirect injection) diesel engines, Those have benefits of simple equation, fast speed, reliability. The objective of the study is to compare the combustion characteristics between a HSDI and an IDI. The result shoes that the maximum heat release rate of a HSDI is higher than that of an IDI because of long ignition delay period. The heat release curve of an IDI is more linear than that of a HSDI, thus is similiar to that of a SI engine. The combustion efficiency of a HSDI is higher than that of an IDI because of the smaller heat transfer loss of a HSDI. There is a suggestion here that an IDI engine has broad heat transfer area which include two combustion chambers, the connection passage of combustion chambers, etc.