• The KIPS Transactions:PartD
• /
• v.11D no.4
• /
• pp.951-958
• /
• 2004

This paper describes problems when visited ISP subscriber gets dynamic IP address in home ISP for wireless internet service on GPRS network. We propose a specific DHCP relay for wireless internet service of visited ISP subscriber on GPRS network. We designed and implemented the specific DHCP relay and installed it in ISP testbed. We show the allocated dynamic IP address using specific DHCP relay for visited ISP subscriber on GPRS network. Now we think it is possible the visited ISP subscriber can access wireless internet service on GPRS network using specific DHCP relay, and UMTS system can be managed IP address for subscriber roaming.

• Journal of Industrial Technology
• /
• v.21 no.A
• /
• pp.117-122
• /
• 2001

Currently, the VHE (suggested for global roaming user to provide personal service environment) implementation scenario is being proposed to realize 3G network requirements. However, developing VHE scenarios are focused on signal flow between node and network, and network and network. this case may result in weakness to protect subscriber's privacy in 3G network which commonly uses visited network. In this paper, we reanalyze a several VHE implementation scenarios for user profile protection, indicate a problem concerning user privacy, and finally, design a procedure to cope with vulnerability in VHE implementation scenario.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.11
• /
• pp.2113-2119
• /
• 2006

In this paper, we design the r-Sensor protocol for reliable data transmission in the Intelligent Home Service based on the wireless sensor network environment. The r-Sensor protocol improve the reliability of data transmission and node fairness using simple routing algorithm, congestion control, and loss recovery method that minimize the load of relay node. Reposed routing algorithm find out upstream and downstream nodes using the Network Management packet. Meanwhile, loss recovery algorithm uses the Aggregated-Nack. To apply supposed algorithm, the IHS-AMR(Intelligent Home Service - Automatic Meter Reader) and sensor node are designed and implemented in hardware. The IHS-AMR provides remote metering service and also offers home safety service by internetworking with sensor network, mobile phone network and internet.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.12
• /
• pp.2267-2273
• /
• 2016

In this paper, WiMedia Distributed-MAC protocol is adopted for development of an OSMU (One Source Multi Use) N-screen wireless multicast service. But, when considering wireless communication environment where channel error rate is time-variant, N-screen high-speed data is vulnerable to be lost. For this problem, a multicast relay scheme is proposed by analyzing Distributed-MAC protocol. In proposed multicast relay scheme, Multicast-free DRP Availability IE is combined and the relay node suitable for N-screen multicast transmissions is selected. Through this operation, it can avoid wireless channel with high errors and can transmit N-screen high-speed data. In simulation results, the proposed multicast relay scheme is compared with conventional Distributed-MAC multicast scheme in view points of throughput and energy consumption according to various numbers of multicast nodes and BER (Bit Error Rate) values in wireless channel. Through simulation results, it is explained that proposed multicast relay scheme should be adopted in WiMedia Distributed-MAC protocol to realize OSMU N-screen wireless multicast services.

• Journal of Communications and Networks
• /
• v.14 no.6
• /
• pp.640-652
• /
• 2012

Many studies have investigated the smart grid architecture and communication models in the past few years. However, the communication model and architecture for a smart grid still remain unclear. Today's electric power distribution is very complex and maladapted because of the lack of efficient and cost-effective energy generation, distribution, and consumption management systems. A wireless smart grid communication system can play an important role in achieving these goals. In this paper, we describe a smart grid communication architecture in which we merge customers and distributors into a single domain. In the proposed architecture, all the home area networks, neighborhood area networks, and local electrical equipment form a local wireless mesh network (LWMN). Each device or meter can act as a source, router, or relay. The data generated in any node (device/meter) reaches the data collector via other nodes. The data collector transmits this data via the access point of a wide area network (WAN). Finally, data is transferred to the service provider or to the control center of the smart grid. We propose a wireless cooperative communication model for the LWMN.We deploy a limited number of smart relays to improve the performance of the network. A novel relay selection mechanism is also proposed to reduce the relay selection overhead. Simulation results show that our cooperative smart grid (coopSG) communication model improves the end-to-end packet delivery latency, throughput, and energy efficiency over both the Wang et al. and Niyato et al. models.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.8
• /
• pp.688-695
• /
• 2014

In a small wireless environment, such as your home or office, a various network using WiMedia PHY can be mixed. Because these networks operate independently for each application, data conflict can occur between adjacent networks. To avoid data conflict, the resource in a different time zone can be utilized. However, if devices in a network increase, available resources in the network decrease, and then the lack of resources necessary to provide service can occur. To solve this problem, we propose collision avoidacne scheme for coexistence of various UWB systems. In this paper, we evaluate the performance of the proposed scheme through simulation.

• The KIPS Transactions:PartD
• /
• v.11D no.2
• /
• pp.443-452
• /
• 2004

The paper presents an intelligent space management system for ubiquitous computing. The system is basically a home/office automation system that could control light, electronic key, and home appliances such as TV and audio. On top of these basic capabilities, there are four elegant features in the system. First, we can access the system using either a cellular Phone or using a browser on the PC connected to the Internet, so that we control the system at any time and any place. Second, to provide more human-oriented interface, we integrate voice recognition functionalities into the system. Third, the system supports not only reactive services but also proactive services, based on the regularities of user behavior. Finally, by exploiting embedded technologies, the system could be run on the hardware that has less-processing power and storage. We have implemented the system on the embedded board consisting of StrongARM CPU with 205MHz, 32MB SDRAM, 16MB NOR-type flash memory, and Relay box. Under these hardware platforms, software components such as embedded Linux, HTK voice recognition tools, GoAhead Web Server, and GPIO driver are cooperated to support user-friendly intelligent space.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.11
• /
• pp.51-55
• /
• 2007

Generally, PLC (Power Line Communication) based home automation devices such as wall switch, walt socket, gas controller, etc, must maintain wake-up status at all time to control other electronic devices and monitor their on/off status whether they are in service or not. In order to reduce the unnecessary energy consumption during the standby mode, the new power-saving PLC 2 ports wall switch has been developed, separating PLC communication part and controller part and introducing sleep mode. In addition, to expand life cycle of PLC product and to reduce the rate of product failure in active mode, the instant controlling method in controlling process is adopted instead of the maintenance controlling method. In comparison to the earlier model, the new 2 ports PLC wall switch has reduced power by 0.95[W] less in standby mode and 3.2[W] less in active mode than the previous one.