• 한국분무공학회지
• /
• 제7권3호
• /
• pp.38-44
• /
• 2002

The purpose of this study is to investigate the effect of the volume fraction of water and injection pressure on the spray characteristics of water/oil emulsified fuel injected from the pressure swirl atomizer. The mixture of light oil and water by using impeller mixer was performed. The spray characteristics such as SMD and velocity were measured using PDPA. The injection pressures were 7.5, 100, 200 and $300kgt/cm^2$ and volume fractions of water in emulsified fuel were 0, 10, 20 and 30%, respectively. The measurement sections were at 30, 60 and 90mm from injection nozzle tip. SMD and velocity of emulsified fuel were larger gradually by increasing the volume fraction of water in emulsified fuel. The spray angle was decreased and axial velocity was increased with increase in water content. It was found that the relative SMD ratio was increased more greatly than the relative axial velocity ratio in super critical pressure. The relative SMD ratio was increased and the relative axial velocity ratio was decreased with increase injection pressure at spray downstream.

• Earthquakes and Structures
• /
• 제4권5호
• /
• pp.489-508
• /
• 2013

Design spectra for damping ratios higher than 5% have several important applications in the design of earthquake-resistant structures. These highly damped spectra are usually derived from a 5%-damped reference pseudo-acceleration spectrum by using a damping modification factor. In cases of high damping, the absolute acceleration and the relative velocity spectra instead of the pseudo-acceleration and the pseudo-velocity spectra should be used. This paper elaborates on the recovery of spectral absolute acceleration and spectral relative velocity from their pseudo-spectral counterparts. This is accomplished with the aid of correction factors obtained through extensive parametric studies, which come out to be functions of period and damping ratio.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.478-481
• /
• 2009

As a first step for aerodynamic analysis of vertical axis wind turbine, dynamic stall characteristics of airfoil was investigated. Dynamic stall of wind turbine airfoil is caused by severe variation of angle of attack and relative velocity of flow around airfoil. Angle of attack and relative velocity can be expressed with tip speed ratio. Variation of angle of attack is strongly dependent on the tip speed ratio. For tip speed ratio, 1.4 and free stream velocity, 15m/s, dynamic stall characteristics of wind turbine airfoil is compared with those of oscillating airfoil having same angle of attack variation.

• Smart Structures and Systems
• /
• 제17권1호
• /
• pp.73-89
• /
• 2016

The stress dependence of ultrasonic wave velocity is known as the acoustoelastic effect. This effect is useful for stress monitoring if the acoustoelastic coefficient of a subject medium is known. The acoustoelastic coefficients of metallic materials such as steel have been studied widely. However, the acoustoelastic coefficient of concrete has not been well understood yet. Basic constituents of concrete are water, cement, and aggregates. The mix proportion of those constituents greatly affects many mechanical and physical properties of concrete and so does the acoustoelastic coefficient of concrete. In this study, influence of the water-cement ratio (w/c ratio) and the fine-coarse aggregates ratio (fa/ta ratio) on the acoustoelastic coefficient of concrete was investigated. The w/c and the fa/ta ratios are important parameters in mix design and affect wave behaviors in concrete. Load-controlled uni-axial compression tests were performed on concrete specimens. Ultrasonic wave measurements were also performed during the compression tests. The stretching coda wave interferometry method was used to obtain the relative velocity change of ultrasonic waves with respect to the stress level of the specimens. From the experimental results, it was found that the w/c ratio greatly affects the acoustoelastic coefficient while the fa/ta ratio does not. The acoustoelastic coefficient increased from $0.003073MPa^{-1}$ to $0.005553MPa^{-1}$ when the w/c ratio was increased from 0.4 to 0.5. On the other hand, the acoustoelastic coefficient changed in small from $0.003606MPa^{-1}$ to $0.003801MPa^{-1}$ when the fa/ta ratio was increased from 0.3 to 0.5. Finally, it was also found that the relative velocity change has a linear relationship with the stress level of concrete.

• 설비공학논문집
• /
• 제27권5호
• /
• pp.277-282
• /
• 2015

During hot and humid weather, air-conditioners consume a large amount of electricity due to the large amount of latent heat. Simultaneous usage of a dehumidifier may reduce latent heat and reduce electricity consumption. In this study, dehumidification performance was measured for a small-sized dehumidification rotor made of inorganic fiber impregnated with metallic silicate within a constant temperature and humidity chamber. Regeneration to dehumidification depends on ratio, rotor speed, room temperature, regeneration temperature, room relative humidity and frontal velocity to the rotor. Results demonstrate an optimum area ratio (1/2), rotor speed (1.0 rpm), and regeneration temperature ($100^{\circ}C$) to achieve a dehumidification rate of 0.0581 kg/s. As the area ratio increases, the optimum rotation speed and the optimum regeneration temperature also increase. Above the optimum rotor speed, incomplete regeneration reduces dehumidification. Above the optimum regeneration temperature, increased temperature variation between regeneration and dehumidification reduces dehumidification. Dehumidification rate also increases with an increase of relative humidity, dehumidification temperature and flow velocity into the rotor.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.42-45
• /
• 2002

General wheel mark in mono-crystalline silicon wafer finding is able to be expected because it depends on radius ratio and angular velocity ratio of wafer and wheel. The pattern is predominantly determined by the contour of abrasive grits resulting from a relative motion. Although such a wheel mark is made uniform pattern if the process parameters are fixed, sub-surface defect is expected to be distributed non-uniformly because of characteristic of mono-crystalline silicon wafer that has diamond cubic crystal. Consequently it is considered that this phenomenon affects the following process. This paper focused on kinematic analysis of wafer grinding process and simulation program was developed to verify the effect of process variables on wheel mark. And finally, we were able to predict sub-surface defect distribution that considered characteristic of mono-crystalline silicon wafer

• 한국지반공학회논문집
• /
• 제31권9호
• /
• pp.17-27
• /
• 2015

벤더엘리먼트가 장착된 삼축압축시험장비를 이용하여 모래에 대한 일련의 압밀배수시험을 수행하였다. 상대밀도 및 유효구속응력 조건을 달리하여 각각의 조건별 응력-변형률 관계를 측정하였으며, 압밀이 종료된 시점에서의 전단파 속도를 측정함으로써 전단파 속도와 간극비, 유효응력, 그리고 전단강도와의 상관관계를 분석하였다. 분석 결과, 미소변형률에서의 전단파 속도로부터 계산된 최대전단탄성계수와 파괴 시의 축응력과 압밀 시의 구속응력의 합으로 정의되는 유효수직응력간에는 고유한 상관관계가 존재하는 것으로 나타났다. 도출된 전단탄성계수와 유효수직응력간의 상관관계는 유효구속응력을 정규화시킴으로써 정확도를 향상시켰다. 본 연구를 통해 제시된 상관관계를 통해 전단강도 및 내부 마찰각을 예측하였을 시, 실제 실내 시험을 통해 산출된 내부 마찰각을 정확하게 예측할 수 있는 것으로 나타났다. 이는 미소변형률에서의 전단파 속도를 기반으로 신뢰성 높은 파괴 시 전단강도, 나아가 내부 마찰각까지 예측이 가능하다는 것을 의미하며 기존 SPT-N value와 경험식을 통해 내부 마찰각을 예측하여 설계에 적용하는 방식의 불확실성을 개선해 줄 수 있는 매우 유용한 방법이라고 판단된다.

• 한국기계가공학회지
• /
• 제12권6호
• /
• pp.69-76
• /
• 2013

This paper presents the development of the FCF method for the manufacturing of final products using numbers related to the minimum amount of work. The utilized product is a drum clutch, which is part of the transmission of an automobile. A double acting press is secured first and a prediction of the forming load on the practical material is made through an experiment with a plasticine model. Also, a finite element simulation using product shape and properties is performed, as well as a press experiment. A double acting press is manufactured that is suitable for a double acting experiment with a conventional hydraulic press(200 tons). A peripheral device for the press is additionally designed for experimental purposes. And, the press has as its essential points the drive speed, stroke control, etc., all of which influence the forming and is modified. Especially, a laser system is used for velocity measurement of two punches. The forming load of a practical material is predicted in order to derive a forming load formula for cold conditions on the basis of approximate similarity theory. Finite element analysis of the relative velocity ratio(RVR), etc., for most suitable flow defect(unfilling, etc.) prevention is achieved as well. The results are verified through a press experiment.

• 한국자동차공학회논문집
• /
• 제9권2호
• /
• pp.185-191
• /
• 2001

In many papers, the powertrain system generally has been madeled as one-dimensional torque model. One-dimensional powertrain model may calculate the torque correctly but it does not consider the non-rotational degrees-of-freedom of the powertrain components and the interaction of these degrees-of-freedom with the vehicle body frame and suspension. To consider the non-rotational degrees of freedom, the differential is modeled as a three-dimensional rigid body in this paper. A constant velocity joint is newly formulated and a relative constraint is also formulated to model the motion transfer due to gear ratio of the differential. Implementing the proposed powertrain system in the multibody model, more detail dynamic responses can be obtained. Obtained outputs such as reaction torques on the constant velocity joint and reaction forces on the rack can be useful data in the design of a powertrain.

• 한국항공우주학회지
• /
• 제31권4호
• /
• pp.82-91
• /
• 2003

이중 충돌형(unlike doublet impinging) 분사기의 직경변화에 따른 혼합특성을 모사 추진제에 의한 실험적인 방법으로 연구하였다. 분사유동은 레이놀즈수 2,500부터 12,000 사이의 난류제트를 사용하였으며, 분사공 직경 비를 1부터 1.5까지 확대시켜 직경변화에 따른 혼합특성을 고찰하였다. 분사공의 형상변수는 최적의 혼합특성을 갖는 설계치로 고정하였으며, 대기압 하의 분사유동장의 공기역학적 영향은 배제하였다. 매개변수로서 운동량비를 사용하여 혼합효율의 변화(mixing doublet impinging)를 고찰하였으며, 패터네이터(patternater)를 사용하여, 연료와 산화제의 국소 질량분포 측정 및 혼합비 분포를 측정하였다. 운동량비와 혼합효율의 상관성을 침투정도로 고려하여 연료와 산화제의 속도비와 혼합효율의 상관성을 고찰하였다. 분사공 직경이 증가됨에 따라 최대 혼합효율점이 운동량비가 증가되는 방향으로 이동함을 보였으며, 연료와 산화제의 속도 비 0.65~0.7영역에서 분사공 직경변화와 무관하게 혼합효율이 최대가 되었다. 또한 혼합효율은 추진제의 분사 충돌 시 상대제트의 침투 깊이 정도에 따라 큰 영향을 받는 것으로 나타났다.