• 한국지반신소재학회논문집
• /
• 제11권4호
• /
• pp.27-35
• /
• 2012

국내에 적용되고 있는 블록식 보강토 옹벽의 전면벽체는 보강재의 고정 및 뒷채움재의 유실방지 역할을 하지만, 벽체에 작용하는 하중에 대한 역학적 기능은 부족하다. 보강토체를 구성하는 벽체에 휨 및 전단에 대한 저항 성능을 부여하기 위하여 개발된 강성벽 일체형 보강노반은 다양한 장점에도 불구하고, 기존 공법과 비교하여 경제성 및 시공성 측면에서 단점이 부각되어 현장에의 적용은 미루어져 왔다. 본 연구에서는 강성벽 일체형 보강노반의 국내 적용성 향상을 목적으로 강성벽의 성능은 확보하면서 경제성 및 시공성을 향상시키기 위한 보강재 연직 배치 간격 및 길이 변화가 보강토체 전체의 거동에 미치는 영향을 평가하였다. 이를 위하여 강성벽을 갖는 1/10 축소모형 보강토체 및 높이 3m의 실내 실대형 시험체를 조성하고, 모사 열차하중 하에서의 변형 특성을 평가하였다. 시험 결과 비록 짧은 보강재를 사용함에도 불구하고 강성벽 보강노반에서 벽체 수평 발생변위 및 침하는 허용한계 수준 이하이었으며, 보강재 연직 배치간격이 30cm에서 40cm로 증가하여도 사용성 측면에서의 성능 수준에는 큰 변화가 없는 것을 확인할 수 있었다.

• 토지주택연구
• /
• 제6권1호
• /
• pp.11-19
• /
• 2015

이 논문에서는 최근 강화된 내진규정에 의하여 현장에서 시공에 어려움을 겪고 있는 특수전단벽의 배근상세를 완화할 목적으로 제안된 경계요소 횡보강상세에 대하여 횡보강근의 형태와 배근간격에 따른 실험결과를 제시하고 있다. 실험결과, 제안된 횡보강 상세를 채용한 실험체의 균열 및 파괴양상은 폐쇄형 후프를 사용한 실험체와 유사한 경향을 나타내었으며, 최대강도도 예상값을 모두 상회하는 것으로 나타났다. 또한, 에너지 소산능력을 비교한 결과, 완화된 배근상세를 따르는 실험체(SSWR2)의 경우 기존 설계기준의 특수전단벽 실험체(SSW2)와 유사한 내진성능을 가지고 있는 것으로 나타났으며, 설계기준에서 제시하고 있는 1.5% 수준의 변형각 조건을 충분히 만족하고 있어 구조물의 주요 횡력저항 요소로서 사용될 수 있을 것으로 판단된다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제21권2호
• /
• pp.1-12
• /
• 2017

본 연구에서는 대골형 파형강판 합성부재의 구성요소를 고강도 재료로 대체하고 이음방법, 전단보강방법 등 단면구성방법에 따른 단위부재의 휨거동을 분석하여 대골형 파형강판 합성부재 구조물의 장대화 및 적용범위확대를 위한 기초자료를 제시하고자 하였다. GR40과 SS590 강재를 적용한 합성구조체의 휨실험 결과, SS590 파형강판을 적용한 경우 정모멘트 하중저항성능은 약 28%가 증가되는 것으로 확인되었으나 부모멘트 저항성능은 미미한 것으로 확인되었다. 볼트의 개수를 증가시킨 파형강판 이음방법의 정모멘트 및 부모멘트 저항성능증가율은 높지 않은 것으로 확인되었다. 이는 고강도 재료에 따른 볼트의 접합 특성(볼트중심에서 연단까지의 거리, 볼트중심간 간격 등)이 거동에 영향을 미쳤기 때문인 것으로 추정된다. 전단보강재 간격별 휨실험 결과, 보강재 간격이 감소할수록 정모멘트에 대한 하중저항성능, 부모멘트에 대한 변위저항성능이 향상되는 것으로 확인되었다. 전단보강재 형상별 휨실험결과, U형 보강재 적용에 따른 정 부모멘트 저항성능 증가율은 약 2%~7% 로 낮았다. 따라서 대골형 파형강판 합성부재의 휨성능증가에는 파형강판의 강종, 전단보강재 간격, 보강철근의 특성이 주요한 영향을 미치는 것으로 판단된다.

• Earthquakes and Structures
• /
• 제7권5호
• /
• pp.779-796
• /
• 2014

This experimental investigation was conducted to examine the behavior and response of high-strength material (HSM) reinforced concrete (RC) columns under combined high-axial and cyclic-increasing lateral loads. All the columns use high-strength concrete ($f_c{^{\prime}}$=100MPa) and high-yield strength steel ($f_y$=685MPa and $f_y$=785MPa) for both longitudinal and transverse reinforcements. A total of four full-scale HSM columns with amount of transverse reinforcement equal to 100% more than that required by earthquake resistant design provisions of ACI-318 were tested. The key differences among those four columns are the spacing and configuration of transverse reinforcements. Two different constant axial loads, i.e. 60% and 30% of column axial load capacity, were combined with cyclically-increasing lateral loads to impose reversed curvatures in the columns. Test results show that columns under 30% of axial load capacity behaved much more ductile and had higher lateral deformational capacity compared to columns under the 60% of axial load capacity. The columns using closer transverse reinforcement spacing have slightly higher ductility than columns with larger spacing.

• Advances in concrete construction
• /
• 제1권1호
• /
• pp.103-119
• /
• 2013

The applicability of limit analysis methods in design and assessment of concrete structures generally requires a certain plastic deformation capacity. The latter is primarily provided by the ductility of the reinforcement, being additionally affected by the bond properties between reinforcing steel and concrete since they provoke strain localization in the reinforcement at cracks. The bond strength of reinforcing bars is not only governed by concrete quality, but also by construction details such as bar ribbing, bar spacing or concrete cover thickness. For new concrete structures, a potentially unfavorable impact on bond strength can easily be anticipated through appropriate code rules on construction details. In existing structures, these requirements may not be necessarily satisfied, consequently requiring additional considerations. This two-part paper investigates in a theoretical study the impacts of the most frequently encountered construction details which may not satisfy design code requirements on bond strength, steel strain localization and plastic deformation capacity of cracked structural concrete. The first part introduces basic considerations on bond, strain localization and plastic deformation capacity as well as the fundamentals of the Tension Chord Model underlying the further investigations. It also analyzes the impacts of the hardening behavior of reinforcing steel and concrete quality. The second part discusses the impacts of construction details (bar ribbing, bar spacing, and concrete cover thickness) and of additional structure-specific features such as bar diameter and crack spacing.

• Structural Engineering and Mechanics
• /
• 제87권4호
• /
• pp.333-346
• /
• 2023

This paper presents findings from an experimental study that was focused on evaluating the use of Forta-Ferro (FF) and Polyvinyl Alcohol (PVA) fibers on the response of moderate and special ductility beams under load cycles. For this reason, eight full-scale specimens, identical in geometry, were subjected to gradual cyclic loading. The specimens included two plain concrete beams with medium and special ductility, three beams with medium ductility and stirrup spacing of one-quarter the effective depth (d/4) and three beams with special ductility, and stirrup spacing of one-half the effective depth (d/2), strengthened with FF and PVA fibers separately. The use of fibers was aimed at reducing the amount of shear reinforcement in flexural members. Here, the variation of parameters including the maximum strength, ultimate strength, stiffness, ductility, damage index, energy dissipation, and equivalent damping was studied. Utilizing FF and PVA fibers improved the performance in beams with moderate ductility when compared to those beams with special ductility. Therefore, in special ductility beams, fibers can be used instead of crossties and in moderate ductility beams, fibers can be added to reduce the ratio of shear reinforcement. Furthermore, increasing the stirrup spacing in the moderate ductility beams from d/4 to d/2 and adding 0.6% FF or 1.5% PVA fibers resulted in behavior similar to those of the moderate ductility beam.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.315-324
• /
• 2010

In this study, the pullout tests are conducted to evaluate the pullout resistance of the geosynthetic strip with or without bearing resistance zone. The test results are indicated that the pullout resistance of the geosynthetic strip without bearing resistance zone is not affected by horizontal spacing. However, the horizontal spacing of reinforcement with bearing resistance zone affects the bearing resistance. In other words, it is indicated that the bearing resistance at spacing of 210mm is larger than that at spacing of 260mm. This means that the pullout strength at spacing of 210mm is larger than that at spacing of 260mm. Therefore.

• 콘크리트학회논문집
• /
• 제24권4호
• /
• pp.381-390
• /
• 2012

콘크리트구조설계기준(2003, 2007)의 균열제어방법이 어떠한 연구들에 근거를 두어 제시되었는지 그 발달과정을 검토하였다. 이러한 과정들을 근거로 현행 구조기준의 균열제어방법에 어떠한 문제점들이 발생할 수 있으며 이를 해결하기 위해서는 어떻게 하여야 하는지 제안하였다. 제시한 새로운 균열제어식은 간단하면서도 명확하고 기존의 규정들과 충돌하지 않아 실무자들에게 발생할 수 있는 논란의 여지를 종식시킬 수 있을 것이다.

• Structural Monitoring and Maintenance
• /
• 제7권3호
• /
• pp.167-193
• /
• 2020

In this paper, the behavior of interior steel fiber reinforced concrete beam - column joints (BCJs) under cyclic loading is investigated. An experimental program including tests on twelve reinforced concrete (BCJs) specimens under cyclic loading was carried out. The test specimens are divided into two groups having different geometry: group (G1) (symmetrical BCJs specimens) and group (G2) (nonsymmetrical BCJs specimens). The parameters considered in this study are the steel fibers (SFs) content by volume of concrete (V_f), the spacing of shear reinforcement at the joint region, and the area of longitudinal flexural reinforcement. Test results show that the addition of 0.5% SFs with stirrups spacing S=S_max has effectively enhanced the overall performance of BCJs with respect to energy dissipation, ductility ratio, spreading and width of cracks. The failure of specimens is governed mainly by the formation of a plastic hinge at the face column and outside the beam-column junction. Secondary shear cracks were also observed in the beam-column junctions.

• Computers and Concrete
• /
• 제4권5호
• /
• pp.403-424
• /
• 2007

The investigation of corrosion effects on the tensile behavior of reinforced concrete (RC) members is very important in region prone to high corrosion conditions. In this article, an experimental study concerning corrosion effects on tensile behavior of RC members is presented. For this purpose, a comprehensive experimental program including 58 cylindrical reinforced concrete specimens under various levels of corrosion is conducted. Some of the specimens (44) are located in large tub containing water and salt (5% salt solution); an electrical supplier has been utilized for the accelerated corrosion program. Afterwards, the tensile behavior of the specimens was studied by means of the direct tension tests. For each specimen, the tension stiffening curve is plotted, and their behavior at various load levels is investigated. Average crack spacing, loss of cross-section area due to corrosion, the concrete contribution to the tensile response for different strain levels, and maximum bond stress developed at each corrosion level are studied, and their appropriate relationships are proposed. The main parameters considered in this investigation are: degree of corrosion ($C_w$), reinforcement diameter (d), reinforcement ratio (${\rho}$), clear concrete cover (c), ratio of clear concrete cover to rebar diameter (c/d), and ratio of rebar diameter to reinforcement percentage ($d/{\rho}$).