• Steel and Composite Structures
• /
• 제28권6호
• /
• pp.719-734
• /
• 2018

Prior to the introduction of modern seismic guidelines, it was a common practice to provide straight bar anchorage for beam bottom reinforcement of gravity load designed building. Exterior joints with straight bar anchorages for beam bottom reinforcements are susceptible to sudden anchorage failure under load reversals and hence require systematic seismic upgradation. Hence in the present study, an attempt is made to upgrade exterior beam-column sub-assemblage of a three storied gravity load designed (GLD) building with single steel haunch. Analytical formulations are presented for evaluating the haunch forces in single steel haunch retrofit. Influence of parameters that affect the efficacy and effectiveness of the single haunch retrofit are also discussed. The effectiveness of the single haunch retrofit for enhancing seismic performance of GLD beam-column specimen is evaluated through experimental investigation under reverse cyclic loading. The single steel haunch retrofit had succeeded in preventing the anchorage failure of beam bottom bars of GLD specimen, delaying the joint shear damage and partially directing the damage towards the beam. A remarkable improvement in the load carrying capacity of the upgraded GLD beam-column sub-assemblage is observed. Further, a tremendous improvement in the energy dissipation of about 2.63 times that of GLD specimen is observed in the case of upgraded GLD specimen. The study also underlines the efficacy of single steel haunch retrofit for seismic upgradation of deficient GLD structures.

• Steel and Composite Structures
• /
• 제52권4호
• /
• pp.451-460
• /
• 2024

Hollow reinforced concrete columns confined with GFRP tubes (GRCH) are composite members composed of the outer GFRP tube, the PVC or other plastic tube as the inner tube, and the reinforced concrete between two tubes. Because of their high ductility, light weight, corrosion resistance and convenient construction, many researchers pay attention to the composite members. However, there are few studies on GRCH members under eccentric compression compared with those under axial compression. Eight hollow columns were tested under eccentric compression, including one axial compression column and seven eccentric compression columns. The failure modes and force mechanisms of GRCH members were analyzed, considering the varying in hollow ratio, reinforcement ratio and eccentricity. The test results showed that configuring steel bars can greatly increase the bearing capacity and ductility of the members. Each component (GFRP tube, concrete, steel bar) had good deformation coordination and the strength of each material could be fully utilized. But for specimens with larger eccentricity ratio (e_r=0.4) and larger hollow ratio (χ=0.55), the restraining effect of GFRP tube on concrete was significantly decreased.

• 한국구조물진단유지관리공학회 논문집
• /
• 제19권3호
• /
• pp.139-148
• /
• 2015

본 논문은 강섬유 대신 철근집합체를 사용하여 초고강도 섬유보강 콘크리트 부재의 최대하중 이후 연성거동을 유도하는 것을 목적으로 한다. 강섬유와 철근집합체의 조합을 가진 직사각형 콘크리트 보에 대한 휨거동 실험을 수행하였다. 강섬유의 혼입률은 0%, 0.7%, 1%, 1.5%, 2%이고, 연성거동을 유도하기 위한 종방향 철근 집합체의 철근비는 0.0036, 0.016, 0.028 그리고 0.036이다. 이러한 실험 요소의 조합으로 15개의 초고강도 콘크리트보가 제작되었다. 강섬유 뿐만 아니라 종방향의 철근 집합체도 초고강도 콘크리트보의 연성거동을 유도하는데 효과를 가지고 있다. 강섬유 혼입률 0.7%와 철근비 0.028인 철근집합체를 사용할 경우 가장 경제적인 조합임을 볼 수 있다. 하중과 처짐관계, 콘크리트 응력의 변화 및 균열양상 등이 좁은 간격을 가진 작은 직경의 종방향 철근 집합체의 유용성을 나타내고 있다.

• 한국강구조학회 논문집
• /
• 제28권1호
• /
• pp.1-12
• /
• 2016

본 연구에서는 스터럽 보강 선설치 앵커의 정적 전단하중에 대한 저항강도 평가를 위한 실험 연구를 수행하였다. 실험변수로는 전면지압철근 유무와 콘크리트 균열 유무로 설정하였다. 앵커는 M36, 연단거리는 180mm로 하였다. 모든 철근은 HD-10 철근을 사용하고 스터럽의 간격은 100mm로 하였다. 실험으로부터 전면지압철근을 설치한 경우 스터럽 저항강도는 16% 증가하였다. 한편 균열 콘크리트에서의 저항강도는 비균열 콘크리트에 비해 5% 감소에 불과하였다. 실험 결과로부터 ACI 318 및 ETAG 001 기준은 스터럽의 저항강도를 안전측으로 평가하였으며, 적절한 강도 평가 방안을 제안하였다. 마지막으로 스터럽 보강 시 앵커 본체의 파괴강도에 대한 고찰을 제시하였다.

• 대한토목학회논문집
• /
• 제28권3A호
• /
• pp.331-340
• /
• 2008

본 연구는 상부 플랜지가 없는 I형 강재 거더, 즉 역T형의 강재 거더의 일부를 콘크리트에 매립한 역T형강-콘크리트 합성바닥판의 구조거동을 실험적 연구를 통해 분석하여 이를 토대로 새로운 개념의 교량 바닥판 상세를 제안하고자 실시하였다. 이를 위해 기존의 철근콘크리트 바닥판과 강합성 바닥판 시험체를 제작하여 정적 휨파괴 시험을 실시하였다. 이로부터 극한 및 최대하중을 평가하였으며, 전단홀 관통 철근의 적용 유무에 따른 구조거동의 변화를 분석하였다. 실험 결과 전단홀 관통 철근을 적용할 경우에는 충분한 전단강도가 확보되어 전형적인 인장파괴 형태를 나타내고, 극한 및 최대하중 모두 철근콘크리트 바닥판보다 높아지는 것을 알 수 있었다. 또한 철근콘크리트 바닥판보다 강합성 바닥판의 처짐이 크게 발생하는 것으로 나타났다.

• 콘크리트학회논문집
• /
• 제22권6호
• /
• pp.833-841
• /
• 2010

이 연구에서는 5개의 철근콘크리트 보-기둥 접합부 실험을 분석하였다. 연구의 주목적은 접합부에 인접한 보의 소성힌지의 영향으로 인한 부착 감소로 발생하는 보 주인장철근 미끄러짐에 따른 접합부 내력 및 연성을 평가하는 것이다. 또한 보 주인장철근량을 변수로 하여 접합부 내력 및 연성에 미치는 영향을 평가하였다. 실험 결과에 의하면 접합부의 전단강도비 $V_{j1}/V_{jby}$가 감소할수록 인접한 보의 소성힌지의 변형률 침투현상은 증가하는 것으로 나타났다. 주인장철근의 미끄러짐은 구간별로 다르게 나타났으며 주인장철근 뽑힘 현상은 접합부 전단강도비 $V_{j1}/V_{jby}$와 관계없이 비슷하게 나타났다. 이것은 주인장철근 뽑힘 현상이 변형률 침투현상만이 아닌 인접한 보의 소성힌지의 축변형에도 영향을 받기 때문이다.

• 도시과학
• /
• 제7권2호
• /
• pp.21-27
• /
• 2018

With the increase of the skyscraper center, the development of large-diameter and high-strength reinforcing bars is being carried out to solve the dense reinforcement. In case of the steel reinforced concrete with a small cross section such as beam-column joints, the development length becomes short when straight bars are used. Therefore, it is possible to solve the problem that the development length becomes short by using the bearing strength of the hooked bar and headed bar. In this study, the exterior beam-column joint test of SD700 hooked bar and headed bar with anchorage length of 20db was conducted to extend the development length limitation of hooked bar and headed bar. As a result of the evaluation of the anchorage strength using the design equation by KCI, the average of the [measured value]/[predicted value] ratio was 1.31 for the hooked reinforcing bars. In the case of headed bars, the average of the [measured value]/[predicted value] ratio was 1.12. In addition, in order to compare the anchorage performance of the hooked bar and the headed bar, the measured values were divided by the square root of the compressive strength of the concrete to compare the anchorage strength. Under the same conditions, the anchorage strength of headed bars was 8.5% higher than the hooked bars.

• Computers and Concrete
• /
• 제19권6호
• /
• pp.631-639
• /
• 2017

This study experimentally investigated the flexural capacity of a concrete beam reinforced with a newly developed GFRP bar that overcomes the lower modulus of elasticity and bond strength compared to a steel bar. The GFRP bar was fabricated by thermosetting a braided pultrusion process to form the outer fiber ribs. The mechanical properties of the modulus of elasticity and bond strength were enhanced compared with those of commercial GFRP bars. In the four-point bending test results, all specimens failed according to the intended failure mode due to flexural design in compliance with ACI 440.1R-15. The effects of the reinforcement ratio and concrete compressive strength were investigated. Equations from the code were used to predict the deflection, and they overestimated the deflection compared with the experimental results. A modified model using two coefficients was developed to provide much better predictive ability, even when the effective moment of inertia was less than the theoretical $I_{cr}$. The deformability of the test beams satisfied the specified value of 4.0 in compliance with CSA S6-10. A modified effective moment of inertia with two correction factors was proposed and it could provide much better predictability in prediction even at the effective moment of inertia less than that of theoretical cracked moment of inertia.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.545-550
• /
• 2000

Bond between reinforcing bars and the surrounding concrete is supposed to safely transfer load in the design process of reinforced concrete structures. Bar with high relative rib area will be studied further not only static load but also dynamic loading conditions to sustain better performance of bond for reinforced concrete structures under earthquake. To determine the bond behavior of high ribbed bars in beam and column joints under repeated loads, 31 pullout specimens were tested. Bond strength increases as relative rib area increases. Also the effect of relative rib area on bond is larger in cyclic loading than in monotonic loading.

• 한국화재소방학회논문지
• /
• 제2권1호
• /
• pp.11-20
• /
• 1988

The success of analyzing the behavior of reinforced concrete structures at elevated temperature greatly depends on how accurately certain thermal properties, especially thermal expansion, specific heat and density thermal conductivity can be determined in a wide temperature range. In this Paper, in order to Predict the behavior of reinforced concrete structure in fire hazards thermal expansion characteristics of normal concrete are formulated through experimental investigation.