• 한국항공우주학회지
• /
• 제33권3호
• /
• pp.78-85
• /
• 2005

본 연구는 재생냉각 시스템 설계를 위한 설계절차를 확립하고, 프로그램을 개발하는 것이다. 재생냉각 시스템 개발을 위한 설계변수를 도출하기 위해서 물을 냉각제로 하는 냉각 시스템을 설계절차에 맞추어 설계하였다. 물을 냉각제로 하는 $250kg_{f}$급 엔진을 이용한 연소시험을 통해서 제안된 예측결과와 실험결과를 비교하였고, 비교적 일치함을 보였다. 이와 같이 검증된 설계 프로그램이 케로신을 냉각제로 하는 재생냉각 시스템에 적용 가능함을 확인하였다. 본 연구를 통해 얻은 기초 자료와 관계식은 실제 액체로켓엔진 설계에 직접 사용 가능할 것이다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2006년도 하계종합학술대회
• /
• pp.625-626
• /
• 2006

An Ultra low power super-regenerative oscillator was implemented with on-chip inductor and quench signal generator. The super-regenerative oscillator detects the signal level as low as -70dBm while consuming only 0.48mA at 1.5V supply voltage. These results indicate that the super-regenerative oscillator can be outstanding candidate the simple, ultra low power receiver design.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.621-626
• /
• 2006

Regenerative evaporative cooling is known as an environment-friendly and energy efficient cooling method. A regenerative evaporative cooler (REC) consisting of dry and wet channels is able to cool down the air stream below the inlet wet-bulb temperature. In the regenerative evaporative cooler, the cooling effect is achieved by redirecting a portion of the air flown out of the dry channel into the wet channel and spraying water onto the redirected air. In this study, a horizontal regenerative cooler is considered. In the horizontal regenerative cooler, the flow direction of evaporating water has a right angle to the flow direction of supply air. This difference was investigated with visualization technique and simplified 2-module performance test was done in a thermo-environment chamber. Optimum design configuration is changed due to the wet channel which are easily fully covered with evaporating water and block the air flow inside the channel. Applying the optimized fin configuration design with the highly wetting surface treatment, a regenerative evaporative cooler was fabricated and tested to Identify the cooling performance improvement and operation characteristics. From the experimental results at the intake condition of $32^{\circ}C$ and 50% RH, the supply temperature was measured to be around $23.4^{\circ}C$. The cooling effectiveness based on the inlet dewpoint temperature was evaluated 73% which is almost close to the design expectation.

• 한국유체기계학회 논문집
• /
• 제17권1호
• /
• pp.35-40
• /
• 2014

A multi-objective optimization of a regenerative fan for enhancing the aerodynamic and aeroacoustic performance was carried out using an integrated fan design system, namely, Total FAN-Regen$^{(R)}$. The Total FAN-Regen$^{(R)}$ was developed for non-specialists to carry out a series of design process, viz., computational preliminary design, three-dimensional aerodynamic and aeroacoustic analyses, and design optimization, for a regenerative fan. An aerodynamic analysis of the regenerative fan was conducted by solving three-dimensional Reynolds-averaged Navier-Stokes equations using the shear stress transport turbulence model. And, an aeroacoustic analysis of the regenerative fan was implemented in a finite/infinite element method by solving the variational formulation of Lighthill's analogy based on the results of the unsteady flow analysis. An optimum shape obtained by Total FAN-Regen$^{(R)}$ shows the enhanced efficiency and decreased sound pressure level as much as 1.5 % and 20.0 dB, respectively, compared to those of the reference design. The performance test was carried out for an optimized regenerative fan to validate the performance of the numerically predicted optimal design.

• 대한기계학회논문집B
• /
• 제30권1호
• /
• pp.16-23
• /
• 2006

The present study aims at establishing the design procedure of regenerative pumps. It is based on the new momentum exchange theory proposed in Yoo, Park and Chung. Salient feature of the present design procedure is that it does not require input of any kinds of empirical design data. Using the design procedure, a prototype regenerative pump has been designed and manufactured to confirm its validity. Comparison between the predicted performance and the experimental measurement reveals that the prototype pump has its maximum efficiency at the design flow rate and that the proposed performance analysis method satisfactorily predicts the machine performance.

• International Journal of Fluid Machinery and Systems
• /
• 제7권3호
• /
• pp.86-93
• /
• 2014

This paper describes performance enhancement of a regenerative blower used for a 20 kW fuel cell system. Two design variables, bending angle of an impeller and blade thickness of an impeller tip, which are used to define an impeller shape, are introduced to enhance the blower performance. Internal flow of the regenerative blower has been analyzed with three-dimensional Navier-Stokes equations to obtain the blower performance. General analysis code, CFX, is introduced in the present work. SST turbulence model is employed to estimate the eddy viscosity. Throughout the numerical analysis, it is found that the thickness of impeller tip is effective to increase the blower efficiency in the present blower. Pressure is successfully increased up to 2.8% compared to the reference blower at the design flow condition. And efficiency is also enhanced up to 2.98 % compared to the reference one. It is noted that low velocity region disturbs to make strong recirculation flow inside the blade passages, thus increases local pressure loss. Detailed flow field inside the regenerative blower is also analyzed and compared.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2005년도 연구개발 발표회 논문집
• /
• pp.378-383
• /
• 2005

The performances of side channel type regenerative blowers were evaluated by the blower performance test, 1-D performance prediction and CFD. The performance prediction method was modified using the results of the performance test and CFD and applied to the design of the new regenerative blowers. The major geometric parameters such as channel height, channel area and expansion angle were decided from the performance prediction method for the improved models and the predicted results were compared with CFD and experimental data. Both of the modified models showed improved efficiency at the operating condition. Especially, model3 could be possible to reduce operating rotating speed, that is benefit to noise performance, because of the high head performance at the design point. The CFD results showed that the performance of the regenerative blower was influenced by the secondary circulatory flow in the channel.

• 한국자동차공학회논문집
• /
• 제13권6호
• /
• pp.38-47
• /
• 2005

In this paper, a regenerative braking algorithm is proposed to make the maximum use of the regenerative braking energy for an independent front and rear motor drive parallel HEV. In the regenerative braking algorithm, the regenerative torque is determined by considering the motor capacity, motor efficiency, battery SOC, gear ratio, clutch state, engine speed and vehicle velocity. To implement the regenerative braking algorithm, HEV powertrain models including the internal combustion engine, electric motor, battery, manual transmission and the regenerative braking system are developed using MATLAB, and the regenerative braking performance is investigated by the simulator. Simulation results show that the proposed regenerative braking algorithm contributes to increasing the battery SOC, which recuperates 60 percent of the total braking energy while satisfying the design specification of the control logic. In addition, a control algorithm which limits the regenerative braking is suggested by considering the battery power capacity and dynamic response characteristics of the hydraulic control module.

• 한국추진공학회지
• /
• 제15권1호
• /
• pp.83-89
• /
• 2011

재생냉각식 액체로켓엔진의 예비 설계 단계에서 연소기 형상을 결정하기 위한 설계 방안을 제안하였다. CEA에서 예측된 연소 후 가스 물성치를 이용하여 로켓의 성능 및 재생냉각 성능을 계산하였다. 요구 추력, 연소실 압력, 주위 압력, 추진제 혼합비에 대해 1차원 관계식과 경험식으로 최적 유량과 연소기 성능을 예측하고, Rao 노즐 설계 기법을 활용하여 최종적으로 연소기 형상을 결정할 수 있는 방안을 제시하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.37-42
• /
• 2010

재생냉각식 액체로켓엔진의 예비 설계 단계에서 연소기 형상을 결정하기 위한 설계 방안을 제안하였다. CEA에서 예측된 연소 후 가스 물성치를 이용하여 로켓의 성능 및 재생냉각 성능을 계산하였다. 요구 추력, 연소실 압력, 주위 압력, 추진제 혼합비에 대해 1차원 관계식과 경험식으로 최적 유량과 연소기 성능을 예측하고, Rao 노즐 설계 기법을 활용하여 최종적으로 연소기 형상을 결정할 수 있는 방안을 제시하였다.