• Journal of the Optical Society of Korea
• /
• v.18 no.4
• /
• pp.370-376
• /
• 2014

We optimized the design of the flat encapsulant of a light-emitting diode (LED) package to obtain higher light output power (LOP), both by experiment and simulation using three-dimensional ray-tracing software. In the experiment, the refractive index of the encapsulant was varied (1.41 and 1.53). In addition, double-layer structures with these refractive indices (1.41/1.53) were investigated by varying the shape of the interface between the two among flat, concave, and convex. The experiments showed that the LOP of the double-layer encapsulant with convex interface increased by 13.4% compared to the single-layer encapsulant with a refractive index 1.41, which was explained by the increase of the light extraction efficiency (LEE) in connection with the increase of the critical angle (${\theta}_c$) and the decrease of the Fresnel reflection.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.9
• /
• pp.739-745
• /
• 1998

The objective of this paper is to provide experimental data of Er(rare- earth)doped $SiO_2$thin film made by sputtering methods. The deposition rate of silica glass by sputtering method was 55$\AA$/min. In EDD measurements, the average Er concentration in the deposited film was 0.77(wt%). After annealing at $900^{\circ}C$, the Cl concentration decreased from 3.79(wt%) to 1.52(wt%). The refractive indices of the core $n_1$, cladding $n_2$ were 1.458, 1.558 respectively at 632.8 nm. The refractive index difference between core and cladding, $\Delta$n was 0.1. The refractive index profile of core and cladding interface shows step profile. In the study, $SiO_2$ glass films of Si wafer were successfully doped with active erbium. Therefore, this experimental data will be applicable for fabrications of Er doped planar integrated optical device.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.367-367
• /
• 2013

Commercial applications of indium tin oxide (ITO) can be separated into two useful areas. As it is perceived to bear electrical properties and optical transparency at once, its chance to apply to promising fields, usually for an optical device, gets greater in the passing time. ITO is one of the transparent conducting oxides (TCO), and required to carry the relative resistance less than $10^{-3}{\Omega}$/cm and transmittances over 80 % in the visible wavelength of light. Because ITO has considerable refractive index, there exist applications for anti-reflection coatings. Anti-reflection properties require gradual change in refractive index from films to air. Such changes are obtained from film density or nano-clustered fractional void. Glancing angle deposition (GLAD) method is a well known process for adjusting nanostructure of the films. From its shadowing effects, GLAD helps to deposit well-controlled porous films effectively. In this study, we are comparing the reference sample to samples coated with controlled ITO multilayer accumulated by an e-beam evaporation system. At first, the single ITO layer samples are prepared to decide refractive index with ellipsometry. Afterwards, ITO multilayer samples are fabricated and fitted by multilayer ellipsometric model based on single layer data. The structural properties were measured by using atomic force microscopy (AFM), and by scanning X-ray diffraction (XRD) measurements. The ellipsometry was used to determine refractive indices and extinction coefficient. The optical transmittance of the film was investigated by using an ultraviolet-visible (UV-Vis) spectrophotometer.

• Korean Journal of Optics and Photonics
• /
• v.19 no.3
• /
• pp.182-186
• /
• 2008

The prism spectrometer is a standard device for the measurement of refractive index; it is used in undergraduate laboratories. Typically, however, lots of attention is required in the alignment, and the accuracy of the obtained refractive index is not so high in spite of the durability of the device. The maximum and minimum deviation method, which compensates the disadvantages of the prism spectrometer, can be composed cost effectively using a length marking tape and a rotating platform. It can measure the refractive indices accurately by utilizing a wide screen. In this study, the equal sided hollow prism whose length is 26 mm was fabricated and measured the refractive indices of seven kind of liquids (pure water, $C_3H_5(OH)_2$, $CCl_4$, $C_6H_4NH_2$, $CS_2$, $C_6H_4(CH_3)_2)$ by using the prism spectrometer and maximum and minimum deviated laser beam method at the wavelengths of He-Ne laser (${\lambda}$= 632.8 nm) and YVO4 laser (${\lambda}$= 532 nm). The result shows that the data obtained by the latter method are more accurate and precise than those obtained by the former device.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.12 s.177
• /
• pp.100-107
• /
• 2005

The present work covers a new ray tracing scheme of an injection-molded plastic lens linked with finite element analysis fur injection molding processes. The traditional ray tracing schemes have been based on the assumption that optical property of the lens is homogeneous throughout the entire volume. However, this assumption is quite unrealistic for injection-molded plastic lenses since material properties vary at every point due to injection molding effects. In order to consider non-homogeneous property of a lens, a modified ray tracing method is proposed in connection with finite element analysis of injection molding. Through the analysis of the injection molding process, the distribution of refractive indices can be obtained. This information is then utilized in the proposed ray tracing scheme based on finite element meshes so as to take into account variation of the refractive indices. The effect of mold temperature is also investigated through finite element analysis, and the relevant optical quality is evaluated through the proposed ray tracing simulation.

• Journal of Sensor Science and Technology
• /
• v.30 no.1
• /
• pp.56-60
• /
• 2021

In this study, the relationship between the transmitted light intensity and full-width-at-half-maximum (FWHM) of a Fabry-Perot filter was investigated. The measured refractive indices and absorption coefficients of the fabricated thin films were applied to the Fabry-Perot filter via simulations using optical software. Although considerable research has been conducted on Fabry-Perot filters, this study focused on the usefulness of 4.26-㎛ infrared filtering in carbon dioxide detection. Optical analysis was performed considering the effects of the thickness, refractive indices, and number of thin films in a distributed Bragg reflector. Ultimately, a clear trade-off relationship was observed wherein the transmitted light intensity decreased as the number of multilayers increased; however, the FWHM was observed to be narrower.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.6
• /
• pp.506-511
• /
• 2009

For the application of the photosensitive barrier ribs with optimal properties such as glass transition temperature, refractive index and coefficient thermal expansion, the boro-silicate glasses was studied. The glass transition temperature, coefficient thermal expansion, and refractive index of the glasses based on the $B_2O_3-Al_2O_3-Al_2O_3-SiO_2$ glass system have been investigated with the different ratio of BaO/$Na_2O$ and $B_2O_3/Na_2O$. Increasing the ratio of $B_2O_3/Na_2O$ was led to the increase of coefficient thermal expansion and the decrease of glass transition temperature. The increase of refractive index of boro-silicate glasses increased with the density of glasses. We suggest the empirical equation for the prediction of refractive index with the glass density, $n=0.123{\rho}+1.182$ with 0.042 as the standard deviation in the boro-silicate glass system. The aim of the present paper is to give a basic result of the thermal and optical properties for designing the composition of photosensitive barrier ribs in PDP.

• Korean Journal of Optics and Photonics
• /
• v.9 no.3
• /
• pp.168-174
• /
• 1998

We have measured nonlinear refractive index and nonlinear absorption coefficient of optical materials by using a far-field phase modulation technique. The phase variation of the probe beam in the nonlinear material is transformed into the spatial phase modulation in the far-field so that the spatial distribution of the optical intensity in conjunction with the computer simulation analysis can give the nonlinear optical constants. We have obtained the nonlinear refractive indices and nonlinear absorption coefficient of $CS_2$ and $BaF_2$ by fitting the experimental values and numerical simulation analysis of far-field measurements. The nonlinear refractive indices of $CS_2$ and $BaF_2$were obtained as $1.2{\times}10^{-11}$ esu and $1.0{\times}10^{-13}$ esu, respectively at 616 nm, and the nonlinear absorption coefficient of BaF$_2$as $5.0{\times}10^{-11}$cm/W at 308nm. These measured values were in good agreement with previous reports.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.5
• /
• pp.31-40
• /
• 2002

We propose a novel ultra-short asymmetric vertical directional coupler switch (VDCS) with high extinction ratios larger than 30㏈ composed of switching operation induced section (SOIS), extinction ratio adjusted section (ERAS), and extinction ratio enhanced section (ERES). In this VDCSs, switching operation is achieved by changing the refractive index of one core in SOIS. The improvement of extinction ratios larger than 30㏈ for both cross and bar states is achieved by controlling the asymmetry of refractive indices between both cores in ERES. After propagating through ERAS with symmetry in the structure, different extinction ratios between cross and bar states at the end of SOIS are changed to the same value. For this reason, the optimum asymmetry of the refractive indices of cores to have the maximum extinction ratios and the lengths of ERES are the same for cross and bar states. Design guidelines to achieve high extinction ratios with large tolerances are presented.

• Asian Journal of Atmospheric Environment
• /
• v.6 no.4
• /
• pp.304-313
• /
• 2012

In this study, the ${\AA}$ngstrom exponent for polydispersed aerosol during dynamic processes was investigated. Log-normal aerosol size distribution was assumed, and a sensitivity analysis of the ${\AA}$ngstrom exponent with regards the coagulation and condensation process was performed. The ${\AA}$ngstrom exponent is expected to decrease because of the particle growth due to coagulation and condensation. However, it is difficult to quantify the degree of change. In order to understand quantitatively the change in the ${\AA}$ngstrom exponent during coagulation and condensation, different real and imaginary parts of the refractive index were considered. The results show that the ${\AA}$ngstrom exponent is sensitive to changes in size distribution and refractive index. The total number concentration decreases and the geometric mean diameter of aerosols increase during coagulation. On the while, the geometric standard deviation approaches monodispersed size distribution during the condensation process, and this change in size distribution affects the ${\AA}$ngstrom exponent. The degree of change in the ${\AA}$ngstrom exponent depends on the refractive index and initial size distribution, and the size parameter changes with the ${\AA}$ngstrom exponent for a given refractive index or chemical composition; this indicates that the size distribution plays an important role in determining the ${\AA}$ngstrom exponent as well as the chemical composition. Subsequently, this study shows how the ${\AA}$ngstrom exponent changes quantitatively during the aerosol dynamics processes for a log-normal aerosol size distribution for different refractive indices; the results showed good agreement with the results for simple analytic size distribution solutions.