• Current Optics and Photonics
• /
• v.8 no.1
• /
• pp.38-44
• /
• 2024

Under the influence of atmospheric turbulence, a star's point image will shake back and forth erratically, and after exposure the originally small star point will spread into a huge spot, which will affect the ground calibration of the star sensor. To analyze the impact of atmospheric turbulence on the positioning accuracy of the star's center of mass, this paper simulates the atmospheric turbulence phase screen using a method based on a sparse spectrum. It is added to the static-star-simulation device to study the transmission characteristics of atmospheric turbulence in star-point simulation, and to analyze the changes in star points under different atmospheric refractive-index structural constants. The simulation results show that the structure function of the atmospheric turbulence phase screen simulated by the sparse spectral method has an average error of 6.8% compared to the theoretical value, while the classical Fourier-transform method can have an error of up to 23% at low frequencies. By including a simulation in which the phase screen would cause errors in the center-of-mass position of the star point, 100 consecutive images are selected and the average drift variance is obtained for each turbulence scenario; The stronger the turbulence, the larger the drift variance. This study can provide a basis for subsequent improvement of the ground-calibration accuracy of a star sensitizer, and for analyzing and evaluating the effect of atmospheric turbulence on the beam.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.5
• /
• pp.718-724
• /
• 2006

The heterogeneous association behaviour of various concentration binary mixtures of mono alkyl ethers of ethylene glycol with ethyl alcohol were investigated by dielectric measurement in benzene solutions over the entire concentration range at 25 ${^{\circ}C}$. The values of static dielectric constant $\epsilon_0$ of the mixtures were measured at 1 MHz using a four terminal dielectric liquid test fixture and precision LCR meter. The high frequency limiting dielectric constant $\epsilon_\infty$ values were determined by measurement of refractive index $n_D$ ($\epsilon_\infty\;=\;n_D\;^2$). The measured values of $\epsilon_0$ and $\epsilon_\infty$ were used to evaluate the values of excess dielectric constant $\epsilon^E$, effective Kirkwood correlation factor $g^{eff}$ and corrective correlation factor $g_f$ of the binary polar mixtures to obtain qualitative and quantitative information about the H-bond complex formation. The non-linear behaviour of the observed $\epsilon_0$ values of the polar molecules and their mixtures in benzene solvent confirms the variation in the associated structures with change in polar mixture constituents concentration and also by dilution in non-polar solvents. Appearance of the maximum in $\epsilon^E$ values at different concentration of the polar mixtures suggest the formation of stable adduct complex, which depends on the molecular size of the mono alkyl ethers of ethylene glycol. Further, the observed $\epsilon^E$ < 0 also confirms the heterogeneous H-bond complex formation reduces the effective number of dipoles in these polar binary mixtures. In benzene solutions these polar molecules shows the maximum reduce in effective number of dipoles at 50 percent dilutions. But ethyl alcohol rich binary polar mixtures in benzene solvent show the maximum reduce in effective number of dipoles in benzene rich solutions.

• Korean Journal of Food Science and Technology
• /
• v.25 no.5
• /
• pp.438-443
• /
• 1993

Physico-chemical properties of glucitol fatty acid polyesters (GPE)-one of the potential fat substitutes-were analyzed and compared with conventional edible oil. The refractive Index, apparent viscosity and melting point of S-GPE (soybean oil GPE) were 1.472, 103 cps. at $37^{circ}C\;and\;-53^{\circ}C$, respectively. S-GPE were liquid at room teperature and the Yellowness of S-GPE was slightly stronger than that of soybean oil. The acid value and smoke point of S-GPE were 0.06 and $200^{\circ}C$. To supplement the weak thermal stability of S-PEG, SP-GPE (soybean-palm blended oil GPE) was prepared with soybeanpalm blended oil (70% of soybean oil and 30% of palm oil). The appearance and color of SP-GPE was not much different from S-GPE but the smoke point of that was increased to $210^{\circ}C$. It means that thermal stability of GPE can be enhanced by increasing saturation of the fatty acid composing GPE. Because most of physico-chemical properties of S-GPE or SP-GPE were similar to conventional edible oil, they are expected to be considered as a potential fat substitute with further study for confirming the safety.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.7
• /
• pp.575-582
• /
• 2000

The Electrical conduction and optical properties of Ta$_{2}$/O$_{5}$ thin films as the insulators in DRAM capacitors were studied. Liquid Ta/sib 2//O sub 5/ were prepared by a sol-gel processing and multiple layers were applied by spin-coating up to thickness of 800$\AA$. At annealing temperature of 300~$600^{\circ}C$ the electrical conduction and specific dielectric constant were discussed the behaivor of carrier were observed by the Thermally Stimulated Current (TSC) at the temperature range of 30~23$0^{\circ}C$. At annealing temperature of 300~$600^{\circ}C$ the samples were found to be amorphous below $600^{\circ}C$ and crystalline over it. The electrical strength was about 2.2 MV/cm at 40$0^{\circ}C$. In spite of noncrystallization over 50$0^{\circ}C$ the increasing of leakage current due to pinholes and increasing creak. The refractive index was obtained maximum (2.2) at 40$0^{\circ}C$. The dielectric constant was obtained maximum(18.6) at 40$0^{\circ}C$. TSC was observed one peak at the temperature range of 30~23$0^{\circ}C$ from sample at 40$0^{\circ}C$. In the case of collecting voltage the peak size is decreased in proportion to collecting voltage and then the peak may be thought carrier to be a ionic space charge.e.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.312-312
• /
• 2013

GaN based light emitting diodes (LEDs) are important devices that are being used extensively in our daily life. For example, these devices are used in traffic light lamps, outdoor full-color displays and backlight of liquid crystal display panels. To realize high-brightness GaN based LEDs for solid-state lighting applications, the development of p-type ohmic electrodes that have low contact resistivity, high optical transmittance and high refractive index is essential. To this effect, indiumtin oxide (ITO) have been investigated for LEDs. Among the transparent electrodes for LEDs, ITO has been one of the promising electrodes on p-GaN layers owing to its excellent properties in optical, electrical conductivity, substrate adhesion, hardness, and chemical inertness. Sputtering and e-beam evaporation techniques are the most commonly used deposition methods. Commonly, ITO films on p-GaN by sputtering have better transmittance and resistivity than ITO films on p-GaN by e-bam evaporation. However, ITO films on p-GaN by sputtering have higher specific contact resistance, it has been demonstrated that this is due to possible plasma damage on the p-GaN in the sputtering process. In this paper, we have investigated the advanced sputtering using plasma damage-free p-electrode. Prepared the ITO films on the GaN based LEDs by e-beam evaporation, normal sputtering and advanced sputtering. The ITO films on GaN based LEDs by sputtering showed better transmittance and sheets resistance than ITO films on the GaN based LEDs by e-beam evaporation. Finally, fabricated of GaN based LEDs by using advanced sputtering. And compared the electrical properties (measurement by using C-TLM) and structural properties (HR-TEM and FE-SEM) of ITO films on GaN based LEDs produced by e-beam evaporation, normal sputtering and advanced sputtering. As a result, It is expected to form plasma damage free-electrode, and better light output power and break down voltage than LEDs by e-beam evaporation and normal sputter.

• Journal of Magnetics
• /
• v.11 no.4
• /
• pp.195-207
• /
• 2006

The recently published and new results on design and fabrication of magnetophotonic crystals of different dimensionality are surveyed. Coupling of polarized light to 3D photonic crystals based on synthetic opals was studied in the case of low dielectric contrast. Transmissivity of opals was demonstrated to strongly depend on the propagation direction of light and its polarization. It was shown that in a vicinity of the frequency of a single Bragg resonance in a 3D photonic crystal the incident linearly polarized light excites inside the crystal the TE- and TM-eigen modes which passing through the crystal is influenced by Brags diffraction of electromagnetic field from different (hkl) sets of crystallographic planes. We also measured the faraday effect of opals immersed in a magneto-optically active liquid. It was shown that the behavior of the faraday rotation spectrum of the system of the opal sample and magneto-optically active liquid directly interrelates with transmittance anisotropy of the opal sample. The photonic band structure, transmittance and Faraday rotation of the light in three-dimensional magnetophotonic crystals of simple cubic and face centered cubic lattices formed from magneto-optically active spheres where studied by the layer Korringa-Kohn-Rostoker method. We found that a photonic band structure is most significantly altered by the magneto-optical activity of spheres for the high-symmetry directions where the degeneracies between TE and TM polarized modes for the corresponding non-magnetic photonic crystals exist. The significant enhancement of the Faraday rotation appears for these directions in the proximity of the band edges, because of the slowing down of the light. New approaches for one-dimensional magnetophotonic crystals fabrication optimized for the magneto-optical Faraday effect enhancement are proposed and realized. One-dimensional magnetophotonic crystals utilizing the second and the third photonic band gaps optimized for the Faraday effect enhancement have been successfully fabricated. Additionally, magnetophotonic crystals consist of a stack of ferrimagnetic Bi-substituted yttrium-iron garnet layers alternated with dielectric silicon oxide layers of the same optical thickness. High refractive index difference provides the strong spatial localization of the electromagnetic field with the wavelength corresponding to the long-wavelength edge of the photonic band gap.

• Asian-Australasian Journal of Animal Sciences
• /
• v.27 no.7
• /
• pp.1003-1012
• /
• 2014

The use of a suitable methodology to quantify the phytate phosphorus ($P_{phy}$) content in both the feed and the excreta from broilers is required to enable accurate calculation of the catalytic efficiency of the phytase supplemented in the feed. This study was conducted to compare 2 analytical methodologies (colorimetry and also high-performance liquid chromatography with a refractive index detector) in order to calculate the phytase efficiency by utilizing the results from the methodology that was shown to be the most appropriate. One hundred and twenty broilers were distributed in a $(4+1){\times}2$ factorial arrangement, corresponding to 4 diets that were equally deficient in P supplemented with increasing levels of phytase (0, 750, 1,500, and 2,250 units of phytase activity - FTU - per kg of feed) plus 1 positive control diet without phytase, supplied to male and female birds. The result indicated that the colorimetric methodology with an extraction ratio of 1:20 (mass of sample in g:volume of the solvent extractor in mL) was shown to be the most adequate. There was no interaction between the phytase level and the sex of the broilers (p>0.05). Males consumed 12% more $P_{phy}$ than did females (p<0.01), but the sex of the broilers did not affect (p>0.05) the excretion and retention coefficient of $P_{phy}$. The increase in the phytase level of the diet reduced (linear, p<0.01) the $P_{phy}$ excretion. The greatest $P_{phy}$ retention was estimated at 87.85% when the diet contained 1,950 FTU/kg (p<0.01), indicating that it is possible to reduce the inorganic P in the formulation at an amount equivalent to 87.85% of the $P_{phy}$ content present in the feed, which, in this research, corresponds to a decrease in 2.86 g of P/kg of the feed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.362-362
• /
• 2014

Atomic layer deposition (ALD) can be regarded as a special variation of the chemical vapor deposition method for reducing film thickness. ALD is based on sequential self-limiting reactions from the gas phase to produce thin films and over-layers in the nanometer scale with perfect conformality and process controllability. These characteristics make ALD an important film deposition technique for nanoelectronics. Tantalum pentoxide ($Ta_2O_5$) has a number of applications in optics and electronics due to its superior properties, such as thermal and chemical stability, high refractive index (>2.0), low absorption in near-UV to IR regions, and high-k. In particular, the dielectric constant of amorphous $Ta_2O_5$ is typically close to 25. Accordingly, $Ta_2O_5$ has been extensively studied in various electronics such as metal oxide semiconductor field-effect transistors (FET), organic FET, dynamic random access memories (RAM), resistance RAM, etc. In this experiment, the variations of chemical and interfacial state during the growth of $Ta_2O_5$ films on the Si substrate by ALD was investigated using in-situ synchrotron radiation photoemission spectroscopy. A newly synthesized liquid precursor $Ta(N^tBu)(dmamp)_2$ Me was used as the metal precursor, with Ar as a purging gas and $H_2O$ as the oxidant source. The core-level spectra of Si 2p, Ta 4f, and O 1s revealed that Ta suboxide and Si dioxide were formed at the initial stages of $Ta_2O_5$ growth. However, the Ta suboxide states almost disappeared as the ALD cycles progressed. Consequently, the $Ta^{5+}$ state, which corresponds with the stoichiometric $Ta_2O_5$, only appeared after 4.0 cycles. Additionally, tantalum silicide was not detected at the interfacial states between $Ta_2O_5$ and Si. The measured valence band offset value between $Ta_2O_5$ and the Si substrate was 3.08 eV after 2.5 cycles.

• Korean Journal of Optics and Photonics
• /
• v.21 no.2
• /
• pp.61-68
• /
• 2010

Optical simulation methods were applied to the edge-lit LED backlight for LCD TV applications in order to optimize the optical structure of the light guide plate(LGP), and thus to improve the uniformity properties by removing the bright spots caused by LED's. The edge-lit LED backlight consisted of three white LED's with a lamp cover, a light guide plate, and a reflection film. When there was no pattern on the entrance side surface of the LGP, the illuminance uniformity was sensitively dependent on the distance d between the LED and the entrance surface. The illuminance uniformity increased with d but its increasing rate slowed down when d was beyond ~ 1.5 mm. When micro-patterns such as a lenticular lens array (LLA) or a serration pattern were formed on the entrance surface, the illuminance uniformity was improved substantially even for the case of very small d. At the same simulation condition, the lightguide with serration pattern showed a better uniformity than that with LLA pattern. Additional improvement could be achieved by changing the refractive index of the micro-patterns. These results suggest that using micro-patterns is a very effective way to reduce the bright spots due to their refracting function for the concentrated incident rays onto the LGP.

• Korean Journal of Food Science and Technology
• /
• v.38 no.1
• /
• pp.1-4
• /
• 2006

Method of analyzing sodium alginate in foods was developed using high performance liquid chromatography (HPLC). HPLC conditions for sodium alginate were: column, MCI GEL $(8\;mm\;i.d{\times}300\;mm)$; mobile phase, deionized water; detector, refractive index detection (sensitivity = 16). Separation of sodium alginate was achieved within 15 min. Sodium alginate showed good linear relationship at 0.1-2.0% range. Correlation coefficient of calibration curve for sodium alginate exceeded 0.999, and detection limit was 0.005%. Recovery rate of sodium alginate in wheat flour dough was 106.67%. This method was successfully applied to analyses of cereals, saccharides, and ice cream, etc. Sodium alginate was detected in chocolate, noodles, and kelp at 0-44.8% range.