• 한국가시화정보학회지
• /
• 제18권3호
• /
• pp.23-34
• /
• 2020

Two-phase flow and heat transfer characteristics during the reflood phase of a single heated rod in the KHU reflood experimental facility were examined. Two-phase flow behavior during the reflooding experiment was carefully visualized along with transient temperature measurement at a point inside the heated rod. By numerically solving one-dimensional inverse heat conduction equation using the measured temperature data, time-resolved wall heat flux and temperature histories at the interface of the heated rod and coolant were obtained. Once water coolant was injected into the test section from the bottom to reflood the heated rod of >700℃, vast vapor bubbles and droplets were generated near the reflood front and dispersed flow film boiling consisted of continuous vapor flow and tiny liquid droplets appeared in the upper part. Following the dispersed flow film boiling, inverted annular/slug/churn flow film boiling regimes were sequentially observed and the wall temperature gradually decreased. When so-called minimum film boiling temperature reached, the stable vapor film between the heated rod and coolant was suddenly collapsed, resulting in the quenching transition from film boiling into nucleate boiling. The moving speed of the quench front measured in the present study showed a good agreement with prediction by a correlation in literature. The obtained results revealed that typical two-phase flow and heat transfer behaviors during the reflood phase of overheated fuel rods in light water nuclear reactors are well reproduced in the KHU facility. Thus, the verified reflood experimental facility can be used to explore the effects of other affecting parameters, such as CRUD, on the reflood heat transfer behaviors in practical nuclear reactors.

• Nuclear Engineering and Technology
• /
• 제55권3호
• /
• pp.999-1008
• /
• 2023

Deformed fuel rods can cause a partial blockage of the flow area in a subchannel. Such flow blockage will influence the core coolant flow and further the core heat transfer during the reflooding phase and subsequent severe accidents. Nevertheless, most of the system analysis codes simulate the accident process based on the assumed flow blockage ratio, resulting in inconsistencies between simulated results and actual conditions. This paper aims to study the influence of flow blockage in severe accident scenario of the CAP1400 reactor. First, the flow blockage model of ISAA code is improved based on the FRTMB module. Then, the ISAA-FRTMB coupling system is adopted to model and calculate the QUENCH-LOCA-0 experiment. The correctness and validity of the flow blockage model are verified by comparing the peak cladding temperature. Finally, the DVI Line-SBLOCA accident is induced to analyze the influence of flow blockage on subsequent CAP1400 reactor core heat transfer and core degradation. From the results of the DVI Line-SBLOCA accident analysis, it can be concluded that the blockage ratio is in the range of 40%-60%, and the position of severe blockage is the same as that of cladding rupture. The blockage reduces the circulation area of the core coolant, which in turn impacts the heat exchange between the core and the coolant, leading to the early failure and collapse of some core assemblies and accelerating the core degradation process.

• Nuclear Engineering and Technology
• /
• 제18권3호
• /
• pp.200-208
• /
• 1986

원자로 냉각 계통의 배관 파열에 근거한 냉각재 상실 사고를 방출계수 0.4에 대하여 분석하였다. 분석은 원자로 냉각계통의 배관 파열에 의하여 발생된 감압부터 노심 복구까지의 전 과도 상태를 포함한다. 계통 열수력과 핵연료 성능 평가를 위하여 BLOWDOWN 단계에서는 RELAP4/MOD6-EM 코드와 RELAP4/MOD6-HOT CHANNEL 코드를 사용하였으며 REFLOOD 단계에서는 RELAP4/ MOD6-FLOOD 코드와 TOODEE2 코드를 각각 사용하였다. LOWER PLENUM 충전을 고려하기 위하여 DOWNCOMER에서 증기-물역방향 유동과 과열벽효과를 근사하여 간단한 해석적 모델이 개발되었다. EOB 발생시의 정보를 근거로 하여 재충전지속 시간과 초기 복구 온도가 계산되었으며 RELAP4/MOD6에 의한 분석결과와 비교하여 상당한 일치를 보였다. 또한, 조기 EOB 발생에 영향을 미치는 계통변수의 연구가 수행되어졌다. DOWNCOMER와 UPPER HEAD사이의 마찰손실이 조기 EOB 발생에 지대한 영향을 미쳤으며 적당한 마찰손실계수의 선택을 통하여 조기 EOB 발생을 방지할 수 있었다. 노심 nodalization이 여섯 개인 경우와 세 개인 경우의 분석 결과가 계통열수력학적 면에서 유사한 결과를 나타내지만, 좋은 결과를 얻기 위하여 전자의 경우가 요구된다.