• 한국공작기계학회논문집
• /
• 제17권1호
• /
• pp.65-70
• /
• 2008

The shape and the material of a reflective sheet affect the amount and the range of retroreflection on incident angle of light, significantly. In this study, the method to determine the shape and the material of the reflective sheet is introduced for the maximum retroreflection. Since the microprism shape with an equilateral triangle base has been used widely, the shape optimization of the microprism shape is carried out. The path of the light within the prism is geometrically calculated to find the relationship between incoming and outgoing light to and from a microprism. The optimal shape of a microprism found by the simulation has almost same figure with the one being used in industry for the maximum retroreflection. It is also found that the refraction index of the reflective sheet is another parameter to control for maximum retroreflection and the range of retroreflection.

• Journal of the Optical Society of Korea
• /
• 제13권1호
• /
• pp.152-157
• /
• 2009

The structure of the prism sheet and the reflective polarizer sheet in the direct - illumination liquid crystal display (LCD) backlight is optimized and fabricated. The apex angle of the prism sheet was changed from 90 degree to 96.5 and 101.5 degree and the angular spread of the diffuser films attached on the reflective polarizer sheet was changed from 7 to 1.5 degrees. The measured view angle, the normal luminance, and the contrast ratio from the optimized backlight unit showed improved optical performances.

• 반도체디스플레이기술학회지
• /
• 제21권2호
• /
• pp.112-116
• /
• 2022

The demand for a rear reflective material is continuing according to the expansion of the bifacial soar module and the effect on the re-reflection of the ground using a back sheet that is not used due to the increase in the supply of the bifacial solar module was confirmed. For analysis, a bifacial solar module with an output of 445W was connected to a single inverter of 49.84kW, and analysis of each two inverters was carried out. In the analysis of the results, it was confirmed that the generation amount increased by 5.25% compared to the case where the back sheet reflective film was not installed and it was confirmed that the increase in the generation amount was the noon time when strong solar radiation was irradiated, not the time of sunrise and sunset.

• 한국정밀공학회지
• /
• 제19권2호
• /
• pp.160-170
• /
• 2002

Retroreflective article is different from other reflecting objects as it returns the incidence ray to the near of its source. This characteristic makes the retroreflectors have many applications in reflective highway signs, reflective vests, and other safety-relaxed items. These articles may have various shapes. However, the quantitative evaluation of performance for the best shape of retroreflector needs much time and cost for manufacturing prototypes and for performance experiments. In this work, we have developed a program for simulating the trace of ray entered into a retroreflective element, in order to determine the optimal shape of retro-reflection. We have also proposed new performance criterion of retroreflective articles, which can confide the range of incidence angle, instead of the criterion with the merely retroreflective strength.

• 대한전기학회논문지
• /
• 제40권6호
• /
• pp.590-597
• /
• 1991

Ion reflective index and sheet resistance in the silicon oblique range smaller than 8 degree and optimization of annealing temperature have been studied. A four point probe was used to obtain the sheet resistance after annealing, while high resolution SIMS was used to determine the Boron and Fluorine atomic profiles before and after annealing. Experimental results and theory of ion reflective index are compared. Ion reflective index was found to decrease according to increasing an ion oblique angle. We introduce a simple analytical model ion reflection, concidering the Rutherford scattering model. This result can not be explained by the conventional Gaussian model.

• 대한공간정보학회지
• /
• 제22권4호
• /
• pp.91-97
• /
• 2014

본 연구에서는 건축물의 구조적 다양성에 따른 토털스테이션 측량과 GPS 측량의 어려움을 보완하고, 무 프리즘 토털스테이션 측량의 건물 재질에 따른 오차 문제를 보완할 수 있는 측량으로 반사시트 토털스테이션 방법을 이용한 건축물 경계 측량의 정확도를 분석하여 지적재조사 측량에서의 활용가능성을 평가하고자 한다. 반사시트 타깃을 거리에 따른 반사각도별로 실험한 결과, 반사각도가 $90^{\circ}$에서는 RMSE가 1.2mm에서 2.8mm로, $60^{\circ}$에서는 2.2mm에서 4.0mm로, $30^{\circ}$에서는 2.5mm에서 4.4mm로 분석되었다. 그리고 실제 건축물의 경계측량을 실험 해본 결과 기존 프리즘과 반사시트 타깃과의 오차는 X축의 RMSE가 0.043m, Y축의 RMSE가 0.038m로 나타났다. 이러한 오차의 발생 원인은 프리즘 소자 뭉치를 건축물의 모서리에 정확히 부착하지 못하는데서 일어나는 오차로 판단된다. 따라서 지적재조사 측량에서 건축물의 경계를 측정할 때 반사시트 타깃을 동시에 활용한다면 건축물의 구조적 문제로 인한 시준의 한계 및 오차 발생에 있어서 상당한 도움이 될 것으로 판단된다.

• 설비공학논문집
• /
• 제28권9호
• /
• pp.350-354
• /
• 2016

Although fibrous insulations are generally used with resistive insulation type, metallic insulation is proper matter to satisfy low head-loss and equipment life when considering the specific condition, especially for Nuclear power plant. Common insulation is resistance insulation with a low thermal conductivity. but RMI is made of sheet plate with low emissivity and closed air space. Thermal radiation is blocked by stainless steel with low emissivity. Thermal conductivity and thermal convection are blocked by closed air space. This study shows the changes and effects of the heat loss according to shape and method of stacking sheet plates inserted into the insulation and analyzed the most optimized way for thermal insulation performance. The result shows that using sheet plate structure through raised and protruding shape processing was the appropriate model to optimize thermal performance. Additionally, insulating performance of RMI improved by placing the sheet plate in a high temperature region intensively.

• Journal of the Optical Society of Korea
• /
• 제13권2호
• /
• pp.256-260
• /
• 2009

The optical performance of the reflective polarizer was investigated over three kinds of direct-lit backlights and/or different configurations of the optical sheets. The optical gain factor achieved by using the reflective polarizer increased as the diffuse nature of the optical sheet was enhanced, because of the more efficient polarization conversion. In addition, the gain factor decreased substantially in flat-lamp backlights compared to tubular-lamp backlights, which was ascribed to the high loss factor during the polarization recycling process due to the complex structure and large area of flat lamps. All these results suggested that reducing the loss factor of the backlight is very important for efficient polarization conversion and thus high optical gain of the reflective polarizer.

• 반도체디스플레이기술학회지
• /
• 제12권3호
• /
• pp.35-39
• /
• 2013

In this paper, we developed an optical sheet for LED lighting with integrated $CO_2$ gas and temperature sensor which can monitor at the indoor environment. The optical sheet for LED lighting is fabricated through PMMA(Polymethyl methacrylate) injection process using mold. This research enables to fabricate the reflective sheet, light-guide plate and the prism sheet in a optical sheet. The fabricated sheet demonstrates higher intensity of optical efficiency compared with single-sided sheets. The $CO_2$ sensor was fabricated using NDIR(NON-Dispersive Infrared) method and it has $0.0235mV/V{\cdot}PPM$ sensitivity. The temperature sensor was fabricated using RTD(Resistance temperature detector) method and it has $0.563{\Omega}/^{\circ}C $sensitivity.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.535-536
• /
• 2006

Researches about micro technology travel lively in these days. Such many researches are concentrated in the field of materials and a process field. But properties of micro materials should be known to give results of research developed into still more. In these various material properties, reliability data such as mechanical, optical, thermal property, etc is the basic property. In this paper, it is measured that is material properties of main BLU(Back Light Unit) components in LCD(Liquid Crystal Display). The pattern shape of prism sheet, diffuser film and reflective plate are measured by variable 3D scanning equipments. It is researched which is the method to measure an optimal 3D pattern shape in each components.