• 음성과학
• /
• 제13권1호
• /
• pp.117-128
• /
• 2006

The two-channel Generalized Sidelobe Canceller (GSC) scheme suffers from the presence of leakage signal in the reference channel. The leakage signal is caused by the dissimilar impulse responses between microphones, and different paths from speech source to microphones. Such leakage is detrimental to speech enhancement of the GSC since the desired reference signal becomes corrupted. In order to suppress the signal leakage, two matrix injection methods are proposed. In the first method, a simple gain compensation matrix is used. In the second, a projection matrix for reducing the error between the actual and the ideal primary and reference signals, is used. This paper describes the performance degradation resulting from leakage, and proposes effective methods to resolve the problem. Representative experiments were conducted to demonstrate the effectiveness of the proposed methods on recorded speech and noise in an actual automobile environment.

• 한국음향학회지
• /
• 제23권4호
• /
• pp.282-287
• /
• 2004

본 논문에서는 참조 신호에 대한 근거리 신호 모델링 기반의 어레이 형상 추정 기법인 근거리 고유벡터 기법을 제안한다. 수중 음원의 방향을 탐지하기 위한 기법들은 일반적으로 참조 신호를 평면파로 가정하고 있다. 그러나 참조 신호가 근거리에 존재하는 경우 평면파 가정으로는 어레이 형상 추정이 불가능하다. 본 논문에서는 참조 신호가 근거리에 존재하는 경우를 위하여 근거리 신호를 모델링하고 이를 기반으로 근거리 고유벡터 기법을 제안하였다. 또한 모의실험을 통해 제안된 기법이 참조 신호의 거리에 관계없이 우수한 형상 추정 성능을 보임을 확인하였다.

• 대한기계학회논문집
• /
• 제18권10호
• /
• pp.2523-2532
• /
• 1994

In this paper, active noise control is performed in a duct system using the periodic pulse train which corresponds to the periodic component of noise source as a reference signal. Control algorithm applied in this study is possible to eliminate the acoustic feedback which occurs in the conventional filtered-x and filtered-u LMS algorithm by using electrical reference signal and has the fast adaptation speed with low filter orders by using synchronous sampling method is discussed via computer simulations and experiments of case studies such as frequency modulation, amplitude modulation and frequency differency between source signal and reference signal.

• Journal of Positioning, Navigation, and Timing
• /
• 제11권4호
• /
• pp.369-379
• /
• 2022

In weighted k-nearest neighbor (WkNN)-based Fingerprinting positioning step, a process of comparing the requested positioning signal with signal information for each reference point stored in the fingerprint DB is performed. At this time, the higher the number of matched base station identifiers, the higher the possibility that the terminal exists in the corresponding location, and in fact, an additional weight is added to the location in proportion to the number of matching base stations. On the other hand, if the matching number of base stations is small, the selected candidate reference point has high dependence on the similarity value of the signal. But one problem arises here. The positioning signal can be compared with the repeater signal in the signal information stored on the DB, and the corresponding reference point can be selected as a candidate location. The selected reference point is likely to be an outlier, and if a certain weight is applied to the corresponding location, the error of the estimated location information increases. In order to solve this problem, this paper proposes a WkNN technique including an outlier removal function. To this end, it is first determined whether the repeater signal is included in the DB information of the matched base station. If the reference point for the repeater signal is selected as the candidate position, the reference position corresponding to the outlier is removed based on the clustering technique. The performance of the proposed technique is verified through data acquired in Seocho 1 and 2 dongs in Seoul.

• 전기학회논문지
• /
• 제65권9호
• /
• pp.1583-1589
• /
• 2016

This paper proposes an improved spread spectrum time domain reflectometry (ISSTDR) using time-frequency correlation and reference signal elimination method in order to have more accurate fault determination and location detection than conventional (SSTDR) despite increased signal attenuation due to the long distance to cable fault location. The proposed method has a two-step process: the first step is to detect a peak location of the reference signal using time-frequency correlation analysis, and the second step is to detect a peak location of the correlation coefficient of the reflected signal by removing the reference signal. The proposed method was validated through comparison with existing SSTDR methods in open-and short-circuit fault detection experiments of low voltage power cables. The experimental results showed that the proposed method can detect correlation coefficients at fault locations accurately despite reflected signal attenuation so that cable faults can be detected more accurately and clearly in comparison to existing methods.

• 한국산학기술학회논문지
• /
• 제17권3호
• /
• pp.450-456
• /
• 2016

케이블에 인가되는 신호로 의사잡음 수열을 사용하여 인가신호와 반사신호의 시간 상관 분석을 실시하여 케이블 고장을 검출하는 STDR (sequence time domain reflectometry)은 노이즈 환경에 강하고, 단선, 합선을 포함한 간헐적 고장의 검출이 가능한 것으로 알려져 있다. 하지만 고장 위치의 거리가 멀거나 경미한 고장의 경우 반사신호의 감쇄가 크고 상관계수가 작아지게 되어, 케이블 고장 판별이 어렵거나 측정 거리 오차가 커진다. 또한 위상과 피크치 검출에 의한 고장 탐지 자동화가 어렵게 된다. 따라서 본 논문에서는 기존의 STDR의 고장 검출 성능을 향상시키기 위해 케이블에 인가되는 인가신호의 상관계수의 최댓값을 검출하고, 다음으로 인가신호를 제거하여 반사신호의 상관계수의 최댓값을 검출하는 알고리즘을 제안하였다. 제안된 방법은 저압 전력 케이블에서의 고장 검출 실험을 통해 성능을 입증하였다. 그 결과 제안된 방법은 신호가 감쇄되더라도 전통적인 STDR보다 고장 여부의 정확한 구분과 위치의 추적이 가능하였다. 또한 기준신호 제거와 상관계수의 정규화를 통해 위상과 최대값 검출 방법을 사용함으로써 자동 고장 판별과 거리 계산에 오류가 발생하지 않았다.

• 제어로봇시스템학회논문지
• /
• 제22권9호
• /
• pp.686-692
• /
• 2016

A Crimp Force Monitor (CFM) is equipment for detecting crimp errors by analyzing crimp signals obtained from force and strain sensors. The analysis is commonly performed by aligning a measured crimp signal with a reference signal and comparing their difference. Current analysis methods often suffer from wrong alignments that result in false negative detections. This paper presents a new crimp signal analysis method in CFM. First, a falling edge alignment is proposed that matches falling edges of the measured and the reference signals by minimizing the absolute difference summation. Second, a signal parameter error is introduced to evaluate the crimp quality difference between the measured signal and the reference. For calculating the signal parameter error, part of a signal is identified and divided into several regions to maximize the signal parameter errors. Experiments showed that the proposed method can improve the signal alignment and accurately detect bad crimps especially with the strain sensor.

• 전력전자학회논문지
• /
• 제21권3호
• /
• pp.215-223
• /
• 2016

In this study, a novel rotor position sensorless estimation method of an interior permanent-magnet synchronous motor is proposed. A square-wave pulsating voltage signal is injected in the estimated synchronous reference frame. This signal is interpreted in the stationary reference frame regardless of the estimated rotor position. Thus, assuming that the position error is nearly zero is unnecessary because the variables in the estimated synchronous reference frame are not used. The rotor position can be exactly calculated from two voltage references and three sampled current feedbacks in the stationary reference frame. The proposed method is easy to implement and helps enhance the bandwidth of the current controller. The validity of the proposed method is verified by simulations and experiments.

• 전기학회논문지P
• /
• 제51권4호
• /
• pp.219-221
• /
• 2002

This paper presents an electric scooter development using blushless DC motor. In recent scooters was to develop for sport leisure and short transportation. Most of scooter are used petroleum gas. This gas scooter has disadvantage to pollute the air. Some of scooters have developed by DC motor which require a brush. However brushless motors have higher maximum speed and greater capacity, save maintenance labour and produce less noise. There is also greater freedom in planing the usage of brushless motors. In this paper we develop an electric scooter driving BLDC motor for design smart system and control speed of scooter with current reference signal to apply voltage to motor by means of three phase inverter. Using accelerator device we generate current reference to control speed and send the current to a MICOM by A/D converter. This MICOM produces the voltage signal and hall sensors signal and PWM controller drive three phase inverter to minimize error between the reference and an actual current.

• 한국전기전자재료학회논문지
• /
• 제23권2호
• /
• pp.89-92
• /
• 2010

A bolometer sensor used in an infrared thermal imaging system has many advantages on the process because it does not need a separate cooling system and its manufacturing is easy. However the sensitivity of the bolometer is low and the fixed pattern noise(FPN) is large, because the bolometer sensor is made by micro electro mechanical systems (MEMS). These problems can be fixed-by using the high performance readout integrated circuit(ROIC) with noise reduction techniques. In this paper, we propose differential delta sampling circuit to remove the mismatch noise of ROIC itself, the FPN of the bolometer. And for reduction of FPN noise, the reference signal compensation circuit which compensate the reference signal by using on-resistance of MOS transistor was proposed.