• Journal of electromagnetic engineering and science
• /
• 제9권3호
• /
• pp.118-123
• /
• 2009

This paper discusses the design and fabrication of a reference signal generator for a naval radar system, including the vibration environment test. The transmit signals of the S-band radar system are synthesized by the reference signal and the phase noise must lower than - 130 dBc/Hz at a 10 kHz offset frequency. To achieve this specification, the phase noise of the reference signal needs to be less than -165 dBc/Hz at a 10 kHz offset. For achieving very low phase noise performance by the reference signal generator, the phase locked loop technique is applied with a 10 Hz loop bandwidth. Also, this reference signal generator has ${\pm}0.35\;ppb$ short-term stability to minimize instant phase errors and high vibration sensitivity against a ship's shaking, unbalanced rotating of antennas and so on.

• 대한전자공학회논문지SD
• /
• 제38권8호
• /
• pp.54-61
• /
• 2001

High-bandwidth DRAM을 위해 1Gb/s의 데이터 전송률까지 동작하고 그 출력 전압 스윙이 온도와 전원 전압(VDD) 변동에 무관한 CMOS open-drain 출력 구조 회로를 설계하였다. 출력 구동 회로는 여섯 개의 binary-weighted NMOS 트랜지스터로 구성되는데, 이 여섯 개 중에서 ON시킬 current control register의 내용은 추가 호로 없이 DRAM 칩에 존재하는 auto refresh 신호를 이용하여 새롭게 수정하였다. Auto refresh 시간 구간동안 current control register를 수정하는데, 이 시간 구간동안 부궤환 (negative feedback) 동작에 의해 low level 출력 전압($V_OL$)이 저전압 밴드갭 기준전압 발생기(bandgap reference voltage generator)에 의해서 만들어진 기준전압($V_{OL.ref}$)과도 같도록 유지된다. 테스트 칩은 1Gb/s의 데이터 전송률까지 성공적으로 동작하였다. 온도 $20^{\circ}C$~$90^{\circ}C$, 전원 전압 2.25V~2.75V영역에서 최악의 경우 제안된 출력 구동 회로의 $V_{OL.ref}$와 $V_OL$의 변동은 각각 2.5%와 725%로 측정된 반면, 기존의 출력 구동 회로의 $V_OL$의 변동은 같은 온도의 전원 접압의 영역에 대해 24%로 측정되었다.

• Journal of Magnetics
• /
• 제21권3호
• /
• pp.330-339
• /
• 2016

A magnetic field sensing system with a single primary sensor and multiple reference sensors deployed locally and orthogonally, was proposed for downlink signal reception and interference cancelling for Through-the-Earth Communication (TEC). This paper mathematically analyzes a design optimization process for a search coil magnetometer (SCM), and applies that process to minimize the bandwidth of the primary SCM for TEC signal reception and the volume of reference SCMs for multiple distributions. The primary SCM achieves a 3-dB bandwidth of 7 Hz, a sensitivity threshold of 120 fT/${\surd}$Hz, and a volume of $2.32{\times}10^{-4}m^3$. The entire sensing system volume is as small as $10^{-2}m^3$. Experiments with interference from industrial frequency harmonics demonstrated an average of 36 dB and 18 dB improvements in signal-to-interference ratio and signal-to-interference plus noise ratio, respectively, using multichannel recursive-least-squares algorithm. Thus, the proposed sensing system can reduce the interference effectively and allows reliable downlink signal reception.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.2120-2125
• /
• 2005

The principal idea of vibration isolation is to filter out the response of the system over the corner frequency. The isolation objectives are to transmit the attitude control torque within the bandwidth of the attitude control system and to filter all the high frequency components coming from vibration equipment above the bandwidth. However, when a reaction wheels or control momentum gyros control spacecraft attitude, vibration inevitably occurs and degrades the performance of sensitive devices. Therefore, vibration should be controlled or isolated for missions such as Earth observing, broadcasting and telecommunication between antenna and ground stations. For space applications, technicians designing controller have to consider a periodic vibration and disturbance to ensure system performance and robustness completing various missions. In general, past research isolating vibration commonly used 6 degree order freedom isolators such as Stewart and Mallock platforms. In this study, the vibration isolation device has 3 degree order freedom, one translational and two rotational motions. The origin of the coordinate is located at the center-of-gravity of the upper plane. In this paper, adaptive notch filter finds the disturbance frequency and the reference signal in filtered-x least mean square is generated by the notch frequency. The design parameters of the notch filter are updated continuously using recursive least square algorithm. Therefore, the adaptive filtered-x least mean square algorithm is applied to the vibration suppressing experiment without reference sensor. This paper shows the experimental results of an active vibration control using an adaptive filtered-x least mean squares algorithm.

• Journal of Information Processing Systems
• /
• 제11권3호
• /
• pp.483-494
• /
• 2015

High Efficiency Video Coding (HEVC) is the most recent video codec standard of the ITU-T Video Coding Experts Group and the ISO/IEC Moving Picture Experts Group. The main goal of this newly introduced standard is for catering to high-resolution video in low bandwidth environments with a higher compression ratio. This paper provides a performance comparison between HEVC and H.264/AVC video compression standards in terms of objective quality, delay, and complexity in the broadcasting environment. The experimental investigation was carried out using six test sequences in the random access configuration of the HEVC test model (HM), the HEVC reference software. This was also carried out in similar configuration settings of the Joint Scalable Video Module (JSVM), the official scalable H.264/AVC reference implementation, running on a single layer mode. According to the results obtained, the HM achieves more than double the compression ratio compared to that of JSVM and delivers the same video quality at half the bitrate. Yet, the HM encodes two times slower (at most) than JSVM. Hence, it can be concluded that the application scenarios of HM and JSVM should be judiciously selected considering the availability of system resources. For instance, HM is not suitable for low delay applications, but it can be used effectively in low bandwidth environments.

• 대한전자공학회논문지SP
• /
• 제46권3호
• /
• pp.68-74
• /
• 2009

본 논문에서는 비디오 부호화기와 복호화기의 참조 영상 버퍼와 메모리 대역폭을 효과적으로 줄이는 방법을 제안한다. 일반적인 비디오 코덱에서 코딩의 효율을 높이기 위하여 이전 프레임들을 참조하는 방법을 많이 사용하는데, 최근에는 메모리 사용 및 메모리와 프로세서 간의 데이터 대역폭의 효율을 높이기 위하여 참조 프레임을 압축하여 저장하는 방법이 연구되고 있다. 이 방법은 이미 압축 및 복원 과정을 통해 열화가 생긴 참조 영상에 대하여 재 압축을 실행하고, 또 기존의 압축 코덱 내부에 부호화기와 복호화기가 추가되는 경우이기 때문에, 화질의 열화를 최소화하면서 복잡도가 낮은 코덱이 요구된다. 이에 관련된 대부분의 연구는 화질의 열화를 최소화하면서 효과적인 재압축을 할 수 있는 방향으로 진행되며 보통 양자화를 위해 고정길이 비트할당 방법을 사용한다. 본 논문에서는 영상의 특성을 고려한 적응적 블록단위 최대-최소 양자화를 통해 복잡도가 낮으면서 화질의 열화를 최소화 한 방법을 제안한다 제안한 방법에서는 $8{\times}8$ 크기의 블록을 기본 처리 단위로 하여 메모리 접근성을 용이하게 하면서, $8{\times}8$ 블록 내부의 $4{\times}4$ 블록 단위로 적응적인 양자화를 적용한다. 실험결과 기존의 고정길이 비트 할당을 통한 재 압축 방법에 대하여 BD-bitrate 관점에서 평균 1.7%, BD-PSNR 관점에서 평균0.03%의 성능향상을 얻을 수 있었다.

• 전력전자학회논문지
• /
• 제20권6호
• /
• pp.517-525
• /
• 2015

A grid connected inverter must be operated as the main electricity source under an isolated condition caused by the grid problem. Conventionally, the dual loop controller is used for the grid inverter, and the controller is used for control under the stand-alone mode. Generally, the PI(Proportional - Integral) controller is highly efficient under a synchronous reference frame, and stable control can be available. However, in this synchronous frame-based control, high-quality DSP is required because many sinusoidal calculations are necessary. When the PI control is conducted under a stationary frame, the controller constructions are made simple so that they work even with a low-price micro controller. However, given the characteristics of the PI controller, it should be designed with the phase of reference voltage considered. Otherwise, the phase delay of the output voltage can occur. Although the current controller also has a higher bandwidth than the voltage controller, distortion of the voltage is difficult to avoid only by the rapid response of the PI controller, as a sudden load change can occur in the nonlinear load. In this study, a new control method that solves the voltage controller bandwidth problem and rapidly copes with it even in the nonlinear load situation is proposed. The validity of the proposed method is proved by simulation and experimental results.

• International Journal of Computer Science & Network Security
• /
• 제24권4호
• /
• pp.206-210
• /
• 2024

Industrial facilities that use modern IT technologies require the ensured reliability and security of information in automated enterprise management. Concurrently, so as to ensure a high quality of communication, it is necessary to expand the bandwidth of communication channels, which are limited by the physical parameters of the radio frequency spectrum. In order to overcome this contradiction, we propose the application of technology fundamental to ultra-wideband signals, in which the ratio between the bandwidth and its central part is greater than "one". For this reason, the information signal is emitted without a carrier frequency - simultaneously within the entire frequency band - provided that the signal level is lower than the noise level. For the transmission of information content, the method of positional-time coding is used, in which each information bit is encoded by hundreds of ultrashort pulses that arrive within a certain sequence. Mathematical models of signals and values observed in wireless communication systems with autocorrelation reception of modulated ultra-wideband signals are furthermore recommended. These assist in identifying features of the dependence of the error probability on the normalized signal-to-noise ratio and the signal base. Comparative analysis has shown that the best noise immunity of the systems considered in this paper is the communication system, which uses the time separation of the reference and information signals. During the first half of the bit interval, the switch closes the output of the transmitter directly to the generator of the ultra-wideband signal - forming a reference signal. In the middle of the bit interval, the switch alternates the output to one of two possible positions depending on the encoding signal - "zero" or "one", forming the information part of the ultra-wideband signal. It should also be noted that systems with autocorrelation reception and separate transmission of reference and information signals, provide a high level of structural signal secrecy. Furthermore, they provide the reliable transmission of digital information, especially in interference conditions.

• 정보처리학회논문지C
• /
• 제11C권7호
• /
• pp.951-958
• /
• 2004

초고속 인터넷 망등의 국내 인터넷의 저변확대로 인해 전자상거래, 인터넷뱅킹, 전자정부, 이메일등 의 많은 서비스와 다양한 정보의 보고로서 인터넷이 사용되고 있다. 근래에는 가상생환환경의 제공과 멀티미디어 서비스를 제공하고자 새로운 미래형 네트워크인 NGN(Next Gener-ation Network)로서 발전하고 있다. 인터넷은 원격지에서도 원하는 정보를 취득할 수 있는 장점이 있는데, 반대 급부로서 상대방의 정보를 허가없이 몰래 추출, 변조하거나 서비스를 제공하는 경쟁사의 서버를 다운시키는 등의 공격이 증대되고 있다. 2000년부터 님다(Nimda) 바이러스, 코드레드(Code Red) 바이러스, 분산서비스 거부 공격(DDoS : Distributed Denial of Service)이 인터넷 전반에 걸쳐 수행되어 네트워크의 사용을 불편하게 하며, 내부 네트워크 트래픽의 비정상적인 증가를 수반했다. 이러한 대역폭 고갈 침해공격에 대하여 네트워크의 유입점에 위치하는 게이트웨이 시스템에 기가비트 이더넷 인터페이스를 갖는 보안네트워크 카드에 재구성 가능한 하드웨어 기능을 제공 가능한 FPGA (Field Programmable Gate Arrart)상에 대역폭 재어기능인 폴리싱(Policing)을 구현한다.

• 한국전자파학회논문지
• /
• 제13권7호
• /
• pp.649-656
• /
• 2002

본 논문에서는 고속 주파수 스위칭 특성을 갖는 디지탈 하이브리드 위상고정루프(DH-PLL: Digital Hybrid Phase-Locked Loops)의 위상잡음을 분석하였다. 기존 위상고정루프에 비하여, 디지탈 하이브리드 위상고정루프는 D/A 변환기에서 발생하는 잡음이 전체 출력위상잡음에 추가되므로 위상잡음이 증가되는 문제점이 있다. 입력기준신호, D/A 변환기, 그리고 전압제어발진기(VCO: Voltage Controlled Oscillator)를 주요 잡음원으로 고려하여, 이것에 의한 위상잡음을 해석적으로 분석하였다. 또한 폐루프 대역과 주파수 합성 분주비(hi)에 따른 위상잡음의 변화를 연구하여 디지탈 하이브리드 위상고정루프의 위상잡음을 최소화하는 최적 폐루프 대역을 결정할 수 있다. 또한, 해석적 방법에 의한 분석 결과와 회로 시뮬레이션에 의한 결과가 동일함을 확인하였다.