• The Korean Journal of Nuclear Medicine Technology
• /
• v.18 no.1
• /
• pp.158-162
• /
• 2014

Purpose: Reference material (RM) is defined as material that is safe and homogeneous enough about specified characteristic that is made with a purpose of using test of measurement or nominal characteristic. Certified reference material (CRM), which is issued by authorized organization, is defined as reference material that provides characteristic value, link uncertainty and retroactivity. The purpose of this paper was to evaluate recovery of radioimmunoassay by Certified Reference Material enclosed with a certificate and therefore to enhance reliability of test. Materials and Methods: WHO certified reference material is purchased from NIBSC (National Institute for Biological Standard and Control, United Kingdom) and made of 3 levels that are C-1 (low concentration), C-2 (medium concentration) and C-3 (high concentration) and measured for kit at the Seoul National University Hospital. Recovery rate is evaluated after measurement at four different days. Results: Recovery rate results using WHO certified reference material are T4 90%, Ferritin 88%, PSA 94%, Prolactin 99%, AFP 94% and TSH 93%. Conclusion: A procedure that appropriate accuracy, precision, specificity, sensitivity, reproducibility, and validate on the subject of kit for radioimmunoassay is essential. Recovery rate assay as extraction efficiency of analysis process is percent about already measuring results of analysis result after all measuring process. This is very important assessment standards of performance evaluation of immunoassay kit. Recovery rate results of 6 type used WHO CRM are satisfactory to 88~99%. This demonstrates that the radioimmunoassay is a very accurate measurement, which is very effectively utilized in clinical practice.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.39-44
• /
• 2005

To validate the rotor performance analysis, 3D Computational Fluid Dynamics(CFD) analysis was performed for tilt rotor aeroacoustic model(TRAM). Also, 3D vehicle with rotating rotors was simulated for rotor power effect analysis. Multiple reference frame(MRF) and sliding mesh techniques were implemented to capture the effect of rotor revolution. CFD results were compared with the wind tunnel test results to validate their accuracy. At helicopter mode, CFD analysis predicted lower thrust than the wind tunnel test but CFD results showed good agreement with the test result at cruise mode. Rotor power effect decreased the lift but did not change drag and pitching moment.

• Design & Manufacturing
• /
• v.12 no.2
• /
• pp.11-15
• /
• 2018

In this study, we proposed three analysis methods to calculate the flatness of torque-angle sensors (TAS). We introduced two statistical and one geometrical methods in evaluating the precision of the flat plane in the axis direction for TAS. To verified the results, we fabricated TAS and a reference sample using a injection molding machine, mold, polyester as a raw material. We measured ($x_i$, $y_i$) position using 3D contact automated system and applied three analysis methods developed for TAS and a reference sample to see the feasibility. While each analysis method has its own pros and cons, the analysis using the shortest optimal distance was the most precise technique for the flatness evaluation of TAS components.

• Natural Product Sciences
• /
• v.16 no.3
• /
• pp.180-184
• /
• 2010

The simple and accurate method was established for the simultaneous determination of (-)-menthone and (-)-menthol in Menthae herba obtained from Korea and China. A quantitative analysis was performed with a gas chromatography-flame ionization detector and reference compounds were separated on a capillary HP-Innowax column (30 m $\times$ 0.23 mm, 0.50 ${\mu}m$, Agilent, MA, USA). The correlation coefficients of the compounds showed good linearity ($r^2$ > 0.9997) over the linear range. The precision, repeatability and stability showed less than 1.7% of relative standard deviation (RSD) values for two compounds. Recovery rates were within the range of 95.72 - 103.76%. The method was applied successfully to analyze 15 samples of Menthae herba and achieved sufficient and specific separation of reference compounds. The principal component analysis (PCA) exhibited the classification of 15 samples according to their locations of origin.

• International Journal of Human Ecology
• /
• v.15 no.2
• /
• pp.43-57
• /
• 2014

Consumers differ with respect to the level of green attitudes and green purchase behavious and different consumer would have different perceptions on green market environment. This study attempted to explain how consumers perceive green market environment differently across different consumer groups in attitude-behaviour dimension in green consumption. After identifying the four consumer groups based on their attitude toward green purchase and green purchase behaviours, a multinomial logistic analysis and a stepwise discriminant analysis were conducted. This study found that reliability in green market was the most critical factor that contributes to enlarge positive green consumers. Also, the role of reference persons and adequate price of green products were also found to be important to stimulate green buying. By understanding the different role of those factors in each group of consumers, this study provided group-specific implications to expand green consumers.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.12
• /
• pp.45-54
• /
• 2014

This paper presents a lecture note of pu method for power system analysis. The author tries to help students in class better understand the fundamental of pu calculation using a very simple DC circuit. And a voltage drop calculation by pu method for a distribution system is given to help understand the importance of the vector reference in AC circuit analysis. A short current calculation by pu method for a power system with a generator, transformer and transmission line is also presented to show how pu calculation can be applied to real power systems, in which all the data are the ones currently being used by KEPCO and other industrial sites.

• Journal of the Korean Society of Tobacco Science
• /
• v.33 no.1
• /
• pp.28-38
• /
• 2011

This experiment was conducted as a part of Asia collaborative study on purpose of verifying the difference between CM6 and CM7 including 3R4F for reference. It carried out using various analytical categories for example, main stream, sidestream and Av. smoke. Additional analysis such as physical properties, blending ratio, combustibility and general leaf component analysis also implemented in order to investigate the difference. We complied with ISO standard and CORESTA recommended method during analytical operating procedures. In this study, we described that comparative analytical result for CM6 and CM7 known as reference or monitoring cigarettes including 3R4F for reference. All sample cigarettes were conditioned at $22^{\circ}C$, 60% relative humidity for 48 hours. Av. Smoke, MS and SS smoke analysis were performed over five times with two smoking condition, ISO and Health Canada with the exception of Av. smoke analysis. We complied with ISO standard method during analytical operating procedures. And, we conducted additional analysis, such as physical properties, blending ratio, combustibility and leaf component analysis also in order to investigate the difference. In conclusion, we found out some differences between CORESTA monitoring cigarette No. 6 and No 7. The smoke components such as total particulate matters, NFDPM, nicotine and carbon monoxide contents of CM7 were a little lower than CM6. And, these phenomena were the same as not only main stream smoke but also side stream smoke and Av. smoke. This tendency was consistent with ISO and Health Canada smoking condition. Besides, leaf constituents' color of CM7 was darker than CM6. In case of combustibility, it showed short combustion time approximately 30 seconds.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.6
• /
• pp.103-110
• /
• 2011

The aim of this study was to analysis the Heating/cooling performance and Daylighting performance of Solar Window System built in apartments. the solar window is the idea to integrate daylight as a third form of solar energy into a PV/Solar Collector system. The process of this study is as follows: 1)Solar Window system was designed through the investigation of previous paper and work. 2)The simulation program(Lightscape3.2) was used in daylighting performance analysis. the reference model of simulation was made up to analysis daylighting performance on Solar Window system. 3)The simulation program(ESP-r, Therm5.0, Window6.0) was used in energy performance analysis. the reference model of simulation was made up to analysis energy and daylighting performance on Solar Window system. 4)The Size of Simulation model for daylighting and heating/cooling energy analysis was $148.5m^2$ 5)The lighting performance analysis was carried out with various variants, such as the size and installed area of Solar Window system. 6)Energy performance simulation was carried out with various variants, such as Integrated U-value of Solar Window system according to its position, installed angle and insulation thickness. Consequently, When Solar Window system is equipped with balcony window of Apartment, Annual heating and cooling energy of reference model was cut down at the average of $4.1kWh/m^2$ or 4.2%.

• The Journal of Advanced Prosthodontics
• /
• v.12 no.6
• /
• pp.361-368
• /
• 2020

PURPOSE. The present study aimed to evaluate the accuracy of a desktop scanner and intraoral scanners based on the volumetric dimensions of a complete arch. MATERIALS AND METHODS. Seven reference models were fabricated based on the volumetric dimensions of complete arch (70%, 80%, 90%, 100%, 110%, 120%, and 130%). The reference models were digitized using an industrial scanner (Solutionix C500; MEDIT) for the fabrication of a computer-aided design (CAD) reference model (CRM). The reference models were digitized using three intraoral scanners (CS3600, Trios3, and i500) and one desktop scanner (E1) to fabricate a CAD test model (CTM). CRM and CTM were then superimposed using inspection software, and 3D analysis was conducted. For statistical analysis, one-way analysis of variance was used to verify the difference in accuracy based on the volumetric dimensions of the complete arch and the accuracy based on the scanners, and the differences among the groups were analyzed using the Tukey HSD test as a post-hoc test (α=.05). RESULTS. The three different scanners showed a significant difference in accuracy based on the volumetric dimensions of the complete arch (P<.05), but the desktop scanner did not show a significant difference in accuracy based on the volumetric dimensions of the complete arch (P=.808). CONCLUSION. The accuracy of the intraoral scanners was dependent on the volumetric dimensions of the complete arch, but the volumetric dimensions of the complete arch had no effect on the accuracy of the desktop scanner. Additionally, depending on the type of intraoral scanners, the accuracy differed according to the volumetric dimensions of the complete arch.

• The Korea Journal of Herbology
• /
• v.28 no.4
• /
• pp.1-6
• /
• 2013

Objectives : In other to determine the optimal extraction conditions, the various Bojungikgi-tang (BJIGT) decoctions prepared by different pressure levels and different extraction times were compared and evaluated in terms of the extract yield and the total soluble solid content. Methods : Decoctions were prepared by the pressure levels of 0 (non-pressurized) and 1 $kgf/cm^2$ (pressurized) for 60, 120 and 180 min. The extract yield and the total soluble solids content of decoctions were measured, and the amounts of the reference compounds in decoctions were investigated by the analysis using high performance liquid chromatography. Results : The extract yield and the total soluble solid content were higher in decoctions extracted by the pressurized method than those from decoction with non-pressurized method. The patterns of yield and contents showed a proportional increase to the extraction time. In analysis of the linear regression for four reference compounds such as liquiritin, nodakenin, hesperidin, and glycyrrhizin, the good linearity with the correlation coefficient more than 0.9999 was observed. The highest contents for four reference compounds were observed at 180 min of both the pressurized method and the non-pressurized method. Conclusions : This study suggests that the pressure in extraction method and the extraction time affect the compositional constituents in BJIGT decoctions. The extraction time of 180 min could be chosen in both pressurized and non-pressurized method as optimal extraction condition.