• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.3
• /
• pp.37-45
• /
• 1995

Effect of reentrant type bowl geometry on combustion characteristics was investigated in a D.I. diesel engine. The main factor was the cupola height of bowl center and the reentrant angle of combustion chamber, and the cylinder pressure, engine performance and emissions of the engine using the total 11 kinds of the combustion chamber were measured by test. The results are as follows. The NOx decreases by increasing the cupola height of bowl center because it makes the decreasing of maximum combustion pressure by the heat loss and smooth combustion from good airflow. The smoke increases by increasing the reentrant angle at high speed range of the engine, but decrease at low and medium speed range until the reentrant angle becomes $15^{\circ}$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.1
• /
• pp.46-56
• /
• 1991

In this paper, 16word X 8bit Content Addressable and Reentrant Memory(CARM) is described. This device has 4 operation modes(read, write, match, reentrant). The read and write operation of CARM is like that of static RAM, CARM has the reentrant mode operation where the on chip garbage collection is accomplished conditionally. Thus function can be used for high speed matching unit of dynamic data flow computer. And CARM also can encode matching address sequentially according to therir priority. CARM consists of 8 blocks(CAM cell, Sequential Address Encoder(S.A.E). Reentrant operation. Read/Write control circuit, Data/Mask Register, Sense Amplifier, Encoder. Decoder). Designed DARM can be used in data flow computer, pattern, inspection, table look-up, image processing. The simulation is performed using the QUICKSIM logic simulator and Pspice circuit simulator. Having hierarchical structure, the layout was done using the 3{\;}\mu\textrm{m} n well CMOS technology of the ETRI design rule.

• International Journal of Vascular Biomedical Engineering
• /
• v.3 no.1
• /
• pp.23-29
• /
• 2005

We developed a three dimensional cardiac tissue model based on human cardiac cell and mono-domain approximation for action potential propagation. The human myocyte model proposed by ten Tusscher et al. (TNNP model) (2004) for cell electrophysiology and a mono-domain method for electric wave propagation are used to simulate the cardiac tissue propagation mechanism using a finite element method. To delineate non-homogeneity across cardiac tissue layer, we used three types of cardiac cell models. Ansiotropic effect of action potential propagation is also considered in this study. In this 3D anisotropic cardiac tissue with three cell layers, we generated a reentrant wave using S1-S2 protocol. Computational results showed that the reentrant wave was affected by the anisotropic properties of the cells. To test the reentrant wave under pathological state, we simulated a hypertopic model with non-excitable fibroblasts in stochastic manner. Compared with normal tissue, the hypertropic tissue result showed another center of reentrant wave, indicating that the wave pattern can be more easily changed from regular with a concentric focus to irregular multi-focused reentrant waves in case of patients with hypertrophy.

• Journal of Chest Surgery
• /
• v.26 no.5
• /
• pp.403-408
• /
• 1993

The atrioventricular node reentrant tachycardia[AVNRT] is a common type of supraventricular tachycardias. Recently we experienced two cases of AVNRT. One is AVNRT with severe aortic regurgitation[grade IV] and the other is AVNRT with patent ductus arteriosus. Dissection of perinodal tissue has been successfully carried out in the beating heart under the normothermic cardiopulmonary bypass, and aortic valve replacement and ligation of patent ductus arteriosus were also performed, respectively. Postoperatively, permanent atrioventricular block was not occured and AVNRT was not developed during the follow up. We propose that the surgical dissection of perinodal tissue is a simple and effective treatment for the patient with refractory AVNRT.

• Journal of Chest Surgery
• /
• v.23 no.1
• /
• pp.205-212
• /
• 1990

A 17 year old female patient with Ebstein`s anomaly received surgical treatment for WPW syndrome and AV nodal reentrant supraventricular tachycardia[SVT] Electrophysiologic study revealed that an anomalous pathway was located in the right posterolateral portion and antegrade dual AV nodal pathway responsible for AV nodal reentrant tachycardia. The patient was underwent surgery on February 18, 1987. Intraoperative mapping was used to define the location of accessory pathway. The accessory pathway was cryoablated through the epicardium. Simultaneously discrete cryoablation around the perinodal area was performed to prevent AV nodal reentrant SVT. The atrialized right ventricle of Ebstein`s anomaly was plicated with 11 pledget mattress sutures under the cardiopulmonary bypass. Two and half years after surgery, the patient has no evidence of WPW syndrome or supraventricular tachycardia.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.12 no.1
• /
• pp.1-8
• /
• 1987

In this paper, resonance frequencies of a reentrant cavity are computed by the mode matching method and the mode orthogonality. The reentrant cavity is composed of a coaxial cable and a cylindrical waveguide, so that resonance frequencies of the resonator can be varied by adjusting the length of the inner conductor of a coaxial cable. The result can be applied to numerous microwave devices such as klystron, wavemeter and resonant circuits of a amplifier and to the measurement of dielectric parameters.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.221-223
• /
• 2010

Considering the similarity between fluid vortex and arrhythmogenic reentrant waves in heart, we applied the non-dimensionalization method in fluid dynamics to arrhythmia analysis and discovered a new non-dimensional simulation results, there was a threshold value of the number that resulted in the induction of a reentrant wave.

• Journal of the Korea Society for Simulation
• /
• v.25 no.1
• /
• pp.45-52
• /
• 2016

In this study, we consider a capacity planning problem of reentrant hybrid flowshops. High-tech electronic products such as semiconductor or TFT-LCD, are produced from manufacturing systems which can be considered as reentrant hybrid flowshops. In the considered capacity planning problem, we determine the number of machines at each stage in the manufacturing system. We introduce criteria indicating which stage needs additional machines or which stage needs reduction of machines considering the characteristics of the product types and the manufacturing system. The objective function of the problem is maximizing throughput rate of the system, of which values are obtained from the simulation model depicting the hybrid flowshops. The performance of the proposed methods were evaluated through a series of computational experiments. The simulation model was also used for conducting the comparison experiments among the proposed method and benchmarks.

• Industrial Engineering and Management Systems
• /
• v.12 no.4
• /
• pp.306-316
• /
• 2013

The semiconductor industry has grown rapidly, and subsequently production planning problems have raised many important research issues. The reentrant flow-shop (RFS) scheduling problem with time windows constraint for harddisk devices (HDD) manufacturing is one such problem of the expanded semiconductor industry. The RFS scheduling problem with the objective of minimizing the makespan of jobs is considered. Meeting this objective is directly related to maximizing the system throughput which is the most important of HDD industry requirements. Moreover, most manufacturing systems have to handle the quality of semiconductor material. The time windows constraint in the manufacturing system must then be considered. In this paper, we propose a hybrid genetic algorithm (HGA) for improving chromosomes/offspring by checking and repairing time window constraint and improving offspring by left-shift routines as a local search algorithm to solve effectively the RFS scheduling problem with time windows constraint. Numerical experiments on several problems show that the proposed HGA approach has higher search capability to improve quality of solutions.

• Journal of ILASS-Korea
• /
• v.1 no.4
• /
• pp.54-62
• /
• 1996

Effect of reentrant type bowl geometry on combustion characteristics was investigated in a D.1.diesel engine. The main factor was the aspect ratio (Bowl Diameter/Bowl Depth) of bowl of combustion chamber, and the measured data include the cylinder pressure, engine performance and emissions of the engine using the 4 kinds of the combustion chamber. Experimental results indicate that the effect of dc/H and nozzle protrusion are relatively small and there exists an optimum dc/H according to the combustion conditions. It is also found that the smoke emission is quite sensitive the overall combustion time where the 90 percentage of the combustion heat is released. The smoke mission increases by shortening the 90% combustion time while it decreases by delaying the 90% combustion time.