• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.817-818
• /
• 2008

• Korean Journal of Metals and Materials
• /
• v.47 no.10
• /
• pp.667-674
• /
• 2009

High temperature wear of STD 61 tool steels sliding against the Al-9%Si coated steels used for hot press forming has been studied in comparison with that of the tool steels sliding against the uncoated steels. Wear tests have been performed using a pin-on-disc configuration under an applied normal load of 50N for 20 min with heating the coated and uncoated steels up to 800$^{\circ}C$. It was found on the worn surface of the STD 61 tool steels sliding against the Al-9%Si coated steels that the formation of the glazed layers containing Al transferred from the coated tribopair may contribute to a reduction of the coefficient of friction, and detachment in part occur due to delamination wear, resulting in higher specific wear rate. On the other hand the Fe-oxide wear debris entrapped on the softer surface of the uncoated steels can act as a tribosurface, leading to decreased adhesive wear of the STD 61 tool steels, resulting in a lower specific wear rate.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.11
• /
• pp.106-113
• /
• 1996

Using stainless steel as the cold forged parts especially the outer parts of automobile is gradually increasing because it can bear up against the erosion and the wear. During cold forging of the stainless steel the working pressure acting on die surface are very high therefore the wear on die surface can be greatly increased. In cold forging processes, die failure must be considered before die design. One of the main reasons of die failure in industrial application of metal forming technologies is wear. The die wear affects the tolerances of forged parts, metal flow and costs of processes etc. The only way to to control these failures is to develop methods which allow prediction of the die wear and which are suited to be used in the desing stage in order to optimize the process. In this paper, the rigid-plastic finite element method was combined with the wear prediction routine and then the forward extrusion process using stainless steel was analysed simultaneously. To minimize the die wear the FPS algorithm was applied and the optimal conditions of die configuration are suggested.

• Tribology and Lubricants
• /
• v.40 no.3
• /
• pp.78-83
• /
• 2024

The development of eco-friendly alternative energy sources has become a global priority owing to the depletion of fossil fuels and an increase in environmental concerns. Hydrogen energy has emerged as a promising clean energy source, and hydrogen compressors play a crucial role in the storage and distribution of compressed hydrogen. However, harsh operating conditions lead to the rapid deterioration of conventional lubricants in hydrogen compressors, thereby necessitating the development of advanced lubrication technologies. This study introduces micrometer-sized silicone rubber powders as lubricant additives to enhance the lubrication performance of hydraulic oils in hydrogen compressors. We prepare silicone rubber powders by varying the ratio of the silicone rubber base to the curing agent and investigate their effects on interfacial properties, friction behavior, and wear characteristics. The findings reveal that the incorporation of silicone rubber powders positively influences the surface affinity, wettability, friction reduction, and wear resistance of the lubricants on the 304SS substrate. Moreover, we identify the optimal lubricant formulations, with a 15:1 ratio demonstrating the most effective friction reduction and a 5:1 ratio exhibiting the highest wear resistance. The controlled surface modification by the silicone rubber powder and the enhanced interfacial characteristics of the powder-containing lubricants synergistically contribute to the improved lubrication performance. These results indicate the potential of silicone rubber powder additives for the development of long-life lubrication solutions for hydrogen compressors and related applications, ultimately contributing to the advancement of sustainable energy technologies.

• Journal of Korea Foundry Society
• /
• v.42 no.3
• /
• pp.191-197
• /
• 2022

This study aims to improve the machinability of gray cast irons in high speed cutting by using nonmetallic inclusions. In this research, small quantities of AL and Mg were added to conventional gray cast irons without influencing their mechanical characteristics and castability to investigate the effects of these nonmetallic inclusions in the gray cast irons on tool wear in high speed cutting. During the high speed turning of gray cast iron containing Al and Mg using a cermet tool, protective layers consisting of Al, Mg, Si, Mn, S and O were detected on the flank face and rake face of the tool, and flank and crater wear were significantly reduced compared to the turning of conventional gray cast iron and gray cast iron added with Al. The effect of inclusions on tool wear increased with increasing cutting speed, and flank and crater wear was the smallest at the cutting speed of 700m/min. Moreover, in face milling, the addition of Al and Mg drastically decreased the wear rate, and wear hardly progressed even in prolonged cutting length after initial wear. The amount of adhesion on tool faces increased as the cutting speed increased. This increase in cutting speed resulted in the formation of a thick protective layer and the reduction of tool wear. Furthermore, the addition of small amounts of Al and Mg prevented thermal cracks in the face milling of gray cast irons.

• Tribology and Lubricants
• /
• v.6 no.1
• /
• pp.116-125
• /
• 1990

An experimental programme was established to determine the wear behaviour of TiN coatings of thickness 1 $\mu$m and 3 $\mu$m. by PECVD with the variation of applied load, sliding velocity and sliding distance. It was shown that oxidation of transferred metal as sliding speed increased formed oxide film so that it contributed in decreasing the wear rate. With the roller-on-disc tribometer employed, the wear rate of the roller specimen was decreased with the increase in sliding distance due to the reduction in effective contact pressure. Finally, the severe cracks concentrated at the trailing edge of contact surface were explained in terms of high tensile stress prevailing at the trailing edge of the contact and were identified as a dominant wear mechanism as well as the strong local welding between coating layer and the counter surface, leading to the debonding of the coating layer.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.1
• /
• pp.53-59
• /
• 2011

End milling is available for machining the various shape of products and has been widely applied in many manufacturing industries. The quality of products depends on a machine tool performance and machining conditions. Recognition characteristics of the cutting condition is becoming a critical requirement for improving the utilization and flexibility of present-day CNC machine tools. The measurement of tool wear would be performed by coordinate-measuring machine(CMM). However, the usage of CMM requires much time and cost. In order to overcome the difficulties, on-line measurement(OLM) system was applied for a tool wear measurement. This study shows a reliable technique for the reduction of machining error components by developing a system using a CCD camera and machine vision to be able to precisely measure the size of tool wear in flat end milling for CNC machining. The CCD camera and machine vision attached to a CNC machine can determine tool wear quickly and easily.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.71-77
• /
• 2007

The surface of railway wheel tread in wheel-rail system can not be free from wear because of various circumstance such as railway condition, maintenance condition, weather condition, characteristics of wheel surface's geometrical shape, and vehicle suspension's structural characteristics etc. Therefore, the research on wear reduction and maintenance method are very important to ensure the safety of railway vehicle, to improve car comfort and to decrease maintenance cost. In this study, the wear rates of railway wheel have been periodically measured in terms of the running distance of Electrical Multiple Unit which have been currently operated and the microstructure transformation of wheel tread using replication method have been performed. The results show that the relations between the flange wear and tread microstructure are depended on running distance and it will supply basic data on wheel maintenance.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.298-303
• /
• 2000

The 3 mol% yttria stabilized zirconia (3-Y PSZ) powder was heat treated at 50 0$^{\circ}C$ to evaporate the polymer binder and stabilize the tetragonal phase. The wear experiments were carried out on a ring-on-plate type reciprocating wear tester at selected temperatures with in the range room temperature to 600$^{\circ}C$ The results show that the heat treatment of powder decreases the wear rate due to the reduction of microcracks and pores in coatings and the stabilization of the tetragonal phase. Powder heat treatment enhanced the quality of the coating layer by removing remnant gases during coating process and the powder heat treatment at which tetragonal phase is stable diminished phase ratio of monoclinic. These two effects improved wear resistance characters.

• International Journal of Railway
• /
• v.7 no.3
• /
• pp.65-70
• /
• 2014

In this paper, the reduction effect of dry (solid) lubrication on wheel flange wear rates is studied. The solid / dry lubricator systems were attached to the most front and furthest back axles of a coach in order to examine the wear behavior of the equipped wheels. An attempt is also made to make a comparison between wear behaviors of these wheel flanges having dry lubrication devices with non-lubricated wheels in other railcars. Finally, a comparison is made between life-cycle of wheels under investigation and other similar wheel types.