• International Journal of High-Rise Buildings
• /
• v.11 no.3
• /
• pp.207-219
• /
• 2022

During the structural design of urban over-track high-rise buildings, two problems are most likely encountered: the abrupt change of story stiffness between the podium and the upper towers, as well as the demand for train-induced vibration control. Traditional earthquake-resistant structures have to be particularly designed with transfer stories to meet the requirement of seismic control under earthquakes, and thus horizontal seismic isolation techniques are recommended to solve the transfer problem. The function of mitigating the vertical subway-induced vibration can be integrated into the isolation system including thick rubber bearings and 3D composite vibration control devices. Engineering project cases are presented in this paper for a more comprehensive understanding of the engineering practice and research frontiers of urban over-track high-rise buildings in China.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.4
• /
• pp.848-852
• /
• 2007

Many numerical analysis tools for predicting penetration speed of sheet pile are thought to be unreliable because they overestimate penetration speed for shallow depth of penetration. In order to overcome the defects of numerical analysis, lateral vibration model of sheet pile was suggested and energy consumption due to lateral vibration of sheet pile was estimated. Also, load reduction factor which explains reduction of vibratory driving force due to lateral vibration was introduced.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.166-170
• /
• 2008

In this study, it proved that transfer path analysis is a proper technique to estimate the interior noise from comparing measured interior noise in case of 3 point supported engine mount system. And the simulation of the vibration isolation for active engine mount using FXLMS algorithm is performed. Also, it verified that reduction of estimated interior noise from transfer path analysis and simulation of the vibration isolation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.135-140
• /
• 2013

This paper deals with noise reduction on a light source driving board in a projector. We analyze causes of noise/vibration in the circuit with the present increasing use of LD and LED driving boards. The main source of noise is the MLCC in the driving board. Our aim is to investigate how the mechanical arrangement of the circuit elements affects noise reduction. The result of our experiment shows that noise can be reduced by symmetrical arrangement and slots in PCB. This result is expected to facilitate a variety of applications for manufactures without a need to change circuit elements.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.255-258
• /
• 2005

Recently, demands for the reduction of noise generated by transformers have been increasing. Almost all the noise generated by a transformer is a result of magnetostrictive vibration in the core. The noise radiates into the atmosphere from the tank through the insulation oil. One method of reduction such a noise is to build a free-standing enclosure of concrete and steel plates around the transformer. However, this method has some disadvantages, for example, a large area is needed for equipment installation. In this paper, the vibration and noise effects which is transferred from reinforce channel to insulation panel generated by transformer have been identified for the several kinds of insulation panel shape and damping sheet experimentally.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.04a
• /
• pp.381-385
• /
• 2014

This paper investigates the magneto-rheological(MR) mount for the marine diesel-generator(D/G) sets. Sometimes, significant vibrations over the allowable limit are observed on the D/G sets due to their huge excitation forces. Because the severe vibration can lead to structural damages to the D/G sets, it should be reduced below the limit. Although passive mounts with rubber isolators are usually used, the vibration reduction performance is not always sufficient. In addition, expecting that the vibration levels required by customers will get more severe, vibration reduction devices need to be developed. To the aim, the flow mode type of MR mount has been designed. Especially, the annular-radial configuration was adopted to enhance the damping force within the restricted space. The geometry of the mount has been optimized to obtain the required damping force and the magnetic field analysis has been carried out using ANSYS APDL. To verify the performance of the developed MR mount, an excitation test was conducted. In addition, they were applied to a medium-speed diesel generator and it was verified that about 40% of vibration reduction was yielded.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.6
• /
• pp.582-587
• /
• 2012

This paper presents a solution of the vibration reduction in the hollow shafts by using magentorehological( MR) elastomer. Proposed active damping structure is built by embedding the MR elastomers whose elastic modulus is controllable by an applied magnetic field. MR elastomers consist of synthetic rubber filled with micron-sized magnetizable particles. For reduction of vibration, dynamic damper of hollow shaft is designed by using MR elastomer and equipped in the hollow shaft for the application to drive shaft. Experiment results are shown through the experiments to confirm the effect of MR elastomer dynamic damper for vibration reduction. Thus, the designed damping structure can be applied to vibration absorber used in drive shafts as well as the propeller shafts.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.124-127
• /
• 2006

In this paper, noise and vibration reduction of double-resiliently mounted pump-like machinery is studied. SBN(Structure-borne noise) reduction through upper and lower mount is analyzed by assuming that the system is modeled as a mass-spring system. In addition, the impedance of the floor is included in the prediction. The comparison of the SBN difference through upper mount show that the effect of impedance is negligible, while the measurement differs significantly from the prediction for high frequency range. It is found that the assumption of point mass-spring system leads to the disagreement between prediction and measurements.

• Journal of KSNVE
• /
• v.9 no.4
• /
• pp.730-737
• /
• 1999

This paper illustrates the sound vibration phenomenon of mono type TV set produced by spearker and suggests guidelines for reducing the noise induced by the sound vibrations. In order to illustrate the sound vibration phenomenon, the structural acoustic coupled analysis for the grill and cavity of speaker and structural analysis for main frame are performed. To veify the structural analysis results, experimental modal test is carried out. It is found that the acoustic excitation in the cavity is negligible and main sound vibrations occur near the bottom of TV set. An improved model is found by doing structural modifications based on structural analysis and sound vibration tests are performed to verify the validation of the improved model. The obtained results are applied to similar models and design guide lines for noise reduction are suggested.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.372-377
• /
• 2004

Tilting bogie system allow the train to pass curve at higher speed without affecting passenger comfort. As the tilting trains offer the optimum means of providing faster and more comfortable rail service with minimum of environmental disturbance and capital investment, mere than 14 countries have now adopted or are about to adopt tilting train technology. The Korean National Railroad is also planing to apply faster tilting train to the areas where the High speed rail service are not provided. This paper describes the parametric study to achieve the optimal suspension parameters of the Bogie for 180 km/h Korean Tilting Train(TTX) from the view point of the vertical and lateral vibration reduction.