• Transactions of Materials Processing
• /
• v.18 no.5
• /
• pp.410-415
• /
• 2009

Experimental and numerical studies were performed to examine the effect of material temperature and reduction ratio on friction coefficient during hot flat rolling. We carried out a single pass pilot hot flat rolling test at the temperatures range of $900{\sim}1200^{\circ}C$ and measured the spread of deformed material while reduction ratio varied from 20% to 40%. Materials used in this study were a high carbon steel and two alloy steels. The dimension of specimen used in hot rolling experiment was $50mm{\times}50mm{\times}300mm$. We performed a series of finite element simulation of the hot rolling process to compute the friction coefficient change in terms of steel grade and reduction ratio. Results showed that temperature dependency of friction coefficient is not noteworthy but the effect of reduction ratio on friction coefficient is quite large. For high carbon steel, friction coefficient at reduction ratio of 30% is lower than that at that of 20%. Meanwhile friction coefficient at reduction ratio of 40% was one and half times large compared with that at that of 20%. The effect of steel grade on friction coefficient was significant when reduction ration was large, e.g., 40%.

• Tribology and Lubricants
• /
• v.38 no.6
• /
• pp.261-266
• /
• 2022

Notably, laser surface patterning facilitates tribological applications under lubricated sliding contacts. Consequently, a special pattern that can reduce the coefficient of friction under contact is considered necessary for improved machine efficiency. However, inappropriate pattern designs produce higher friction coefficients and cannot reduce friction. In this study, we use cast iron pins as specimens to investigate their friction and wear characteristics. Moreover, we experimentally investigate the correlation between the friction reduction effect and the design of groove crosshatch patterns fabricated with various angles and widths. We conduct a friction test using a pin-on-disc type tribometer under grease lubrication to study the friction reduction effect of the specimens, and we observe that the average coefficient of friction changes with the crosshatch angle and width. The experiment reveals that grooved crosshatch specimens with a crosshatch angle of 135°maximize friction reduction. The coefficient of friction of the groove specimens with a width of 120 ㎛ is lower than that of the specimens with a width of 200?. The friction reduction effect of the width of the groove is attributed to the density of the groove pattern. Thus, grooved crosshatch patterns can be designed to maximize friction reduction, and the friction property of a grooved crosshatch pattern is found to be related to its width and angle.

• Tribology and Lubricants
• /
• v.20 no.5
• /
• pp.266-271
• /
• 2004

The aim of this paper is to investigate the effect of surface texturing on reduction friction and to understand the potential of friction reduction through micro-scale dimple to fabricate by photolithography on pin-on-disk test using flat-on-flat contact geometry. It was verify that the friction property with respect to the same pitch has been influence on the size of dimple under lubricated sliding contact. Also, we can recognize from Stribeck curve that the friction property has a connection with the size of dimple. It can explain a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. The friction property has been an effect on the size of surface texture on reduction friction, not only because the density of dimple, but also because the ratio of diameter/pitch. This ratio of approximately 0.5 recommend under the tested friction condition. It suggested that the ratio of d/p is an important parameter for surface texture design.

• Journal of the Society of Naval Architects of Korea
• /
• v.40 no.3
• /
• pp.9-15
• /
• 2003

An experimental study has been carried out as a basic research for development of the friction drag reduction technology for ships by polymer injection. Experimental apparatus and procedures have been devised and prepared to measure the changes of the wall friction with injection of a polymer solution and basic experimental data on the friction drag reduction are obtained for a turbulent fiat-plate boundary layer and fully-developed channel flows. Variations of the friction drag reduction with some important parameters of polymer injection, such as the concentration of polymer solution, its injection flow rate and the measuring position downstream from the injection slot, are also investigated. Important experimental data and results obtained in the present study are presented. The amount of friction drag reduction up to 50% is observed.

• Transactions of Materials Processing
• /
• v.20 no.3
• /
• pp.243-249
• /
• 2011

In this study, an approach designed to compute high temperature friction coefficients for SCM 435 steel through a pilot hot rolling test and a finite element analysis, is proposed. Single pass pilot hot flat rolling tests with reduction ratios varying from 20 to 40% were carried out at temperatures ranging from 900 to $1200^{\circ}C$. In the proposed approach, the friction coefficient is calculated by comparing the measured strip spread and the roll force with the simulation results. This study showed that the temperature and reduction ratio had a significant influence on the friction coefficient. As both material temperature and reduction ratio become higher, the friction coefficient increases monotonically. This finding is not in agreement with the Ekelund model, which is widely used in the analysis of the hot rolling process. In the present work, the friction coefficient at a reduction ratio of 40% was found to be 1.2 times greater than that at a reduction of 30%. This higher friction coefficient means that an increment of the roll thrust force is expected at the next stand. Therefore, a roll pass designer must understand this phenomenon in order to adjust the reduction ratio at the stands while keeping the driving power, the roll housing structure and the work roll strength within the allowable range.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.217-222
• /
• 2004

The aim of this paper is to investigate the effect of micro-dimple size on reduction friction and to understand the potential of friction reduction through micro-scale dimple to fabricate by photolithography on pin-on-disk test using flat-on-flat contact geometry. It was verify that the friction property with respect to the same pitch has been influence on the size of dimple under lubricated sliding contact. Also, we can recognize from Stribeck curve that the friction property has a connection with the size of dimple. It can explain a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. The friction property has been an effect on the size of surface texture on reduction friction, not only because the density of dimple, but also because the ratio of diameter/pitch. This ratio of approximately 0.5 is recommend under the tested friction condition. It suggested that the ratio of d/p is an important parameter for surface texture design.

• Journal of the Society of Naval Architects of Korea
• /
• v.40 no.3
• /
• pp.1-8
• /
• 2003

For the experiment of the friction drag reduction by microbubble injection, a drag reduction water tunnel was specifically designed and made. Experimental apparatus and procedures were devised and developed for measuring the change of wall friction drag with microbubble injection. For fully-developed channel flows. the change of friction drag with important parameters of microbubble injection is investigated and the experimental data and results obtained are presented. The amount of friction drag reduction up to 25% is observed in the present study.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.17-24
• /
• 2004

Surrface texturing of tribological application is another attractive technology of friction reducing. Also, reduction of friction is therefore considered to be a necessary requirement for improved efficiency of machine. In this paper attempts to investigate the effect of density for micro-scale dimple pattern using photolithography on bearing steel flat mated with pin-on-disk. We demonstrated the lubrication mechanism for a Stribeck curve, which has a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. It is found that friction coefficient is depended on the density of surface pattern. It was thus verified that micro-scale dimple could affect the friction reduction considerably under mixed and hydrodynamic lubrication conditions from based on friction map. Lubrication condition regime has an influence on the friction coefficient induced the density of micro dimple.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.483-486
• /
• 2002

Injection of microbubbles and/or polymer solution has been known to be a promising method for the reduction of frictional drag of water-borne vehicles. Naval Architects have been interested in friction drag reduction technology, since the friction drag of a commercial ship can be over $70{\%}$ of total resistance. The reduction of friction drag is also important for autonomous underwater vehicles and naval submarines to improve their durability and survivability In this study two sets of experiments were carried out for the friction drag reduction of 2-D channel wall and flat plate in the circulating water channels in Chungnam National University. Preliminary results from the experiments are presented and discussed.

• Tribology and Lubricants
• /
• v.25 no.5
• /
• pp.348-358
• /
• 2009

To satisfy the more severe emission regulation and the demand of higher fuel economy in near future, the combustion pressure and power output of engines is going to be higher. In order to get the reduction of engine emission and the higher power, it is needed the reduction of the tension and width of ring pack. The lower tension ring and the manufacturing technology of cast iron thinner width ring can bring the friction reduction between the ring and liner during engine running. Therfore, the fuel economy can be achieved. Thereafter the engine emission can be reduced. In this study, by using a developed basic computer program that predicts the inter-ring pressure, the motion of ring and the inter-ring pressure through a crevice volume model between adjacent rings, and the oil film thickness and the friction computed by lubrication theories, it is to be examined the effect of friction reduction from piston ring pack equipped with thinner width ring and lower tension ring.