• Journal of the Korea Concrete Institute
• /
• v.20 no.3
• /
• pp.325-333
• /
• 2008

This study evaluated the mechanical performance, shrinkage crack and fire resistance of hybrid fiber (blended steel and polypropylene fiber with different diameter and length) reinforced concrete at elevated temperature. The compressive, splitting tensile, flexural, plastic shrinkage test were conducted to the evaluate the mechanical properties and the resistance of shrinkage crack. Also, the surface investigation, reduction rate of mass and residual compressive test were performed to evaluate the physical and mechanical properties after 400$^{\circ}C$, 600$^{\circ}C$, 800$^{\circ}C$ and 1,200$^{\circ}C$ exposure. Test results showed that the hybrid fiber reinforced concrete improved the mechanical performance, shrinkage crack and fire resistance. The reduction of performance with a temperature change were high at the temperature of $600\sim800^{\circ}C$.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.1
• /
• pp.25-34
• /
• 2010

Fretting damage reduces fatigue life of the material due to low amplitude cyclic sliding and changes in the contact surfaces of strongly connected machine and structures such as bolt, key, fixed rivet and connected shaft, which have relative slip of repeatedly very low frequency amplitude. In this study, the fretting fatigue behavior of 7050-T7451 aluminum alloys used mainly in aircraft and automobile industry were evaluated. The plain fatigue test and fretting fatigue test under cyclic bending load carried out commercial bending fatigue tester and specially devised equipments to cause fretting damage. From these experimental work, the following results obtained: (1) The plain fatigue limit for stress ratio R=-l was about 151MPa. (2) In case of fretting fatigue, fatigue limit for stress ratio R=-l about 72MPa, the fatigue limit for R=0 about 81MPa, and the fatigue limit for R=0.3 about 93MPa. (3) The fatigue limit reduction rates by the fretting damage were about 52%(R=-1), 46%(R=0) and 38%(R=0.3) respectively. (4) The fatigue limit reduction rate decreased with stress ratio increase. In fretting bending test, as stress ratio increased, occurrence of initial oblique crack by fretting decreased or phased out, so that fracture surfaces were formed by plain fatigue crack occurrence, and such tendency was notable as stress amplitude increased. (5) Tire tracks and rubbed scars were observed in the fracture surface and contacted surface.

• Asian-Australasian Journal of Animal Sciences
• /
• v.8 no.5
• /
• pp.495-498
• /
• 1995

Records taken on 372 young beef bulls tested at the Ellerslie Bull Test Station, Alberta, Canada from November 1981 to April 1987 were analyzed to quantify the effects of age of dam, on-test age, on-test liveweight and herd of origin of bull on feed efficiency (feed/gain, kg/kg) in the test period (n = 231) and ultrasonic measurement of bakcfat thickness (mm) at the end of the test (n = 372). The reduction in $R^2$ due to each influencing factor (i.e. the variation accounted for by the factor) was used to indicate the importance of the influencing factor. Age of dam and on-test age of bull were not important factors on feed/gain and ultrasonic backfat thickness, as they accounted for less than 0.5% of the variation in feed/gain and ultrasonic backfat thickness, respectively (p > 0.1). On-test liveweight had some influence on feed/gain and ultrasonic backfat thickness, accounting for 3.5% (p < 0.01) and 0.4% (p < 0.05) of the total variation, respectively. The regression coefficients of feed/gain and ultrasonic backfat thickness on on-test liveweight were 0.016 (kg/kg)/kg and .013 mm/kg, respectively, both being significant (p < 0.05), indicating that lighter bulls entering the test were generally more efficient in feed utilization in the test period and had less backfat at the end of the test than heavier entering bulls. Herd of origin of bull accounted for a substantial amount of the total variation (> 16%) in feed/gain and ultrasonic backfat thickness (p = 0.08), indicating that a prolonged aqjustment period was needed to reduce the influence of herd of origin when assessing aggregate genetic merit of beef bulls for growth rate, feed efficiency and lean meat production using a central station performance testing program.

• Journal of Oriental Neuropsychiatry
• /
• v.21 no.2
• /
• pp.87-101
• /
• 2010

Objectives : The aim of this experiment was to investigate the influences of Autonomic Nervous System and EEG by conducting Reinforcement-Reduction(補瀉) acupuncture stimulation to compare the changes in acupoints on the body before and after treatment of acupuncture at Xingjian(LR2) being referred as Fire-point(火穴) and Ququan(LR8) being referred as Water-point(水穴) of Yin Liver Meridian(足厥陰肝經). Methods : This study was carried out on 30 healthy female volunteers in their 20's. There were four tests conducted throughout and the period for each test was between 2 to 5days. HRV and EEG were measured for 5 minutes before acupuncture stimulation was conducted on LR2-Reinforcement, LR2-Reduction, LR8-Reinforcement and LR8-Reduction at random. During the 20 minutes of acupuncture treatment, same subjects were measured simultaneously to observe any significant changes in acupoints. Again, the same subjects were measured for 5 minutes after removing the acupuncture in order to perform a comparative analysis. Results : The measurement of HRV showed that LF, LFnorm and LF/HF ratio increased significantly(p<0.05) while HF, HF norm decreased significantly in case of LR2-Reinforcement & LR8-Reduction. Both LR2-Reduction and LR8-Reinforcement induced a significant increase in HFnorm. EEG measurement indicated low $\alpha$ wave decreased and high $\beta$ wave increased significantly at LR2-Reinforcement during post-acupuncture period compared with acupuncture stimulation period. Both LR2-Reduction and LR8-Reinforcement developed significantly low $\alpha$ wave and high $\alpha$ wave. High $\beta$ wave increased significantly at LR8-Reduction during the acupuncture stimulation in comparison with pre-acupuncture period. Conclusions : The manipulation of acupuncture stimulation at LR2-Reinforcement and LR8-Reduction enhanced the activity of sympathetic nerves and the state of arousal while that of para sympathetic nerves declined. On the other hand, LR2-Reduction and LR8-Reinforcement developed the levels of para sympathetic nerves and relaxation.

• Journal of Biosystems Engineering
• /
• v.42 no.1
• /
• pp.1-11
• /
• 2017

Purpose: Methods: Three-dimensional CFD modeling was conducted to analyze the flow structure and discharge flow rate corresponding to the variation in the geometry of the flow channel in a microtube. Additionally, experiments were carried out, and the discharge flow rate was measured at various inlet pressures and inclination angles of the microtube. Results: The quantitative data of velocity distribution and discharge flow rate were obtained. As the width and length of the microtip increased, the discharge flow rate decreased significantly because of the increase in the loss of pressure along the microtube. As the depth of the microtip increased, the flow rate also increased because of the reduction in the flow resistance. However, in this analysis, the variation in the angle of the microtip did not influence the flow rate. From the experimental results, it was observed that the flow rate increased linearly with the increase in the inlet pressure, and the effects of the inclination angle were not clearly observed in those test cases. The values of the flow rate obtained from the experiments were significantly lower than that obtained from the CFD analysis. This is because of the distortion of the shape of the flow path inside the microtube during the fabrication process. The distortion of the flow path might decrease the flow cross-sectional area, and it would increase the flow resistance inside the microtube. The variation in the flow rate corresponding to the variation in the inlet pressure showed similar trends. Conclusions: Therefore, the results of the numerical analysis obtained from this study can be efficiently utilized for optimizing the shape of the microtip inside a microtube.

• International journal of advanced smart convergence
• /
• v.12 no.4
• /
• pp.386-394
• /
• 2023

This study investigated changes in salivary cortisol, lactic acid, and heart rate along the route during walking exercise in a forest environment for the purpose of reducing stress. Walking exercise in a forest environment was conducted on a Hill Type (Distance: 800m, Average slope 25°, Altitude 112m) and Step Type (Distance: 800m, Average slope 25°, Altitude 114m) routes for 10 female college students in their 20s. The subjects were asked to walk at a speed of 60 bpm. The resulting changes in salivary cortisol, lactate, and average heart rate during exercise were compared and analyzed using Repeated Measurement two-way ANOVA, and the maximum heart rate during exercise and average heart rate at rest were compared and analyzed using paired t-test, and the following results were obtained. First, there was no significant difference in salivary cortisol depending on the type and period of the forest, but it tended to gradually decrease. Second, there was a significant difference in lactic acid depending on the type and period, and it was higher in Step Type. Third, there was a significant difference in the average heart rate during exercise, and it was higher in Step Type. Fourth, there was a significant difference in maximum heart rate during exercise, and it was higher in Step Type. Fifth, there was no significant difference in average heart rate during rest. In summary, walking exercise in a forest environment can be effective for stress reduction for female college students in their 20s, but it appears that forest routes should be selected according to physical strength level, and walking exercise in a forest environment for long periods of time is not recommended. For this purpose, it is suggested that it is appropriate to select the Hill Type route.

• Journal of Broadcast Engineering
• /
• v.24 no.6
• /
• pp.1035-1052
• /
• 2019

Recently, as the demand for immersive videos increases, efficient video processing techniques for omnidirectional immersive video is actively developed by MPEG-I. While the omnidirectional video provides a larger degree of freedom for a free viewpoint, the size of the video increases significantly. Furthermore, in order to compress 6 degree-of-freedom (6 DoF) videos that support motion parallax, it is required to develop a codec to yield better coding efficiency. In this paper, we develop a 6 DoF codec using Versatile Video Coding (VVC) as the next generation video coding standard. To the authors' best knowledge, this is the first VVC-based 6 DoF video codec toward the future ISO/IEC 23090 Part 7 (Metadata for Immersive Media (Video)) MPEG-I standardization. The experiments were conducted on the seven test video sequences specified in Common Test Condition (CTC) in two operation modes of TMIV (Test Model for Immersive Media) software. It is demonstrated that the proposed codec improves coding performance around 33.8% BD-rate reduction in the MIV (Metadata for Immersive Video) mode and 30.2% BD-rate reduction in the MIV view mode as compared to the state-of-the-art TMIV reference software. We also show the performance comparisons using Immersive Video PSNR (IV-PSNR) and Mean Structural Similarity (MSSIM).

• Journal of the Korea Society of Computer and Information
• /
• v.18 no.12
• /
• pp.197-205
• /
• 2013

In this study, we developed a program of optimizing stand-level carbon stock using a stand-level yield model and the Simulated Annealing (SA) heuristic method to derive a optimized forest treatment solution. The SA is one of the heuristic algorithms that can provide a desirable management solution when dealing with various management purposes. The SA heuristic algorithm applied 'thermal equilibrium test', a thresholds approach to solve the phenomenon that does not find an optimum solution and stays at a local optimum value during the process. We conducted a sensitivity test for the temperature reduction rate, the major parameter of the thermal equilibrium test, to analyze its influence on the objective function value and the total iteration of the optimization process. Using the developed program, three scenarios were compared: a common treatment in forestry (baseline), the optimized solution of maximizing the amount of harvest(alternative 1), and the optimized solution of maximizing the amount of carbon stocks(alternative 2). As the results, we found that the alternative 1 showed provide acceptable solutions for the objectives. From the sensitivity test, we found that the objective function value and the total iteration of the process can be significantly influenced by the temperature reduction rate. The developed program will be practically used for optimizing stand-level carbon stock and developing optimized treatment solutions.

• International Journal of Automotive Technology
• /
• v.7 no.4
• /
• pp.485-492
• /
• 2006

The AA5182/polypropylene/AA5182(AA/PP/AA) sandwich sheets have been developed for application to automotive body panels in future lightweight vehicles with significant weight reduction. It has been reported that the AA5182 aluminum sheet shows $L\"{u}ders$ band because of dissolved Mg atoms that cause fabrication process problem, especially surface roughness. The examination of serration behavior has been made after the tensile deformation of the AA/PP/AA sandwich sheets as well as that of the AA5182 aluminum skins at room and elevated temperatures. All sandwich sheets and the AA5182 aluminum skin showed serration behavior on their flow curves. However, the magnitude of serration was significantly diminished in the sandwich sheet with high volume fraction of the polypropylene core. According to the results of the analysis of the surface roughness following the tensile test, $L\"{u}ders$ band depth of the sandwich sheet evidently showed lower than that of the AA5182 aluminum skin. The strain rate sensitivity, m-value, of the AA5182 aluminum skin was -0.006. By attaching these skins to the polypropylene core, which has relatively large positive value of 0.050, m-value of the sandwich sheets changed to the positive value. The serration mechanism of the sandwich sheets was quantitatively investigated in the point of the effect on polypropylene thickness variation, that on the strain rate sensitivity and that on the localized stress state.

• Journal of Biosystems Engineering
• /
• v.33 no.6
• /
• pp.390-395
• /
• 2008

Current high oil price and the agreement on global climate change prevention have increased worldwide investment and research on renewable energy. In Korea, development of a rapeseed dryer for bio-diesel production has been started in 2007. Usually, rapeseeds are harvested in early summer, because rice cultivation is followed right after rapeseed harvesting. Early harvest and bad summer results in highly moistured rapeseed and development of artificial drying system is required to dry great amount of rapeseed that couldn't be processed by sun drying alone. The rapeseed dryer was modified from an existing circulation type grain dryer. Modification of the dryer was performed with the aid of CFD simulation. Drying test showed that drying rate of rapeseed was 1.51%/h and germination rate reduction was 4.5%p for the drying temperature of $60^{\circ}C$.