• Journal of Biomedical Engineering Research
• /
• v.35 no.5
• /
• pp.125-131
• /
• 2014

The purpose of this study is to verify the utility of reflected photoplethysmography sensor using two green light emitting diodes that influenced by ambient light. Recently it has been studied that green light emitting diode is suitable for light source of reflected photoplethysmography sensor at low temperature and high temperature. Another study showed that, green light is better for monitoring heart rate during motion than led light. However, it has a bad characteristic about ambient light noise. To verify the utility of reflected photoplethysmography sensor using green light emitting diode, this study measures the photoplethysmography signal that is distorted by ambient light and will propose a solution. This study has two parts of research method. One is measurement system that composed sensor and board. The sensor is made up PE-foam and Non-woven fabric for flexible sensor. The photoplethysmography signal is measured by measurement board that composed high-pass filter, low-pass filter and amplifier. Ambient light source is light bulb and white light emitting diode that has three steps brightness. Photoplethysmography signal is measured with lead II electrocardiography signal at the same time and it is measured at the finger and radial artery for 1 minute, 1000 Hz sampling rate. The lead II electrocardiography signal is a standard signal for heart rate and photoplethysmography signal that measured at the finger is a standard signal for waveform. The test is repeated 3 times using three sensor. The data is processed by MATLAB to verify the utility by comparing the correlation coefficient score and heart rate. The photoplethysmography sensor using two green light emitting diodes is shown better utility than using one green light emitting diode and red light emitting diode at the ambient light. The waveform and heart rate that measured by two green light emitting diodes are more identical than others. The amount of electricity used is less than red light emitting diode and error peak detectability factor is the lowest.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.1
• /
• pp.1-8
• /
• 2020

If a dangerous situation arises in a place where out of reach from the human, UAVs can be used to determine the size and location of the situation to reduce the further damage. With this in mind, this paper sets the minimum value of the roll, pitch, and yaw using beta flight to detect the UAV's smooth hovering, integration, and derivative (PID) values to ensure that the UAV stays horizontal, minimizing errors for safe hovering, and the camera uses Open CV to install the Raspberry Pi program and then HSV (color, saturation, Brightness) using the color palette, the filter is black and white except for the red color, which is the closest to the fire we want, so that the UAV detects the image in the air in real time. Finally, it was confirmed that hovering was possible at a height of 0.5 to 5m, and red color recognition was possible at a distance of 5cm and at a distance of 5m.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.16 no.4
• /
• pp.330-334
• /
• 1983

The author carried out an experiment to find out the response of gray rock cod, Sebastes inermis (Cuvier et Valenciennes) to the color light. The experimental tank ($360L{\times}50W{\times}55H\;cm$) was set up in a dark room. Six longitudinal sections with 60 cm intervals are marked in the tank to observe the location of the fish. Water depth in the tank was kept 50 cm level. Light bulbs of 20W at the both ends of the tank projected the light horizontally into the tank. Two different colored filters were selected from four colors of red, blue, yellow, and white, and they were placed in front of the light bulbs to make different colors of light. Light intensity were controlled by use of auxiliary filters intercepted between the bulb and the filter. The fishes were acclimatized in the dark for 50 minutes before they were employed in the experiment. Upon turning on the light, the number of fish in each section was counted 40 times in 30 second intervals, and the mean of the number of fish in each section was given as the gathering rate of the fish. The colors favourited by the fish was found in the order of white, blue, yellow and red. The gathering rate of fish on illumination period was small and comparatively fluctuated with stability. The difference of the gathering rates on two different colors of light was much greater, regardless of illumination period, in day time than in night time.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.17 no.3
• /
• pp.191-196
• /
• 1984

The author carried out an experiment to find out the response of filefish, Navodon modestus(Gunther) to the colored lights. The experimental tank($360L{\times}50W{\times}55Hcm$) was set up in a dark room. Six longitudinal sections with 60 cm intervals are marked in the tank to observe the location of the fish. Water depth in the tank was kept 50 cm level. Light bulbs of 20W at the both ends of the tank projected the light horizontally into the tank. Two different colored filters were selected from four colors of red, blue, yellow, and white, and they were placed in front of the light bulbs to make different colors of light. Light intensity were controlled by use of auxiliary filters intercepted between the bulb and the filter. The fishes were acclimatized in the dark for 50 minutes before thor were employed in the experiment. Upon turning on the light, the number of fish in each section was counted 40 times in 30 second intervals, and the mean of the number of fish in each section was given as the gathering rate of the fish. The colors favourited by the fish was found in the order of blue, white, yellow and red. The gathering rate of fish on illumination period was not constant but varied randomly. The difference of the gathering rates on two different colors of light was rather in significant, however the difference was larger in the day time than in the night time.

• The KIPS Transactions:PartC
• /
• v.11C no.7 s.96
• /
• pp.951-958
• /
• 2004

Nowadays NGN is developed for supporting the e-Commerce, Internet trading, e-Government, e-mail, virtual-life and multimedia. Internet gives us the benefit of remote access to the information but causes the attacks that can break server and modify information. Since 2000 Nimda, Code Red Virus and DSoS attacks are spreaded in Internet. This attack programs make tremendous traffic packets on the Internet. In this paper, we designed and developed the Bandwidth Controller in the gateway systems against the bandwidth saturation attacks. This Bandwidth con-troller is implemented in hardware chipset(FPGA) Virtex II Pro which is produced by Xilinx and acts as a policing function. We reference the TBF(Token Bucket Filter) in Linux Kernel 2.4 and implemented this function in HDL(Hardware Description Language) Verilog. This HDL code is synthesized in hardware chipset and performs the gigabit traffic in real time. This policing function can throttle the traffic at the rate of band width controlling policy in bps speed.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.10 no.3
• /
• pp.173-177
• /
• 1977

Optical properties were studied in the Japan Sea based on the optical observations in nine oceanographic stations from September 28 to October 2, 1976. Submarine light intensity was measured by using a submarine illuminometer (RIGO, Type: 2501-A) : equipped with a filter(RIGO, Type:V-R-60, wavelength: 600-620nm). In the upper 40 m depth layer light intensity was measured at 1 m depth interval. The absorption coefficient for red color in the area ranged from 0.142 to 0.323 (mean 0.232) : the Secchi-disc depth in the area ranged from 15 to 23 meters (mean 19.8 meters). The relation ship between absorption coefficient (m) am transparency depth (D) was m =4.93/D. The rates of light penetration for red color at three different depths are computed with reference to the surface light intensity At tile depths of 5 m, 10 m and 20 m, the rates of light penetration were $23.11\%(15-34.2\%),\;6.49\%(3.04-12\%)\;and\;0.698\%(0.113-1.27\%)$ respectively.

• Journal of the Korean Society of Tobacco Science
• /
• v.16 no.1
• /
• pp.26-33
• /
• 1994

A tobacco ripeness grading meter was designed and constructed using the color sensor, its performance was evaluated. A degree of ripeness grading of a leaf is very closely related to the measured tobacco leaf color. Measuring the small amount of the reflectance precisely depends on the apparatus including color sensor, light source, detector sensitivity, and geometric characteristics of appratus. To analyze and minimize the variational effects, experiments to select the proper condition were performed. Because of the combined effect mentioned above, the system has some variation on its response. Basis on the results of the experiments, prototype was developed and interfaced to a computer system. The main components of prototype included a tungsten lamp as a light source, Amorphous full color sensor with three filters, regulated D.C. power supply, OP - AMP(741 TC) for amplification, AR - B3001 board for interfacing to a computer with analog to digital conversion, and a compatible IBM PC XT computer. The experimental results of the developed ripeness tobacco leaf measurement system are summarized as following: [1] The output readings of ripeness grade meter for tobacco leaf, which is based on harvesting time, showed the apparent difference in variety of different quality. It was considered suitable that three filters(red, green, blue) in Amorphous full color sensor could be used in four different ripeness degree measurement of tobacco leaf. [2] The output readings of ripeness grade meter for tobacco leaf, which is based on government procurement, showed apparent difference in variety of different quality. Tobacco leaf varieties to stalk position are divided into tips, leaf, cutters, and primings, It is considered suitable that only red filter in the sensor could be used to classify the grade of tobacco leaf within the same kind tobacco stalk. However, the ripeness grade meter was not adequate to classify all the tobacco grades in the four different tobacco leaves.

• Publications of The Korean Astronomical Society
• /
• v.30 no.2
• /
• pp.217-218
• /
• 2015

In this work, we present the result of our follow-up observations of SDSS J092741.73+332959.1 and SDSS J130733.49+215636.7 using the 2.35 m Thai National Telescope and ULTRASPEC instrument. Both systems are listed among the recently found white dwarf main sequence binaries from the Sloan Digital Sky Survey. SDSS J092741.73+332959.1 is a new PCEB with a period of 2.3 days, the longest orbital period known to date for white dwarf binaries. SDSS J130733.49+215636.7 is confirmed to be an eclipsing system with a period of 0.21 days from the Catalina Survey's light curve, however the parameters for the white dwarf are still uncertain. Our goal is to determine precise parameters for both systems using the Binary Maker 3 software. The observation for SDSS J0927+3329 was done on 9 January 2014 in the SDSS r' filter while the data for SDSS J1307+2156 were taken in the z' filter on 27 April 2014. Our models show that the red dwarf companions in both systems are well constrained inside their Roche Lobes. We find that the binary M2/M1 ratio in SDSS J0927+3329 is close to 0.5, with white dwarf and M-dwarf temperatures of 12000 K and 3300 K, respectively. Our preliminary result for SDSS J1307+2156 show that this system has an extreme mass ratio of 0.3. The white dwarf in this system has a temperature of 7500 K and the companion star has an effective temperature of 3150 K.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1526-1526
• /
• 2001

To improve the accuracy of sweetness sensor in automated sorting operations, it is necessary to clarify unevenness of the sugar content distribution within fruits. And it is expected that the technique to evaluate the content distribution in fruits contribute to the development of the near-infrared (NIR) imaging spectroscopy. Sugiyama (1999) had succeeded to visualize the distribution of the sugar content on the surface of a half-cut green fresh melon. However, this method cannot be applied to red flesh melons because it depends on information of the absorption band of chlorophyll (676 nm), which is affected by the color of the fresh. The objective of this study was to develop the universal visualization method depends on the absorption band of sugar, which can be applied to various kinds of melons and other fruits. The relationship between the sugar contents and absorption spectra of both green and red fresh melons were investigated by using a NIR spectrometer to determine the absorption band of sugar. The combination of 2$\^$nd/ derivative absorbances at 902 nm and 874 nm was highly correlated with the sugar contents. The wavelength of 902 nm is attributed to the absorption band of sugar. A cooled charge-coupled device (CCD) imaging camera which has 16 bit (65536 steps) A/D resolution was equipped with rotating band-pass filter wheel and used to capture the spectral absorption images of the flesh of a vertically half-cut red fresh melon. The advantage of the high A/D resolution in this research is that each pixel of the CCD is expected to function as a detector of the NIR spectrometer for quantitative analysis. Images at 846 nm, 874 nm, 902 nm and 930 nm were acquired using this CCD camera. Then the 2$\^$nd/ derivative absorbances at 902 nm and 874 nm at each pixel were calculated using these four images. On the other hand, parts of the same melon were extracted for capturing the images and squeezed for the measurement of sugar content. Then the calibration curve between the combination of 2$\^$nd/ derivative absorbances at 902 nm and 874 nm and sugar content was developed. The calibration method based on NIR spectroscopy techniques was applied to each pixel of the images to convert the 2$\^$nd/ derivative absorbances into the Brix sugar content. Mapping the sugar content value of each pixel with linear color scale, the distribution of the sugar content was visualized. As a result of the visualization, it was quantitatively confirmed that the Brix sugar contents are low at the near of the skin and become higher towards the seeds. This result suggests that the visualization technique by the NIR imaging spectroscopy could become a new useful method fer quality evaluation of melons.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.23 no.4
• /
• pp.151-156
• /
• 1987

The author carried out an experiment to find out the response of sea-bass, Epinephelus septemfasciatus (Thunberg) to the color lights. The experimental tank (360L$\times$50W$\times$55H cm) was set up in a dark room. Six longitudinal sections with 60 cm intervals are marked in the tank to observe the location of the fish. Water depth in the tank was kept 50 cm level. Light bulbs of 20 W at the both ends of the tank projected the light horizontally into the tank. Two different colored filters were selected from four colors of red, blue, yellow, and white, and they were placed in front of the light bulbs to make different colors of light. Light intensity were controlled by use of auxiliary filters intercepted between the bulb and the filter. The fishes were acclimatized in the dark for 50 minutes before they were employed in the experiment. Upon turning on the light, the number of fish in each section was counted 40 times in 30 second intervals, and the mean of the number of fish in each section was given as the gathering rate of the fish. The colors favourited by the fish was found in the order of blue, red, white and yellow in day time, and red, blue, yellow and white at night time. The gathering rate of fish on illumination period was not constant and fluctuated with irregularity. The difference of the gathering rate on two different colors of light was small and the difference was larger in night time then in day time.