• 한국건설순환자원학회논문집
• /
• 제6권3호
• /
• pp.214-221
• /
• 2018

본 논문에서는 페로니켈슬래그 미분말 및 혼화재의 복합사용이 VR 하수관 강도발현에 미치는 영향분석에 관한연구를 실시하였다. 치환율을 변수로 시험을 실시하였으며, 휨강도 및 압축강도의 결과분석과 SEM 분석을 통한 강도발현 성능연구를 실시하였다. 휨강도 및 압축강도, SEM을 통한 미시적 분석을 통해, 각 경우 별 상관관계를 도출 할 수 있었다. 치환율은 OPC 질량대비 20%, 30%를 구분하여 페로니켈 슬래그 미분말 및 혼화재를 일정 비율로 치환하여 실시하였다. 치환율 20%일 경우 강도발현 성능이 우수한 것으로 나타났으며, 휨 강도와 압축강도는 페로니켈 슬래그 미분말, 생석회, 석고, 염화칼슘을 혼화재로 복합사용 하였을 때 강도발현 성능이 가장 우수하였으며, 조밀한 미세구조 형태를 나타냈고, 재령 28일 이후에도 점진적 강도발현 가능성이 보인다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.2101-2106
• /
• 2011

It is reported that about more than 45% of damage shown in railroad rails include breakage of rail end which cross the center of Thermit welded zone. Thermite welding is always accompanied by numerous aluminum oxide and secondary inclusions, which may have a negative influence on the ductility and toughness of the weld metal. In this study the aluminum powder recycled by waste aluminum can was used for iron oxide generated after the process of welding rod and the remain aluminum was reduced by minimizing the quantity of aluminum. And complete dissolution was induced by using ferro Mn powder as the additive element. This study reviewed the applicability of heat treatment in the welded zone of rail using ceramic heating pad by carrying it out. This study could observe the improvement of the mechanical characteristics (UTS and elongation) and the changes of failure mechanism from brittleness to ductility. It could be found that improved strength and elongation result from pearilte fine structure.

• 한국농공학회논문집
• /
• 제51권4호
• /
• pp.21-27
• /
• 2009

This study was performed to evaluate the physical and mechanical properties of porous concrete using waste activated carbon. Material used were ordinary portland cement, recycled coarse aggregate, waste activated carbon and superplasticizer. The replacement ratios of waste activated carbon were 0,1,2,3,4,5,6,7,8,9, and 10 %. The void ratio was decreased and ultrasonic pulse velocity was increased with increasing the waste activated carbon powder, respectively. The compressive strength and flexural strength of porous concrete using waste activated carbon powder were in the range of 8.21${\sim1}$6.58 MPa and 1.69${\sim1}$3.68 MPa, respectively. The pH degree of porous concrete in 1day and 77days were shown in 12.50${\sim1}$12.63 and 10.21${\sim1}$10.70, respectively. Accordingly, waste activated carbon can be used for porous concrete material.

• Elastomers and Composites
• /
• 제50권4호
• /
• pp.245-250
• /
• 2015

Recycling of ethylene-propylene-diene terpolymer (EPDM) scrap was tried by blending with polypropylene (PP). EPDM scrap powder was prepared by shear pulverization process at high temperature, which may lead to selective chain scission induced by difference in the critical elastic coefficient. On the other hand, EPDM scrap powder was prepared by adding a selected reclaiming agent during shear pulverization process at high temperature. Terpene as a bonding agent was then introduced to improve adhesion property. PP, used as a matrix for manufacturing thermoplastic elastomer, was modified by the incorporation of dicumyl peroxide and maleic anhydride. The functionalized EPDM and modified PP were blended and cured dynamically at $190^{\circ}C$. The blend materials prepared in this study showed the comparable results to those of conventional TPE in terms of tensile and flow properties. Also, the odor component of recycled EPDM was analyzed using GC-MS.

• 마이크로전자및패키징학회지
• /
• 제24권1호
• /
• pp.1-8
• /
• 2017

Fe-9.8Si-6.0Al mother alloy was manufactured using by Fe-3.5Si recycled scrap and Si powder. And then, soft magnetic alloy powder of $D_{50}$ size and sphere type were prepared by gas atomization process. To obtain the soft magnetic powder of a high aspect ratio, in the first, we conducted the ball milling process for 8 hours. And heat treatment was performed under $650^{\circ}C$, 2 hours and $N_2$ atmosphere condition for reducing the residual stress of the powder. Based on these process, we made around $50{\mu}m$ diameter Fe-9.8Si-6.0Al powder, which morphology and shape was a similar to the commercial Fe-Si-Al powder. Finally, the soft magnetic sheets were prepared by tape casting process using by those powders. The permeability of the tape casting sheet was measured, and we confirmed the possibility of reusing to the soft magnetic materials of Fe-Si electric sheet scrap.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.881-884
• /
• 2008

현재 국내에서 많은 양의 도자기 폐기물이 발생하고 있으며, 이들 폐기물은 경제적 이득과 환경보전의 차원에서 재활용하는 방안이 모색되어져야 한다. 따라서, 본 연구에서는 도자기 폐기물을 시멘트 혼합재로 이용하여 폐도자기의 재활용성을 검증하고자 하였다. 실험 결과 시멘트 혼합재로 사용된 폐도자기분말이 5%, 7%까지 PHC파일의 압축강도에 영향을 주었으며, 폐도자기분말을 시멘트 혼합재로 사용하여 PHC파일의 강도를 개선시킬 수 있었다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 봄 학술논문 발표대회
• /
• pp.77-78
• /
• 2020

In Korea, more than 30,000 tons of waste Styrofoam are produced every year. Styrofoam is spent more than 500 years decomposing during the reclamation process, so it needs to be recycled. The recycling rate of waste styrofoam continues to be the third highest in the world, but it is lower than that of Germany and Japan. Therefore, measures are needed to increase the recycling rate of waste Styropol. Another problem is that cement is mainly used in existing lightweight foam concrete. However, large amounts of CO2 from cement-producing processes cause environmental pollution. Currently, Korea is increasing its greenhouse gas reduction targets to cope with energy depletion and climate change, and accelerating efforts to identify and implement reduction measures for each sector. In 2013 alone, about 600 million tons of carbon dioxide was generated in the cement industry. Therefore, this study replaces CO2 generation cement with furnace slag fine powder, uses crude steel cement for initial strength development of bubble concrete, and manufactures hardening materials to study its properties using waste styrofoam. As a result of the experiment, the hardening agent replaced by micro powder of furnace slag was less intense and more prone to absorption than cement using ordinary cement. Further experiments on the segmentation and strength replenishment of furnace slag are believed to contribute to the manufacture of environmentally friendly lightweight foam concrete.

• Advances in materials Research
• /
• 제12권4호
• /
• pp.331-349
• /
• 2023

Foam concrete can be considered as environmental friendly material due to its low weight, its minimal cost and a possibility to add waste materials in its production. This paper investigates the possibility of producing foam concrete with waste glass as powder and aggregate. Then, the effect of using waste glass on strength and drying shrinkage of foam concrete was examined. Also, the effect of incorporating polypropylene fibers (12 mm length and proportion of 0.5% of a mix volume) on distribution of waste glass as coarse particles within 1200 kg/m³ foam concrete mixes was evaluated. Waste glass was used as powder (20% of cement weight), as coarse particles (25%, 50% and 100% instead of sand volume) and as fine particles (25% instead of sand volume). From the results, the problem of non-uniform distribution of coarse glass particles was successfully solved by adding polypropylene fibers. It was found that using of waste glass as coarse aggregate led to reduce the strength of foam concrete mixes. However, using it with polypropylene fibers in combination helped in increasing the strength by about 29- 50% for compressive and 55- 71% for splitting tensile and reducing the drying shrinkage by about (31- 40%). In general, not only the fibers role but also the uniformly distributed coarse glass particles helped in improving and enhancing the strength and shrinkage of the investigated foam concrete mixes.

• 한국건설순환자원학회논문집
• /
• 제6권2호
• /
• pp.74-80
• /
• 2011

본 연구에서는 대표적인 콘크리트용 산업부산자원인 플라이애쉬와 고로슬래그미분말을 교량 덧씌우기용 고성능 콘크리트에 적용하기 위하여 배합조건별 역학특성과 자기수축 특성 및 내염특성을 평가하였으며, 평가결과 수경성 광물질 혼화재의 혼합사용은 염분과 알칼리 골재 반응에 대한 저항성 개선효과로 내구성 증진에 크게 기여하고 자기수축 변형에 대한 저항성 개선에도 효과가 있는 것으로 나타났다. 이 고성능 콘크리트는 재료와 시공 측면에서 내구성과 효율성을 개선시킨 콘크리트로서 폐자원의 활용으로 인한 친환경, 경제성까지 확보할 수 있을 것으로 사료된다.

• Safety and Health at Work
• /
• 제10권4호
• /
• pp.518-526
• /
• 2019

Background: Additive manufacturing (AM) is a rapidly expanding new technology involving challenges to occupational health. Here, metal exposure in an AM facility with large-scale metallic component production was investigated during two consecutive years with preventive actions in between. Methods: Gravimetric analyzes measured airborne particle concentrations, and filters were analyzed for metal content. In addition, concentrations of airborne particles <300 nm were investigated. Particles from recycled powder were characterized. Biomonitoring of urine and dermal contamination among AM operators, office personnel, and welders was performed. Results: Total and inhalable dust levels were almost all below occupational exposure limits, but inductively coupled plasma mass spectrometry showed that AM operators had a significant increase in cobalt exposure compared with welders. Airborne particle concentrations (<300 nm) showed transient peaks in the AM facility but were lower than those of the welding facility. Particle characterization of recycled powder showed fragmentation and condensates enriched in volatile metals. Biomonitoring showed a nonsignificant increase in the level of metals in urine in AM operators. Dermal cobalt and a trend for increasing urine metals during Workweek Year 1, but not in Year 2, indicated reduced exposure after preventive actions. Conclusion: Gravimetric analyses showed low total and inhalable dust exposure in AM operators. However, transient emission of smaller particles constitutes exposure risks. Preventive actions implemented by the company reduced the workers' metal exposure despite unchanged emissions of particles, indicating a need for careful design and regulation of the AM environments. It also emphasizes the need for relevant exposure markers and biomonitoring of health risks.